A patio heater thermocouple is a flame-safety sensor that generates a small DC voltage to hold the gas valve open — so testing it means heating the tip and reading millivolts.
The pilot lights, you hold the knob down, you let go, and the flame dies. The steps below walk through it in order, including the readings that mean “replace it” and the causes that look like a bad thermocouple but aren’t.
What the Thermocouple Actually Does
The thermocouple is a two-wire sensor sitting in the pilot flame.
Kill the flame and the voltage collapses within seconds, the magnet lets go, and the valve snaps shut. That’s the whole safety system — it’s why a patio heater won’t run on a pilot that keeps going out, and why you should never bypass it. The CPSC describes the voltage test as reading the sensor with a digital voltmeter while its tip is heated.
The Test, Step by Step
Shut everything down first, then work through the checks in this order so you don’t replace a good part.
- Turn the control knob off, close the propane cylinder valve, and let the heater cool. Work outdoors in open air. Never test near a gas smell or with the safety valve defeated.
- Inspect and clean the pilot assembly. A Tractor Supply patio-heater manual (document 328154-R4) lists dirt around the pilot, a loose gas-valve connection, and a thermocouple that isn’t operating correctly as the three causes of a pilot that won’t stay lit. Check that the tip sits fully inside the pilot flame, the mounting is tight, and the wire connection at the valve is snug.
- Relight and hold the knob 30–60 seconds. That interval comes straight from a manufacturer manual — it’s how long the thermocouple needs to heat before the valve will hold. If the flame dies the moment you release, move to the electrical test.
- Measure DC millivolts. With the gas off and the heater cool, disconnect the thermocouple from the valve. Set a digital multimeter to DC millivolts — not resistance, not AC. Clip one lead to the thermocouple conductor and the other to its terminal, light the pilot, and let the tip heat for 30–60 seconds. Roughly 25–30 mV or higher means the sensor is working. Near zero means it’s dead.
- Reconnect and leak-check. Thread the connection by hand first — no cross-threading, no overtightening — then restore the gas and run the manufacturer’s leak test before you use the heater.
Treat those millivolt figures as a general diagnostic reference. The heater’s own service documentation always controls, and some valves specify a different range.
Why It Might Not Be the Thermocouple
Plenty of “bad thermocouple” diagnoses turn out to be something simpler, and the manuals say so outright. A 48,000 BTU stainless patio heater lists wind, a loose thermocouple connection, and low gas pressure as causes of pilot outage. A 92-inch bronze model adds thermocouple positioning and an activated anti-tip switch to that list.
- Wind or draft blowing the pilot flame off the tip.
- Low fuel pressure — a frosted or nearly empty propane cylinder. The Home Depot Canada guide for model FHGS80001 notes reduced operation below 40°F (5°C).
- Anti-tip switch tripped or its wiring loose, which cuts gas the same way a dead thermocouple does.
- Blocked pilot orifice starving the flame so the tip never gets hot.
Work through those before you spend money on a part. If the pilot won’t stay lit after basic inspection, stop using the heater and have a qualified gas-appliance technician look at it.
Replacing It: What Has to Match
Buy on those five specs, not on “fits most heaters.” If you’d rather compare specific models against your heater’s valve, this rundown of the best thermocouple for patio heater replacements covers the common thread and length combinations.
When you do swap it, keep the gas off until the new unit is threaded in, then leak-test at the connection before the first real burn.
Millivolt Reading Cheat Sheet
| Reading (DC mV) | What It Means | Next Step |
|---|---|---|
| 25–30 mV or higher | Sensor is generating voltage normally | Look at pilot flame, gas pressure, anti-tip switch |
| 15–24 mV | Weak output, often a cold or partly heated tip | Reposition tip in flame, retest for a full 60 seconds |
| Near zero | Thermocouple has failed | Replace with a manufacturer-approved part |
| No reading, tip hot | Broken conductor or bad terminal contact | Check connection, then replace |
Common Mistakes That Waste a Part
Measuring resistance instead of DC millivolts tops the list — the meter setting has to be mV, or the number means nothing. Testing a cold tip is second; the sensor only produces voltage when the flame is actually enveloping it. Third is buying a replacement before checking pilot blockage, wind, low fuel, loose connections, and the anti-tip switch.
One more: continuing to run the heater after a failed leak check, a damaged hose, or a persistent gas odor. Shut it down at that point. Safety lines like that aren’t negotiable, and no pilot flame is worth a gas leak on a patio.
Common Questions
Can I test the thermocouple without a multimeter?
Not reliably. You can confirm the pilot stays lit when the knob is held 30–60 seconds, which tells you the sensor is generating some voltage, but it won’t tell you whether it’s weak or dead.
How long should the thermocouple last?
Most patio heater thermocouples last several seasons of regular use. Heat cycling, dirt buildup on the tip, and corrosion at the valve connection shorten that. If the heater is several years old and the pilot dies on release, the sensor is a reasonable suspect — but check the pilot flame and gas pressure first.
Is it safe to use the heater if the pilot won’t stay lit?
No. The thermocouple exists to shut off gas when the flame goes out, so a heater that won’t hold a pilot is telling you the safety system isn’t working. Stop using it, and if basic cleaning and a verified-good thermocouple don’t fix it, have a qualified gas-appliance technician diagnose the valve and pilot assembly.
Sources
- Tractor Supply Company. “Patio Heater Manual, Document 328154-R4” Lists dirt around the pilot, loose valve connections, and thermocouple failure as causes of pilot outage.
- Home Depot Canada. “FHGS80001 Use and Care Guide” Documents reduced operation below 40°F and thermocouple troubleshooting conditions.
- U.S. Consumer Product Safety Commission. “Tank Top Heater Safety” Describes testing thermocouple voltage with a digital voltmeter and warns about carbon monoxide indoors.