A soundbar should fit beneath your TV without blocking the screen or remote sensor, then match its power and surround options to your room’s size and acoustics — not to screen inches alone.
One blocked infrared sensor turns a new soundbar into a daily annoyance, and the cause is almost always the same: buying by screen size before measuring the shelf. TV dimensions make a decent visual-proportion guide, but the number on the box tells you nothing about how a bar will sound in a room with bare walls, a vaulted ceiling, and a hard floor. Room volume, seating distance, and the TV’s available ports decide far more of the outcome.
Here is the sequence that works: measure the space, size the bar to the room, confirm the connections, then add surrounds or a subwoofer only after the main bar is running properly. The sections below walk through each step, including the clearances Sonos publishes for wall-mounted installations and the HDMI-versus-optical split that quietly decides whether Dolby Atmos will ever play.
Measure The Fit Before Anything Else
A soundbar has to clear the screen, the infrared sensor, and the remote’s path to that sensor, so measure width and height first and treat every other spec as secondary. Bars mounted below a TV need breathing room; a bar pressed against a panel or blocking its sensor is a return waiting to happen.
For a wall-mounted Sonos Playbar, Sonos specifies at least 1 inch (25 mm) between the bar and the TV when mounted below, at least 2 inches (50 mm) when mounted above, and at least 1 foot (30 cm) of clearance from each end to a wall or obstruction. Those figures come from Sonos’s TV requirements for home theater speakers, and they are a useful sanity check for any brand: the sensor sits near the bottom edge on most sets, so the bar’s top edge is the one to watch.
Check the furniture too. A bar that overhangs the console by a few inches looks unbalanced and vibrates more; a bar that sits snug on a solid shelf with an inch of air behind it behaves better than one wedged into a closed cabinet door.
How to Match Soundbar Size to Your Room and TV
The TV’s width is a proportion guide, not a rule: a bar slightly narrower than the display or similar in width integrates cleanly, while a bar far narrower looks visually off. Room volume decides more about sound than screen size ever will.
A compact bar suits a small, furnished room where seating is close. A longer, wider bar with dedicated surround processing earns its cost in a large or open-plan space, especially one with high ceilings. Big model in a small, reflective room can sound bloated and boomy; small model in a great room can lack scale and leave dialogue thin.
Acoustics finish the job. Hard floors, glass, and bare walls bounce sound and smear dialogue, while rugs, curtains, and soft furnishings soak up reflections. Keep the bar unobstructed and aimed toward where people actually sit, and leave clearance behind it rather than pushing it flat against a wall. Sonos also recommends room-correction tuning where the product supports it, which is worth using on any hard-surfaced room.
| Room and TV Setup | Soundbar Format That Fits | What To Watch |
|---|---|---|
| Small room, TV 43–55 inches, close seating | Compact single bar | Height clearance under the screen; sensor path clear |
| Medium living room, TV 55–65 inches | Bar with wireless subwoofer | Sub placement near a wall corner for stronger low bass |
| Large or open-plan room, TV 65 inches and up | Longer bar with sub and rear surrounds | Surrounds need positions behind and to each side of the seat |
| High ceiling, hard floors, glass walls | Bar with room-correction tuning | Reflections smear dialogue; correction helps most here |
| Wall-mounted TV, no console | Bar mounted below or above per manufacturer clearance | Sonos Playbar needs 1 inch below, 2 inches above |
| Older TV with optical only | Bar with digital optical input | No CEC control or voice control over optical on some models |
| TV with HDMI eARC and a streaming plan that carries Atmos | Atmos-capable bar over HDMI eARC | Lossless TrueHD Atmos needs eARC, not plain ARC |
Check Ports and the Atmos Chain Before You Buy
Dolby Atmos is a chain, not a checkbox: the TV, the cable, the source device, the streaming service, the subscription tier, and the specific program all have to cooperate. A bar marketed as Atmos-ready will not produce height effects if any link in that chain breaks.
Sonos lists Arc, Arc SL, Arc Ultra, and Beam (Gen 2) as Atmos-capable, and notes that Atmos from a TV requires HDMI ARC or eARC. Plain ARC commonly carries Dolby Digital Plus Atmos, while lossless Dolby TrueHD Atmos needs eARC. On the input side, Sonos Ray, Playbar, and Playbase require a digital optical output; Arc, Arc SL, Arc Ultra, Beam, and Amp require HDMI ARC for CEC and supported voice-assistant control. Optical works on some models with an adapter, but CEC and voice control drop away.
Streaming hardware matters as much. Older Fire TV generations may not support Atmos at all, and some TVs re-encode incoming audio down to Dolby Digital 5.1. If you are weighing which bars are worth the money once those limits are clear, this tested surround sound soundbar roundup covers the practical picks.
Set It Up in the Right Order
Configure the main bar first and add surrounds or a subwoofer only after it works, because model compatibility is not universal across a brand’s lineup.
- Place the bar below or above the TV with the manufacturer’s required clearances, then connect power.
- Connect the TV’s HDMI ARC or eARC port where available. Use optical only when you must, and accept the control and format limits that come with it.
- Connect cable boxes, game consoles, and disc players to the TV directly, as the manufacturer requires.
- Set the TV and the source device to a supported audio format — an unsupported format can silence surround or Atmos playback entirely.
- Run setup through the manufacturer’s mobile app. Sonos Playbar setup needs the Sonos app for iOS or Android plus the supplied optical cable.
- Add compatible surrounds or a subwoofer once the bar itself is confirmed working. Surrounds go behind and to the left and right of the listening position, both facing the same way.
When it works, the app shows the bar as connected and dialogue comes from the screen rather than the TV’s own speakers. If the app cannot find the bar, recheck the cable seated in the TV’s ARC-labeled port — that is the usual culprit.
Common Questions
Does a bigger soundbar always sound better?
No. A large bar in a small, reflective room can sound excessive and boomy, while a compact bar in a big open room can lack scale and leave dialogue thin. Match the bar’s output to room volume and seating distance first, then use the TV’s width as a visual proportion check.
Can I get Dolby Atmos with an optical cable?
Not the full experience. Sonos states that Atmos from a TV requires HDMI ARC or eARC. Optical can carry a standard surround signal on some models with an adapter, but CEC control and voice-assistant control are unavailable over optical, and height effects will not come through.
Where should rear surround speakers go?
Sonos recommends placing surrounds behind and to the left and right of the usual listening position, with both speakers set in the same orientation. Add them only after the main bar is configured, since compatible models vary and are not universal across a lineup.
Sources
- Sonos. “TV Requirements for Sonos Home Theater Speakers” Supports mounting clearances, port requirements, and setup order.
- Sonos. “Surround Sound Guidelines and Limitations” Supports surround placement, speaker clearance, and room-correction advice.
- Sonos. “Listen to Dolby Atmos Audio From Your TV on Sonos” Supports the Atmos compatibility chain and source-device caveats.