What Is a Starter Rebuild Kit and What Does It Include | Parts, Fitment, Cost

A starter rebuild kit is a parts package for refurbishing an existing electric starter instead of replacing the whole assembly, and most kits contain only the wear items.

Whether a kit works comes down to one question: which components inside your specific starter are actually worn out.

What Does a Starter Rebuild Kit Actually Include?

Contents vary by starter design, but kits fall into two groups: solenoid-only contact kits and fuller kits that also replace brushes, bushings, and seals.

Solenoid contact kits are most common. That’s a solenoid refresh, nothing more.

Fuller kits add the spinning parts. Motor City Reman’s 79-85107 and 79-85106 each include a brush holder, brushes, bearings and/or bushings, seals, insulators, and hardware. Both are 12-volt kits for Mitsuba starters on specified powersports applications, and both require the existing armature to be good.

Air-starter repair kits are different entirely, with vanes, gaskets, and special seals built to the original manufacturer’s specs.

Kit What’s Inside Listed Price
Dorman HELP! 02349 Solenoid contacts, insulators, bolts, nuts, washers, O-rings About $31–$37
Motor City Reman 79-85107 Brush holder, brushes, bearings/bushings, seals, hardware About $35 (compares at $41)
Motor City Reman 79-85106 Brush holder, brushes, bearings/bushings, seals, hardware Similar range
Volt Tech Hitachi kit Brushes, holder, springs, through-bolts, end bushing Varies by seller
Witchdoctors Victory kit Motorcycle starter wear parts About $35 (compares at $40)
Air-starter repair kit Vanes, bearings, gaskets, O-rings, seals Varies widely

What a Kit Will Not Include

No standard kit ships with the expensive hardware: the armature, housing, field coils, solenoid body, pinion gear, and drive assembly are almost never in the box. Those parts decide whether a rebuild is worth doing. If your armature is scored or your field coils are burned, a kit won’t save the starter. Pull the unit and inspect the commutator and bushings before ordering — a worn commutator or sloppy bushing is the most common reason a fresh kit still won’t crank.

Fitment is the other trap. Kits are not universal. Confirm year, make, model, engine, starter manufacturer, voltage, terminal layout, brush-holder outside diameter, and the OEM or interchange number before buying.

Once the internals are sound and the part number matched, a tested roundup of the best starter rebuild kits saves a lot of cross-referencing.

How Do You Install a Rebuild Kit Safely?

Disassembly, brush seating, lubrication, and torque values must come from your vehicle or starter manufacturer’s service manual — those numbers are application-specific and no generic guide should stand in for them. The electrical safety steps are universal, though.

  1. Disconnect the battery’s negative cable first.
  2. Check replacement dimensions, bolt-hole spacing, and pinion tooth count against the original.
  3. Seat the starter in the housing and hand-tighten the mounting bolts before torquing them to spec.
  4. Connect the main positive cable to the large B+ terminal and the ignition wire to the small S terminal.
  5. Tighten the terminal nuts gently — overtightening cracks the plastic solenoid cap. Refit the rubber covers.
  6. Never crank continuously for more than 10–15 seconds.

Swapping B+ and S is the classic mistake, and it can fry the solenoid the moment you turn the key.

Is a Rebuild Kit Cheaper Than a New Starter?

Usually, yes — by a wide margin. The kits above list between roughly $31 and $41, while a complete replacement starter for most motorcycles, ATVs, and older trucks runs several times that. Prices are retailer listings and they move, so treat them as a ballpark, not a quote.

The rebuild only pays off when the rest of the unit is healthy.

Common Questions

Can I rebuild a starter without any mechanical experience?

Solenoid contact kits are beginner-friendly — basic hand tools and careful attention to contact position are usually enough. Brush and bearing kits demand more: you’ll need to press out bushings, seat brushes, and check the commutator. If you’ve never opened a motor, start with a contact kit or have a shop bench-test the unit first.

How do I know which kit fits my starter?

Identify the starter manufacturer and part number stamped on the housing, then match voltage, brush-holder diameter, and terminal layout. Cross-check the OEM or interchange number the seller lists. Year, make, model, and engine alone are not enough — the same vehicle can ship with starters from more than one supplier.

Why does my starter still click after a rebuild?

A persistent click usually means a weak battery, a loose ground strap, or contacts installed in the wrong positions. Check battery voltage and clean every connection before opening the starter again. If those are fine, the solenoid plunger or the armature is likely worn past the point a kit can fix.

Sources

Scroll to Top