Match a storage water heater’s First-Hour Rating to your busiest hour of hot water use, and size a tankless unit by peak flow in GPM at your local temperature rise.
Two ten-minute showers back to back tell you what a tank label never will: the number on the side is storage, not supply. Sizing a water heater is a demand calculation you can do on paper in about fifteen minutes.
The method depends on heater type. Storage tanks are sized by how much hot water they produce in one hour; tankless units by flow rate. Mix them up and you’ll buy the wrong box, however carefully you read the spec sheet.
How Do You Size a Storage Tank Water Heater?
Match the First-Hour Rating (FHR) — gallons of hot water supplied in one hour starting from a full tank — to your peak-hour demand. FHR reflects both tank capacity and recovery rate, so a 50-gallon tank with a weak element can carry a lower FHR than a well-specified 40-gallon unit. The US Department of Energy defines FHR this way and states proper sizing requires matching it to household peak-hour demand. Work in four steps:
- Find your single highest-use hour — not the daily average. Morning routines are the usual culprit.
- List every hot-water use in that hour: showers, baths, faucet draws, dishwasher, clothes washer.
- Add the gallons each consumes. A standard showerhead runs about 2 gallons per minute, so a 10-minute shower is roughly 20 gallons.
- Choose a heater whose label FHR meets or exceeds that total.
Heat-pump water heaters follow the same rule: compare FHR, never storage capacity. Compressor heat input is slower, so the FHR gap between similarly sized tanks can be large.
DOE emergency-replacement guidance offers a cross-check by consecutive showers: one to two 10-minute showers generally map to 50 gallons, three to 65 gallons, and four or more to 80 gallons. These are illustrations, not guarantees — FHR, fixtures, setpoint, and usage patterns still govern.
How Do You Size a Tankless Water Heater?
Size by maximum hot-water flow in gallons per minute and the temperature rise from incoming cold water to target outlet. Both must clear the unit’s rating together — a model rated at a given GPM delivers less flow as the rise grows. DOE identifies 120°F as the target outlet temperature for most uses. From there:
- Get your local minimum incoming-water temperature from the utility or climate data. A Minnesota winter might start near 40°F; a Florida line nearer 70°F.
- Subtract incoming from target for the rise: about 80°F in Minnesota, about 50°F in Florida.
- Add the flow rates of every fixture that could run at once — two showers plus a kitchen faucet is a real scenario.
- Pick a model whose manufacturer performance chart covers that GPM and rise at your climate.
The performance chart isn’t optional fine print — it’s the only place the unit’s real capacity at your conditions appears, and where most tankless sizing goes wrong.
Sizing By Heater Type: What Actually Decides The Number
Each technology answers a different sizing question. Use this table before you shop.
| Heater Type | Sizing Basis | What To Check |
|---|---|---|
| Conventional storage | FHR vs. peak-hour demand | Label FHR and recovery rate, not tank gallons |
| Heat-pump storage | FHR vs. peak-hour demand | Compressor input and operating mode |
| Tankless | GPM at your temperature rise | Manufacturer performance chart for your climate |
| Solar | Collector area plus storage volume | Region-based collector area rules of thumb |
Solar water heating has its own math: DOE guidance describes sizing collector area and storage volume to household need, with contractor rules of thumb using about 20 square feet of collector for each of the first two occupants, then 8 square feet per additional person in the Sun Belt or 12–14 square feet per additional person in northern regions.
Once you’ve settled on a type, our roundup of the best water heaters for home use pairs each pick with its rated capacity so you can check it against your peak-hour figure.
Where Do Most People Get Sizing Wrong?
The typical error is buying by nominal gallons without opening the FHR line on the label. The rest cluster into a short list: using average daily consumption instead of the highest-use hour, ignoring back-to-back showers or a dishwasher running in the same window, and sizing tankless on advertised GPM while forgetting incoming-water temperature.
Two cautions: higher tank temperatures can stretch usable mixed-water volume, but DOE replacement guidance notes elevated temperatures require a properly installed mixing valve and scald protection. And installation must match the heater’s fuel and electrical requirements, venting, clearances, water pressure, drainage, and local plumbing code — sizing documents cover capacity, not the installation review your jurisdiction requires.
Read the DOE’s heat-pump water heater snapshot for the full FHR definition before comparing models.
Common Questions
Is a bigger tank always the better choice?
No. A larger tank raises storage volume but not necessarily FHR, which is what limits supply. Oversizing costs more upfront and wastes standby energy. Match FHR to your peak hour and let tank size follow.
Can I size a tankless unit using the same gallons figure as a tank?
Not directly. Tankless heaters are rated in gallons per minute at a stated temperature rise, so peak-hour gallons don’t transfer. Convert simultaneous fixture flow to GPM, then confirm the model’s chart covers that flow at your local rise.
What if everyone in my house showers in the same hour?
Then that hour governs. Add every shower, plus any faucet, dishwasher, or washer running at the same time, and size to that total rather than a daily average.
Sources
- US Department of Energy. “Heat Pump Water Heaters Technology Snapshot” Defines First-Hour Rating and requires matching it to peak-hour demand.
- US Department of Energy. “Measure Guideline: Tankless Water Heating” Supports flow-rate sizing, temperature rise, and the 120°F target outlet temperature.
- US Department of Energy. “Water Heater Replacement Guidance” Covers consecutive-shower sizing illustrations and mixing-valve scald protection.