Size an electric motor from the duty cycle: continuous, peak, and RMS torque must fit its speed-torque curve, not horsepower alone.
Nameplate horsepower says nothing about torque at the speed where the load bites, so a motor that looks generous on paper can stall on a cold start. Five numbers settle sizing: torque, speed, acceleration, inertia, and duty cycle. Skip them and you get nuisance trips, hot windings, or a gearbox howling under a load it was never built to carry.
Sizing An Electric Motor: The Step Order That Works
Start with the mechanical duty, then work outward to torque, speed, and the motor. A load profile — torque and speed plotted against time — is the document every later decision hangs on, recording startup, acceleration, steady run, deceleration, reversals, stops, peak loads, duty cycle, and service life. Note whether the load is constant torque, variable torque, or constant horsepower, since each sits differently on the speed-torque curve.
Load torque is force times radius: T = F × r. Add friction, gravity, thrust, belt or chain tension, and gearbox losses. At constant speed, HP = torque in lb-ft × RPM ÷ 5,252 — which is why a small motor moves a heavy load slowly while a large one can stall against something it should out-muscle. Torque at the actual running speed is what matters.
How Do You Calculate Load And Acceleration Torque?
Acceleration torque comes from reflected inertia and how fast the load must speed up: T = WK² × ΔRPM ÷ (t × 307.6), with inertia in lb-ft² and time in seconds.
Total inertia covers the load, couplings, shafts, pulleys, gearbox, and rotor. Belts and gears cut reflected inertia by the square of the speed ratio, so 4:1 leaves one-sixteenth at the shaft. Aim for reflected inertia near motor inertia, under about five times where hardware allows.
Add acceleration, friction, gravity, and process torque with correct signs for each part of the profile, then recalculate after a candidate motor is picked — rotor inertia changes the acceleration term, making sizing iterative. RMS torque across the duty cycle sets continuous loading; peak torque goes against the peak or overload rating, including overload duration.
The same sequence appears in ABB’s three-step sizing method, with worked curves attached.
Matching The Motor, Drive, And Environment
A motor that clears the torque math can still fail on the supply, drive, or room. Apply roughly 30% margin on maximum torque during dimensioning, and about 50% when plotting total torque against velocity on the speed-torque curve. More buys nothing: oversizing dulls efficiency, raises cost, and complicates control.
The drive needs its own sizing pass. A variable-frequency drive or servo amplifier must match motor voltage, current, overload duty, control mode, braking needs, and switching frequency, and the motor needs inverter-duty insulation wherever drive output is PWM.
Environment trims usable torque. Ambient temperature, altitude, humidity, dust, washdown, hazardous-location classification, enclosure type, cooling, and mounting orientation all affect the continuous rating; manufacturer derating curves are the only reliable source for how much.
Continuous, intermittent, stall, and breakdown torque come from manufacturer ratings, never from dividing nameplate horsepower. US federal motor-efficiency rules reference NEMA MG 1 breakdown-torque values, putting the standard and nameplate in the same conversation.
| Check | What To Confirm | Missed, It Costs You |
|---|---|---|
| Supply match | Nameplate voltage, phase, and frequency against the available supply | A rewind or a replacement motor |
| Drive pairing | Current, overload duty, control mode, braking, and switching frequency | Nuisance trips and insulation failure |
| Environment | Ambient temperature, altitude, dust, washdown, enclosure, and cooling | Derated torque and short winding life |
| Mechanical fit | Shaft, flange, bearing, coupling, gearbox, and brake | Vibration, wear, and misalignment |
| Thermal ratings | Continuous, peak, and stall torque from manufacturer data | Overheating on ordinary duty |
Once torque figures and supply are fixed, the shortlist gets short fast. Hardware built for a given voltage and frame carries most of the remaining risk, and a tested worldwide electric motors roundup beats a blank catalog search.
Run the order once and the choice stops being guesswork: load profile, load torque, acceleration torque, reflected inertia, RMS and peak checks, speed-torque and thermal limits, then drive, environment, and margin.
Common Questions
Can I Size A Motor By Horsepower Alone?
No. Horsepower describes torque at one rated speed, so it hides what happens at startup, at low speed, or during brief overload, and two motors with identical horsepower can behave very differently on the same load. Pull continuous, peak, stall, and breakdown torque from manufacturer data and check them against your load profile.
How Much Extra Torque Should I Leave In Reserve?
About 30% above calculated maximum torque while dimensioning, and roughly 50% when plotting total torque against velocity on the speed-torque curve. Use verified manufacturer data and your own duty cycle. Pushing far past that range costs efficiency and money and can make precise control harder.
Does Ambient Temperature Change The Motor I Need?
Yes. Hot air, high altitude, sealed enclosures, and blocked cooling all reduce continuous torque, so the same frame may be fine in a climate-controlled room and marginal on a plant floor. Manufacturer derating curves show how much capacity disappears at a given temperature and altitude. Size against the derated figure, not the catalog headline.
Sources
- ABB. “3 Steps to Sizing Motors and Drives” Supports the load-profile, torque, inertia, and margin sequence.
- Kollmorgen. “Application Sizing Guide” Covers RMS and peak torque checks and reflected inertia limits.
- WEG. “Specification of Electric Motors” Explains thermal loadability, speed-torque curves, and environmental derating.