A Z87 marking means the eyewear was built and tested to meet the ANSI/ISEA Z87.1 standard for occupational eye and face protection.
That little stamp on the temple or lens is a standard number, not a protection level — and the difference matters the moment a hazard is impact rather than dust. OSHA’s eye and face protection rules rest on this standard, so reading the marking correctly is the whole game when you’re buying protective eyewear for a shop, a range, or a lab.
The standard’s full name is Occupational and Educational Personal Eye and Face Protection Devices. It sets out design, performance, testing, marking, selection, care, and use requirements for protection against flying fragments, chemical splashes, optical radiation, and dust. It’s a consensus standard, not a law itself — OSHA incorporates specific editions into particular regulations.
Z87 vs. Z87+: What’s the Difference?
Z87 alone is the basic-impact marking. High-impact performance requires a separate “+” indicator, either as a plus sign on the lens or as Z87+ on the frame or complete spectacle assembly.
This is the single most misread part of the whole system. Plenty of frames carry a plain Z87 stamp and nothing more — that’s a basic-impact protector, not a high-impact one. If the job involves grinding, chipping, or any hazard where a lens could take a fast hit, look for the plus.
- Z87 — basic-impact-rated protector marking; says nothing about high-impact performance by itself.
- Z87+ — high-impact-rated protector marking for applicable spectacle assemblies.
- + on the lens — that specific lens passed the high-impact test.
- Z87-2+ — the marking OSHA’s selection chart identifies for high-impact prescription frames.
- D3 — protection against splash, droplets, and sprays.
Filter-lens markings appear where protection from hazardous optical radiation is required. A tinted lens is not automatically a filter lens — OSHA is explicit that tint alone doesn’t qualify a lens for welding, UV, or infrared work unless the lens is marked or documented as a suitable filter.
Which Z87.1 Edition Applies to Your Workplace?
OSHA’s regulations expressly list the 2010, 2003, and 1989 editions of ANSI/ISEA Z87.1 as acceptable consensus standards for covered workplaces. OSHA’s own Field Safety and Health Manual points to the 2020 edition and its marking table, and ANSI has since published a 2025 edition.
A newer standard existing does not mean every OSHA rule has adopted it automatically. If you’re buying for a regulated workplace, check the specific regulation and your purchasing requirements before assuming the latest edition governs your situation.
Fit is the other half of compliance. OSHA requires protective devices to give adequate protection, fit appropriately, and stay in good condition, and the manufacturer must be identifiable on occupational eye and face PPE. Markings can sit on the lens, the frame, the packaging, or the manufacturer documentation depending on the product and edition — so check all four before assuming a pair is unmarked.
Picking the Right Protector for the Hazard
Start with a hazard assessment, which OSHA 29 CFR 1910.132 requires employers to perform before deciding PPE is needed. Then match the protector to what’s actually flying, splashing, or glowing.
For chemical splash and droplets, OSHA’s selection chart points to indirectly ventilated goggles rather than spectacles. For hot sparks or molten metal, spectacles alone won’t cover the face — a face shield worn over them does. Metal frames are a poor choice around electrical hazards, where they can contribute to shock or burn risk.
Readers who wear prescription glasses have three compliant routes: protective eyewear designed to fit over their glasses, prescription-ground safety lenses offering equivalent protection, or safety spectacles with the prescription built into the design. If you want a pair that handles glare on top of impact protection, this roundup of tested Z87 polarized safety glasses covers what actually held up.
For the full regulatory text behind these requirements, OSHA’s 1910.133 eye and face protection standard spells out the employer obligations directly.
| Marking | What It Confirms | Typical Use |
|---|---|---|
| Z87 | Basic-impact-rated protector | General dust and light debris |
| Z87+ | High-impact-rated spectacle assembly | Grinding, chipping, fast-flying fragments |
| + on lens | That lens passed the high-impact test | Replacement-lens verification |
| Z87-2+ | High-impact prescription frame | Rx safety eyewear in impact zones |
| D3 | Splash, droplet, and spray protection | Chemical handling (goggles preferred) |
| Filter shade | Rated against optical radiation | Welding, cutting, UV/IR exposure |
| Manufacturer ID | Maker identifiable on the PPE | Required on all occupational eye protection |
The Mistakes That Void Your Protection
Most failures aren’t manufacturing defects — they’re mismatches between the marking and the hazard.
- Treating Z87 as high-impact proof. Look for the + or Z87+ where impact protection is required.
- Trusting tint for radiation. Only a marked filter lens protects against UV, infrared, or welding radiation.
- Using spectacles for chemical splash. Indirectly ventilated goggles are the correct call.
- Assuming glasses replace a face shield. Spectacles don’t cover the whole face against sparks or molten metal.
- Wearing everyday glasses under the wrong PPE. Over-glasses, Rx safety lenses, or purpose-built goggles are the compliant options.
- Ignoring electrical risk. Metal frames can add shock and burn hazards in electrical environments.
Shared equipment needs cleaning and disinfecting before it’s reissued, and any protector that’s cracked, scratched, or loose has stopped doing its job. Replace it rather than wearing it another shift.
Common Questions
Is Z87 the same as ANSI Z87.1?
Z87 is the marking stamped on compliant eyewear; ANSI/ISEA Z87.1 is the full standard the eyewear was tested against. The marking is shorthand confirming conformance to that standard’s applicable requirements, not a separate certification. It appears on the lens, frame, packaging, or manufacturer documentation depending on the product and the edition it was tested to.
Do Z87 glasses protect against chemical splash?
Not reliably. OSHA’s selection chart directs users toward indirectly ventilated goggles for splash, droplets, and sprays, because spectacles leave gaps around the eyes. A D3 marking on a protector indicates splash and droplet protection, but the style of the eyewear still needs to match the hazard — coverage matters as much as the stamp.
Can I wear my regular prescription glasses under Z87 safety glasses?
Yes, if the outer eyewear is designed to fit over prescription frames, or you use prescription-ground safety lenses that provide equivalent protection, or safety spectacles with the prescription built into the design. Ordinary glasses worn alone under unsuitable PPE don’t meet the requirement. Confirm the fit is secure and doesn’t interfere with other protective equipment.
Sources
- OSHA. “1910.133 — Eye and Face Protection.” Employer obligations, prescription-lens allowances, and protector requirements.
- OSHA. “Eye and Face Protection — Standards.” Lists the ANSI/ISEA Z87.1 editions recognized in OSHA regulations.
- ANSI. “Eyewear Standards and UV Protection.” Covers the Z87.1 standard scope, editions, and marking conventions.