Size a bathroom fan by matching CFM to square footage and sones to how quiet you want it — 80 CFM for a typical 50–79 sq. ft. bathroom, and 1.0 sone or less if noise bothers you.
Wrong sizing shows up months later as peeling paint, a mirror that stays fogged, or a fan you stop running because it roars. Two numbers decide it: CFM for airflow, sones for noise. Here’s the math, the loudness scale, and the fit checks that determine whether a replacement slides into your ceiling.
How Much CFM Does Your Bathroom Need?
Bathrooms under 100 square feet usually follow a simple rule: roughly 1 CFM per square foot — 60 sq. ft. wants about 60 CFM, 90 wants around 90. Broan-NuTone’s bathroom exhaust fan buying guide pairs each fan to a recommended room size, tracking that ratio closely.
Larger rooms — or any bath with tall ceilings, a soaking tub, a steam shower, or heavy daily showering — need more than floor area suggests; use fixture-based sizing instead.
A second check uses air changes: length × width × ceiling height, divide by 60, multiply by 8 (eight air changes per hour). A 6 × 10 × 10-foot bathroom holds 600 cubic feet; 600 ÷ 60 × 8 = 80 CFM. Both methods should land close — that’s your signal the number is right.
| Bathroom Size | Typical CFM | Notes |
|---|---|---|
| Up to 45–50 sq. ft. | 50 CFM | Half baths and small full baths |
| 46–75 sq. ft. | 70–80 CFM | Standard hall bathroom range |
| 50–79 sq. ft. | 80 CFM | Most common US bathroom size |
| 76–105 sq. ft. | About 110 CFM | Primary baths with shower and tub |
| 80–99 sq. ft. | About 100 CFM | Alternative sizing table figure |
| Over 100 sq. ft. | Fixture-based sizing | Volume beats floor area alone |
| High moisture load | Add capacity | Steam shower, big tub, long duct |
More CFM isn’t automatically better: a big fan on undersized ducting gets restricted airflow plus extra noise, working harder without clearing the room faster.
What Do Sone Ratings Actually Mean?
Sones measure perceived loudness; lower is quieter. Broan-NuTone’s explainer on what a sone is puts 1.0 sone at roughly refrigerator-level hum, which most people find unobtrusive.
- Below 0.3 sones — virtually silent
- 0.3–0.9 sones — very quiet
- 1.0–1.5 sones — generally considered quiet
- 1.5–3.0 sones — moderate; noticeable in a small room
- Above 3.0 sones — clearly audible
A quiet rating never excuses weak airflow — compare CFM and sones side by side. Sone figures assume correct ducting; a kinked or undersized run makes any fan louder than its label.
What Should You Measure Before Buying?
Pull the grille and measure the ceiling opening before ordering. Housing dimensions and duct diameter decide what fits; no spec sheet fixes a mismatch after the box arrives.
- Record the ceiling-opening width and, if reachable, the housing dimensions.
- Note the duct diameter — 3, 4, and 6 inches are common.
- Confirm construction depth, voltage, amperage, and room-side installation support.
- Verify the exhaust vents outdoors, and check locally adopted mechanical and electrical codes.
- Over a tub or shower, use only a model explicitly listed for that location and connect it to a GFCI-protected circuit where specified.
- Weigh features: ENERGY STAR certification, humidity sensing, built-in lighting, continuous operation, timers.
Real examples: the Broan 678 delivers 50 CFM at 2.5 sones for a 45-square-foot bath; the Broan BEL6F pushes 60 CFM at 0.9 sones for the same room.
To compare finished units rather than spec sheets, this roundup of tested bathroom ventilation fans pairs real models with airflow and noise ratings.
The Four Sizing Mistakes That Cost the Most
Most bad installs trace back to a skipped measurement, not a bad fan:
- Floor area only. Ceiling height, steam showers, and large tubs change the real load.
- Reusing small duct. A higher-CFM fan on 3-inch duct chokes airflow and adds noise.
- Chasing silence. A quiet fan that can’t clear humidity leaves moisture behind.
- Ignoring the housing. Buying before measuring turns a swap into a drywall project.
Manufacturer recommendations guide the choice; your locally adopted codes govern the install.
Common Questions
Can I oversize a bathroom exhaust fan?
Yes, but there’s little benefit. A fan well above the room’s need won’t clear moisture much faster if the duct can’t keep up, and oversized units often run louder. Match CFM to square footage and moisture load, then spend extra budget on a lower sone rating.
Is a 1.0 sone fan quiet enough for a small bathroom?
For most people, yes. One sone sits near refrigerator-level sound and fades into the background in a small room. If the fan shares a wall with a bedroom, look below 0.9 sones. A poor duct run can make any fan louder than its rating suggests.
Do I need a special fan over a shower?
Yes. Use only a model explicitly listed for bathtub or shower installation, and wire it to a GFCI-protected circuit where required. An unlisted standard fan inside a shower enclosure can fail early and creates a real electrical hazard.
Sources
- Broan-NuTone. “Bathroom Exhaust Fan Buying Guide” Source for CFM-to-room-size sizing and duct guidance.
- Broan-NuTone. “What Is a Sone?” Source for the sone loudness scale.
- Broan-NuTone. “Bath & Exhaust Ventilation Fan FAQs” Source for sizing figures and installation checks.