Four wood boring drill bit families cover most jobs: auger bits for deep, fast holes, spade bits for cheap large-diameter holes, Forstner bits for smooth flat-bottomed holes, and brad-point bits for accurate general-purpose drilling.
Grab the wrong bit and a clean cabinet panel turns into a splintered mess, or a deep hole through a stud wall stalls halfway. The four families below split the work by purpose rather than by brand, and each one has a job it does better than the rest. Match the bit to the hole, and the drilling gets faster and cleaner at the same time.
What Does Each Bit Actually Do?
Auger bits pull themselves through wood with a screw point and clear chips through deep flutes, spade bits cut fast and cheap in large diameters, Forstner bits leave a smooth flat bottom, and brad-point bits start accurately without wandering.
Auger bits lead with a screw point that draws the bit into the wood while the flutes carry chips out. That combination suits deep holes in framing lumber where chip removal matters. Bosch specifies its Daredevil auger bits for rotary drills and drivers, and lists an effective overall length of 6-1/2 in. for work between studs and in tight spaces. Bosch’s High-Speed Auger Bits use reinforced tips intended to deliver up to 2× longer life than standard auger bits.
Spade bits — paddle bits to most people — are flat and inexpensive, built to bore large-diameter holes quickly in wood. They fit rough or concealed work like routing cable, pipe, and fasteners through studs, not showpiece joinery. Bosch sells Daredevil spade bits in Standard, Extended Length, Stubby Length, and set variants for corded and cordless drills, and describes the spur-and-reamer tips as pre-cutting the wood and clearing chips faster for cleaner holes.
Forstner bits cut with a circular rim and interior cutters to produce accurate, smooth, flat-bottomed holes. Blind holes, overlapping holes, edge holes, end grain, and any hole that needs a clean finish all belong here. Bosch states its Forstner bits are designed for “perfectly smooth, flat-bottomed and splinter-free holes,” including in end grain and through knots, and lists them for portable drills or stationary machines.
Brad-point bits carry a sharp center spur for accurate starting plus outer spurs that score the perimeter before the main cutters lift material. Bosch specifies them for portable drills and drill presses, with extra-wide flutes for chip removal. The brad point is the general-purpose wood bit when a clean entry hole matters more than speed.
Which Bit Fits Which Job?
Pick by the hole you need, not by the bit you already own: deep and fast points to auger, big and rough points to spade, flat-bottomed and precise points to Forstner, accurate and general points to brad point.
| Bit Type | Best For | Watch Out For |
|---|---|---|
| Auger | Deep holes in studs and framing; fast chip clearing | Rated for rotary drills only — check the model before impact use |
| Spade | Large-diameter rough holes; cable and pipe runs | Rough finish; poor choice for a visible hole |
| Forstner | Flat-bottomed blind holes, overlapping holes, end grain | Needs a drill with enough power to turn the rim |
| Brad point | Accurate general-purpose holes in soft and hard wood | Center spur can wander on very hard, angled surfaces |
Shank compatibility decides whether a bit even fits your tool. Bosch states its brad-point bits use cylindrical shanks compatible with three-jaw drill chucks, while the 7-piece FB700 Forstner set uses a hex shank compatible with standard three-jaw drills and hexagonal drill-driver chucks. Verify the individual model’s impact rating before driving any wood bit with an impact driver — Bosch lists the cited auger bits for rotary drills and drivers and the spade families for corded and cordless drills, which is not the same as an impact rating.
The most common mistakes follow from skipping that check: a spade bit used for a visible finish hole, a Forstner bit spun in an underpowered handheld drill, a bit too short for the required depth, or an unclamped workpiece that walks. Clamp the stock, keep hands clear, wear eye protection, and back the bit out periodically when chips pile up. For a side-by-side look at specific models before you commit, this roundup of tested wood boring drill bits compares the options in each family.
How Do You Size A Bit For The Hole?
Size the bit to the fastener or cable passing through it, then confirm the bit’s total length clears the depth you need. Bosch’s brad-point range shows how much that varies: the 1/8-in. BP14601 runs 2-7/16 in. overall with a 1/8-in. shank, while the 5/8-in. BP14609 runs 6-1/4 in. overall on a 3/8-in. shank. The larger the diameter, the longer the bit and the heavier the shank it needs.
Brad-point bits scale predictably across the line — the 3/16-in. BP14602 measures 3-5/16 in. overall, the 1/4-in. BP14603 measures 3-3/4 in., the 5/16-in. BP14604 measures 4-1/2 in., the 3/8-in. BP14605 measures 4-3/4 in., the 7/16-in. BP14606 measures 5-5/8 in. on a 5/16-in. shank, and the 1/2-in. BP14607 measures 5-15/16 in. on a 3/8-in. shank. Bosch also sells a 5-piece brad-point set (BP14616).
The FB700 Forstner set covers seven diameters — 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, and 1 in. — each with a 4-in. total length and 3/8-in. hex shank. Most of the manufacturer documentation establishes applications, sizes, and tool compatibility rather than a universal speed chart, so exact RPM and feed settings belong to the specific bit’s own instructions.
What Should You Check Before Buying?
Confirm three things before any bit goes in the cart: the shank matches your chuck, the total length clears the hole depth, and the bit’s application matches your material and finish needs.
Auger bits earn their price when you drill deep holes in lumber regularly — Bosch’s wood drill bit overview lays out the auger and spade families and their intended drills. Spade bits stay the budget pick for anything hidden inside a wall. Forstner bits pay off wherever a hole has to look good or hold a flush plug, and brad-point bits handle the everyday drilling that fills most projects. Bosch’s specifications for Forstner bits and brad-point drill bits list the model-level dimensions worth checking against the job.
A small, deliberate kit beats a full drawer of mystery bits: one auger in the diameter your cable runs need, one Forstner for clean recesses, and a brad-point set covering the common small sizes. Add spade bits in the large diameters only when a rough hole is genuinely all you need.
Common Questions
Can I use a spade bit in a drill press?
Bosch lists its spade-bit families for corded and cordless drills rather than drill presses. A drill press runs at lower speeds than most spade bits are intended for, and the flat paddle can grab in deep cuts. Use a Forstner bit in the drill press when you need a large, clean hole instead.
Why does my Forstner bit burn the wood?
Burning usually means the bit is spinning too fast for its diameter or the feed is too slow, so the rim rubs instead of cutting. It also happens when the drill lacks the power to keep the rim turning under load. Drop the speed, increase steady pressure, and confirm the bit suits a handheld drill.
Do brad-point bits work in an impact driver?
Not by default. Bosch specifies its brad-point bits for portable drills and drill presses and uses cylindrical shanks for three-jaw chucks, which is not an impact rating. Check the individual model’s rating before using an impact driver, and use a standard drill chuck when in doubt.
Sources
- Bosch. “Wood Drill Bits.” Covers auger and spade bit families, applications, and specified drill compatibility.
- Bosch. “Forstner Bits.” Specifies flat-bottomed hole performance and the FB700 set dimensions.
- Bosch. “Brad Point Drill Bits.” Source for brad-point model numbers, total lengths, and shank diameters.