How to Size Well Pump Wire: Ampacity, Voltage Drop, and Distance

Wire size for a submersible pump comes from nameplate full-load amps, voltage, phase, and the one-way distance to the controller.

Two 1-hp submersible motors on the same drop pipe can need different conductors, because starting current, motor design, and run length decide the answer. The routine stays short once you know which numbers matter: the motor nameplate, the tape measure, and the manufacturer’s data sheet.

Skip the inputs and the pump starts, runs hot, trips the overload on the hottest day of the year, and quits well short of its rated life.

What Numbers Decide Well Pump Wire Size?

Five inputs drive every conductor decision: nameplate full-load current, operating voltage, phase, one-way distance to the controller, and installation conditions. Insulation rating, ambient temperature, and conductor count adjust ampacity from those starting points.

  • Full-load amps from the nameplate. Horsepower says how big the motor is; nameplate amperes say what the conductor carries.
  • Voltage and phase. Franklin Water’s 4-inch encapsulated line lists single-phase 230 V at 60 Hz and three-phase 200, 230, 380, or 575 V at 60 Hz.
  • One-way distance from service or controller to motor. Voltage-drop math runs over the whole circuit path, so a two-wire single-phase loop is effectively twice that figure.
  • Installation conditions: wet or dry location, ambient temperature, conduit fill.
  • Controller and cable type the manufacturer requires for that motor.

The manufacturer’s table outranks any generic chart. Franklin Water’s AIM Manual tables list conductor sizes by motor, voltage, and length, and already fold in starting current and the motor’s allowable voltage range — the two things a household wiring chart ignores.

Well Pump Wire Sizing: Limits That Bite During Starting

Ampacity answers the heat question: will this conductor overheat here. Voltage drop answers the performance question: will the motor see enough voltage to start cleanly and run cool. A conductor can pass the first test and fail the second.

For single-phase circuits the common approximation is VD = 2KIL / CM, where K is resistivity, I is load current in amperes, L is one-way length in feet, and CM is circular-mil area. Three-phase work uses the matching phase-voltage relationship plus the manufacturer’s engineering values.

Running drop is the easy half. Starting current runs several times the running load, so a conductor sized only for the run can deliver a start that chatters the contactor, trips the overload, or stalls the motor long enough to damage a winding.

The motor’s tolerance sets the budget. Franklin lists ±10% voltage tolerance at 60 Hz on its 12-inch rewindable motors, and −10%/+6% at 50 Hz on the 10-inch line.

Check What It Protects What Fails Without It
Conductor ampacity Insulation and terminals Overheated cable, failed inspection
Running voltage drop Steady-state motor performance Hot motor, low output, short service life
Starting voltage drop Contactor and start winding Chatter, nuisance trips, motor won’t start
Grounding and bonding People and equipment Shock hazard, ground fault
Wet-location listing Cable jacket downhole Jacket breakdown, insulation failure
Splice method The downhole connection Water intrusion, corrosion
Motor overload protection Winding temperature Repeated trips, burned winding

Where Sizing Jobs Go Wrong

Most undersized feeders come from four shortcuts, cheap to avoid on paper and expensive to fix once the pump is in the hole.

  • Drilled depth used as wire length. What matters is the route from panel or controller to motor, plus the loop for two-wire single-phase.
  • A branch-circuit chart borrowed from household appliances that draw steady current and have no starting surge.
  • Factory leads mistaken for the feeder. Franklin’s 6-inch standard leads come in AWG #8 and AWG #10 depending on horsepower, and high-temperature assemblies run 13 ft to 150 ft with some limits tied to horsepower.
  • No equipment grounding conductor, or cable not listed for submerged service.

Cable construction is part of sizing — a conductor that’s thermally correct but not wet-listed fails at the jacket long before it fails at the copper. If you’re weighing constructions, these tested well pump wire picks cover the submersible-rated options.

Then run the sequence in order:

  1. Write down nameplate amps, voltage, phase, frequency, horsepower, controller type, and the manufacturer-specified cable.
  2. Measure the full route, not the well depth.
  3. Pull the manufacturer’s wire table for that exact motor.
  4. Check ampacity with ambient correction, conductor count, insulation, and terminal limits.
  5. Run drop math for both running and starting current.
  6. If drop is excessive, go up a conductor size, raise motor voltage where equipment allows, shorten the run, or get manufacturer approval. Never move a 230 V motor to 460 V without verifying motor configuration, controller, disconnect, protection, and supply.
  7. Have a licensed electrician or qualified pump installer sign off on grounding, splices, wet-location listing, disconnect, and control-box compatibility.

Common Questions

Is Horsepower Enough To Pick A Pump Cable?

No. Two motors of the same horsepower can draw different full-load current, and starting draw varies with motor design. Size from nameplate amperes and the manufacturer’s table for that exact model, then confirm against ampacity limits and voltage drop. Horsepower only tells you which table to open.

Does The Wire Length Match The Well Depth?

Not usually. What matters is the electrical route from panel or controller to the motor — the drop down the well plus any run across the property. A two-wire single-phase circuit needs the entire loop in voltage-drop math, so the effective path is roughly twice the one-way distance.

How Much Voltage Drop Can A Submersible Motor Tolerate?

No single universal number; the motor’s rated tolerance sets the budget. Franklin lists ±10% at 60 Hz for its 12-inch rewindable motors and −10%/+6% at 50 Hz for the 10-inch line. Work backward from that range, leave headroom for starting current, and confirm the final figure against the manufacturer’s table.

Sources

  • Franklin Water. “Franklin AIM” Supplies the manufacturer’s motor-specific wire-sizing tables, voltage ratings, and installation requirements.

Scroll to Top