How to Replace a Whirlpool Dishwasher Pump | Match The Model

Whirlpool dishwasher pumps are model-specific, so the swap starts with the exact model number and the matching drain-pump or wash-pump procedure.

Standing water and weak spray are two different repairs: the first points at the drain pump, the second at the wash-pump assembly. Before ordering any part, match the exact model number — pump bodies, harnesses, and fasteners change between model families.

That number sits on a plate on the inner door edge or front frame. Whirlpool’s published procedure covers 18- and 24-inch ADA dishwashers by name; a plate from another family means different access, wiring, and possibly a different pump.

Replace A Whirlpool Dishwasher Pump: What Has To Match

Whirlpool builds pumps to a model, not a brand, and recommends FSP factory-specified parts because they are made to fit and function. No universal pump drops into every Whirlpool, Maytag, Amana, or KitchenAid tub.

US owners can call Whirlpool’s Customer Interaction Center at 1-800-253-1301 or use an authorized service center with the full model number. Comparing listings first helps — these tested Whirlpool dishwasher pump replacements cover the most common part numbers, but your plate decides which fits.

Drain Pump Or Wash Pump: Which One Failed?

The drain pump moves wastewater out through the drain hose; the wash-pump assembly circulates water through the spray arms. Standing water with a low hum means the first; weak or missing spray means the second.

Clear the drain path before buying anything: the drain hose, sump check-valve area, household plumbing, garbage-disposal connection, and the knockout plug inside a new disposal. An unpunched knockout behaves exactly like a dead pump.

A reading well outside that points at the pump or motor; an open circuit means checking the harness and connections first. Whirlpool Service Manual W11187658 carries the full chart.

Component What It Does What To Know Before Ordering
Drain pump Pushes wastewater out the drain hose Harness unplugs first; body turns a quarter turn counterclockwise
Wash-pump assembly Drives water up to the spray arms Outlet hose, inlet hose, ground wire, rubber support all come off
Pump O-ring Seals the drain pump to the sump Must sit fully inside the new pump before it goes in
Factory hose clamps Hold the wash-pump hoses in place Not reusable — fit new screw-type clamps instead
Drain hose Carries water to household plumbing Check for kinks and clogs before blaming the pump
Sump check valve Blocks backflow into the tub Clear debris here before condemning a pump
Disposal knockout plug Opens the dishwasher port on a new disposal A plug left in place stops draining cold

Removing The Old Pump And Seating The New One

Power off at the breaker, water valve closed, towel under the drain hose, and the unit out of the cabinet first. Whirlpool labels pump work an electrical-shock hazard and requires the power disconnected.

Drain pump removal:

  1. Pull the cutlery basket and lower rack, slide the dishwasher out, tip it onto its back.
  2. Remove the single base-cover screw and lift off the cover.
  3. Unplug the drain-pump wire harness.
  4. Grip the pump and turn it one-quarter turn counterclockwise — opposite the arrow on the sump — then lift it free.
  5. Seat the O-ring in the new pump, reconnect the harness, refit the cover, and stand the unit back up.

The wash-pump assembly uses a separate sequence: outlet clamps and hose, inlet clamps and hose, wiring harness, ground wire, rubber support, then the assembly. Factory hose clamps are not reusable, so fit new screw-type clamps on the drain pump, wash-pump assembly, water-inlet valve, or sump; they ship separately.

Installation rules: level front to back and side to side, power cord clear of the motor and lower tub, and a grounded three-prong outlet. You’ll know it worked when the tub empties completely on a drain cycle and the spray arms turn under steady pressure.

Common Questions

Can A Pump From One Whirlpool Model Fit Another?

Usually not. Whirlpool designs pumps around a specific model, and the procedure published for the 18- and 24-inch ADA dishwashers may not transfer to another Whirlpool family, let alone Maytag, Amana, or KitchenAid. Pull the complete model number from the door-edge plate and confirm the part against it before ordering — harnesses, clamps, and fasteners change with the pump.

What Does A Replacement Pump Cost?

Whirlpool doesn’t publish pump pricing, and the figure shifts with model and part number, so no single number holds. Get a quote from the Customer Interaction Center at 1-800-253-1301 or an authorized service center using your model number, then weigh it against a new dishwasher.

Why Is There Still Water In The Tub After A New Pump?

Go back to the drain path. A kinked or clogged drain hose, debris around the sump check valve, a blocked household drain, or the knockout plug left inside a new garbage disposal will stop a healthy pump from emptying the tub. Clear those, run a drain cycle, and check the pump wiring only if water still stands.

Sources

Scroll to Top