What Is an AIO Liquid Cooler and How Does It Work? | Sealed Loop Basics

An AIO liquid cooler is a sealed, factory-filled CPU cooler that moves heat from the processor to a radiator using a pump, coolant, and fans, with no refilling required.

AIO stands for all-in-one, and the name is literal: the cold plate, pump, tubing, radiator, and fans arrive as a single closed unit. The liquid inside never gets topped off, replaced, or drained during normal use. That sealed design is why these coolers have become the default choice for anyone who wants liquid cooling without building a custom loop from individual parts.

The short version: heat leaves the CPU, rides the coolant to a radiator, and gets pushed into the air by fans. Everything below explains each stage and the install details that decide whether the system runs quietly for years or starts gurgling within weeks.

What Parts Make Up an AIO Cooler?

Five components do the whole job, and each one has a single clear role in the heat-transfer loop.

  • Cold plate: presses against the CPU with thermal compound between the surfaces and pulls heat out of the processor.
  • Pump: pushes coolant around the closed loop continuously.
  • Tubing: carries warmed coolant to the radiator and cooled coolant back to the cold plate.
  • Radiator: metal fins that hand the coolant’s heat off to the surrounding air.
  • Fans: force air through those fins so the heat actually leaves the case.

Because the loop is sealed at the factory, there is no reservoir to check and no coolant to mix. Routine maintenance mostly amounts to clearing dust from the radiator fins and fans.

How Does the Heat Actually Get Out?

The cycle runs in one direction and never stops while the PC is on. Heat travels from the CPU into the cold plate, the pump moves the warmed coolant through the tubing to the radiator, and fans push air across the fins so the heat escapes into the room. The cooled liquid then returns to the cold plate and the loop repeats.

That continuous circulation is the whole trick. A tower air cooler dumps heat into a metal block and relies on case airflow to carry it off; an AIO physically relocates the heat to a radiator mounted at the edge of the case, which is usually where fresh air enters or exhaust leaves.

What Radiator Size Do You Need, and Will It Fit?

Consumer AIO sizes are named by radiator class — 120 mm, 240 mm, and 360 mm — matching one, two, or three 120 mm fans. A larger radiator generally gives more surface area for heat to dissipate, which helps with hotter processors.

Fitting one comes down to more than the radiator’s length. Corsair’s own buyer guidance points to case radiator clearance, and the practical checks are just as important: RAM height under the mounting area, motherboard heatsink clearance, and enough fan and pump headers on the board. Socket support is a separate question, so confirm the exact cooler lists your CPU. Current Intel sockets include LGA 115x, LGA 1200, and LGA 1700; AMD builds use AM4 and AM5. Once you know your size, a tested shortlist of water cooling AIO picks by radiator size saves a lot of cross-checking.

How Do You Install One Without Causing Problems?

Installation follows a fixed order, and the mistakes that matter are almost all mounting errors rather than part failures. ASUS’s official guidance is worth following closely here.

  1. Verify the cooler supports your CPU socket and that the case fits the radiator’s exact dimensions.
  2. Fit the correct socket backplate, retention bracket, and standoffs.
  3. Apply thermal paste unless the cold plate ships with paste pre-applied.
  4. Set the pump block on the CPU and tighten the screws evenly in a diagonal pattern, as ASUS specifies.
  5. Mount the radiator and fans, then connect pump, fan, power, and lighting cables per the manual.
  6. Confirm the pump and fans are spinning in firmware or the maker’s control software before sustained use.

Radiator orientation decides long-term reliability. ASUS recommends top mounting to keep air bubbles away from the pump. If you front-mount instead, put the tubes at the bottom and keep the radiator’s top edge above the pump block.

Common failure points, in rough order of frequency: a radiator that does not fit the case, overlooked RAM clearance, the wrong socket bracket, an unconnected pump header, protective film left on the cold plate, too much thermal paste, and fan and pump headers swapped. Never open or refill a sealed AIO unless the manufacturer publishes service instructions for that model.

Sources

Scroll to Top