Pip-Boy Phone Case Sizing and Compatibility Guide | Measure Before You Buy

Two products share the name: the molded plastic Pip-Boy Edition holder Bethesda shipped in November 2015, and a decorative phone case using the same branding. Their sizing rules are unrelated, and mixing them up is how people force phones into a replica built for a 2014 handset.

What Fits Inside The Original Pip-Boy Edition?

The iPhone 6 (138.1 × 67.0 × 6.9 mm) clears all three. The iPhone 6 Plus (158.1 × 77.8 × 7.1 mm) exceeds both height and width and does not fit at any angle — the comparison behind most replica complaints.

Pip-Boy Phone Case Compatibility: Which Phones Actually Go In

Fit is decided by three measurements, never by brand or OS; both iPhone and Android were supported within the cavity limits.

Measure the phone as it will be worn — screen protector on, slim case on if you’ll keep it. A 0.5 mm difference is what turns a snug fit into a stuck phone.

Phone Dimensions (mm) Fit In Pip-Boy Edition
iPhone 4 / 4S 115.2 × 58.6 × 9.3 Fits — foam insert needed
iPhone 5 / 5S 123.8 × 58.6 × 7.6 Fits — foam insert needed
iPhone 6 138.1 × 67.0 × 6.9 Fits — smallest insert or none
Samsung Galaxy S3 136.6 × 70.6 × 8.6 Fits — foam insert needed
Samsung Galaxy S4 136.6 × 69.8 × 7.9 Fits — foam insert needed
Samsung Galaxy S5 142.0 × 72.5 × 8.1 Marginal — foam may change the fit
iPhone 6 Plus 158.1 × 77.8 × 7.1 Does not fit

The Galaxy S5 is the edge case: a hair over the cavity on height and width, with varying owner reports — some get it in with the foam, and it may leave more screen edge exposed. Treat it as a maybe.

The companion app runs fine on a phone that never goes near the holder, so a too-large handset costs you the prop, not the inventory screen.

For a wearable you can actually wear with a current phone, a purpose-built replica case is the realistic route — our roundup of Pip-Boy phone cases that fit modern handsets covers the shells sold today.

What About Modern Pip-Boy-Branded Cases?

Current marketplace “Pip-Boy” cases are standard protective shells with branding printed on — not the 2015 wearable, and their fit lists are seller-specific.

Those ranges belong to those sellers. Another listing may cover different models, so check the exact model line on the page you’re buying from rather than assuming the branding implies a standard fit.

Where People Go Wrong

Most damaged replicas and returned cases trace back to four mistakes.

  • Ordering by phone name instead of dimensions. “iPhone 6” fits; “iPhone 6 Plus” does not. The name carries no sizing information.
  • Forgetting the installed case. A phone that fits bare can be 2 mm too thick with a rugged shell. Measure what you’ll keep on the phone.
  • Skipping the foam. Without the right insert, a phone that technically fits will shift, press its own buttons against the plastic, and can end up scratched.
  • Forcing it. If the phone needs pressure to seat, stop. A bowed screen or pinched side button is the usual result.

The original unit shipped in 2015 and is not a universal modern holder; its fixed limits are the phone’s problem to meet.

Common Questions

Can I use the Fallout companion app without the wearable?

Yes. The app links to your game for inventory, perks, holotapes, and related screens, and runs on a phone that never goes into the holder. Plenty of players use it on a large handset that would never fit the 2015 replica.

Will a phone in a protective case still fit the original Pip-Boy?

Usually not, and it depends on the case. The cavity is 10.2 mm thick at its limit, so a phone measuring 8 mm or more before adding a shell is already close. Measure with the case on and compare to 141.2 × 71.6 × 10.2 mm.

Do the foam inserts make a difference?

They do. The inserts hold a smaller phone steady inside a cavity built to a fixed size. Running without the right one leaves the phone loose, and loose means it shifts against the plastic and can press its own buttons.

Sources

Scroll to Top