Size a gas water heater by matching its delivery rating to your peak-hour demand or its flow rate to your simultaneous fixtures.
For the full breakdown, see our best Gas Water Heater guide.
A cold shower at 7 a.m. is usually a sizing failure, not a broken heater. The unit ran out of hot water because it was chosen by tank gallonage or by counting people in the house — two shortcuts that ignore how much water your household actually draws in its busiest hour.
The method below comes straight from Department of Energy sizing guidance and works for both storage and tankless units. Pick your technology first, then run the numbers.
How Do You Size A Storage Tank Gas Water Heater?
Match the heater’s First-Hour Rating to your household’s busiest one-hour hot-water demand, not to the number of people living there.
The First-Hour Rating, or FHR, is the gallons of hot water a fully heated tank can deliver in one hour — stored water plus what the burner recovers along the way. Two tanks with the same nominal volume can carry different FHRs because heat input and recovery speed vary.
Here’s how to build your target number:
- Find the hour when your household uses the most hot water.
- Add up every gallon drawn in that hour — showers, baths, sinks, dishwasher, clothes washer, anything hot.
- Choose a model whose FHR meets or slightly exceeds that total.
Overshooting wastes money on a bigger burner; undershooting leaves you in the cold. Residential storage tanks commonly range from 40 to 80 gallons, so there’s usually a model near your number.
What Numbers Do You Need For A Tankless Gas Water Heater?
Tankless sizing needs two values: your maximum simultaneous flow rate in gallons per minute, and the temperature rise from incoming cold water to your target outlet temperature.
To find the flow rate, list the fixtures that could realistically run at the same time and add their rates. DOE’s example ranges give you a starting point: bath sinks draw 0.5–1.5 gpm, showerheads 1.5–2.5 gpm, bathtubs 2.0–4.0 gpm, kitchen sinks 1.0–2.5 gpm, and dishwashers 1.0–3.0 gpm.
Then calculate temperature rise. DOE identifies 120°F as the desired outlet temperature for most uses, so subtract your incoming water temperature from that. A northern utility delivering 45°F water in January means a 75°F rise — a far harder job than the same unit faces in Florida at 70°F inlet.
Now check the manufacturer’s performance chart at that exact temperature rise. A headline “9 gpm” means nothing if the chart shows 4 gpm at your rise.
Low-flow fixtures can fall below that threshold.
| Storage Unit Sizing Step | Tankless Unit Sizing Step |
|---|---|
| Find your busiest hot-water hour | List fixtures that run simultaneously |
| Total gallons drawn in that hour | Add their gpm flow rates |
| Match First-Hour Rating to that total | Subtract inlet temp from 120°F |
| Stay within 2 gallons of demand | Read the chart at that exact rise |
| Confirm vent, gas line, clearance | Confirm gas Btu capacity and venting |
| Check tank fits the space | Verify 0.5 gpm ignition threshold |
Once your numbers are in hand, comparing real units becomes far easier — this roundup of tested gas water heaters lists capacity, FHR, and flow specs side by side.
What Mistakes Send Sizing Off The Rails?
The costliest error is buying by tank volume or headcount while skipping the demand calculation entirely.
- Treating peak gpm as constant. A tankless unit’s maximum flow only holds at a low temperature rise. Cold winter inlet water cuts output sharply.
- Ignoring winter inlet temperature. Size for the coldest month, not the mildest.
- Double-counting demand. Adding every fixture’s flow when nobody showers while the dishwasher and washer run inflates your number. Underestimating overlap does the same damage in reverse.
- Assuming a drop-in replacement. A higher-Btu unit may need a larger gas line, different venting, and fresh clearances. DOE notes gas-line sizing must follow the manufacturer’s instructions and applicable plumbing and building codes.
- Overlooking low-flow fixtures. They save water but may sit below a tankless unit’s activation flow.
- Setting the thermostat too high. DOE identifies 120°F as the usual target; higher settings raise scald risk without buying you more capacity.
Before purchase, confirm gas supply capacity, venting, combustion air, electrical needs, clearances, water connections, and physical dimensions. Gas connections, venting, and startup typically need a qualified professional, and local rules vary.
Common Questions
Can I size a water heater by counting family members?
Counting people gives a rough starting guess, but it misses how your household actually behaves. Two people who shower back-to-back and run laundry together can outdraw four people on staggered schedules. Peak-hour demand in gallons is the number that matters.
Is a bigger tank always a safer choice?
A larger tank isn’t automatically better. An oversized unit costs more upfront and runs less efficiently at light loads, while an undersized one leaves you short. The goal is an FHR within roughly 2 gallons of your calculated demand.
Does a tankless unit really deliver its advertised flow rate?
Only at the temperature rise printed in the manufacturer’s chart. The same unit moves far fewer gallons when incoming water is cold. Always read the performance table at your actual inlet temperature before buying.
Sources
- U.S. Department of Energy. “Tankless Water Heaters” Covers flow rates, temperature rise, and tankless sizing method.
- U.S. Department of Energy. “Measure Guide: Tankless Water Heaters” Supports fixture flow ranges and installation requirements.