How to Mount a Trailer Gas Can Holder Securely? | Frame First, Never Skin

Mounting a trailer gas can holder securely means bolting it through a load-bearing rail, frame member, or wall support with every supplied fastener — thin panel skin will tear free once a full can starts bouncing.

Attach that weight to unsupported sheet metal and you get a cracked panel, a lost can, and a fuel spill behind your trailer. Getting it right takes one drill, a look at the trailer’s structure, and about an hour.

The steps below follow the mounting locations the holder makers specify, plus the fit checks that prevent most failures. A quick comparison of real holder options is worth a look before you buy.

What Makes a Good Mounting Point on a Trailer?

A load-bearing element — not panel skin — is the only acceptable attachment point. On an open trailer, that means the top rail or a frame crossmember; on an enclosed trailer, the wall supports or the upper metal runner.

If you can flex it with a firm push of your thumb, it cannot hold a loaded gas can. Enclosed trailer skins, aluminum siding, and plastic panels all fall into that category. The steel racks sold for this job list rails and wall supports as the intended mounting surfaces.

Check the reverse side before you drill. Wiring, brake lines, and structural tubes hide behind panel surfaces, and a drill bit through a brake line turns a small project into a repair bill.

Step-by-Step: Mounting the Holder So It Stays Put

Fitting first and drilling second is the difference between a clean install and a holder full of misaligned holes.

  1. Match the holder to the can. Compare the can’s shape, dimensions, capacity, and weight against the holder spec. Not every “5-gallon” can shares the same footprint, so measure the actual can rather than trusting the label.
  2. Choose the structural attachment point. Top rail or frame member on open trailers; wall supports or the upper metal runner on enclosed ones.
  3. Position it clear of hazards. The can must stay upright and never touch tires, suspension, exhaust, sharp edges, cargo, or the loading path. It also needs to come out without spilling.
  4. Mark every hole, then check behind the surface for wiring, plumbing, structural members, and clearance.
  5. Install every supplied fastener. Where the structure allows, use through-bolts with washers and locknuts; otherwise use manufacturer-approved structural screws. Tighten firmly, but don’t crush thin panels.
  6. Engage all restraints — straps, retaining bars, clamps, pins, or locks.
  7. Shake-test it, empty and loaded. Look for movement or flexing, then recheck every fastener after the first trip and periodically after that.

If the holder came with no hardware, oversized fasteners are safer than undersized ones, and a backing plate spreads the load across a wider area of the rail.

Holder Sizes, Capacities, and What They Cost

Steel racks in the 35-pound capacity class cover most one- and two-can setups, with side-mount bottle holders serving larger cylinders.

Holder Capacity & Fit Price
Gas Can Rack LT30 35 lb; one 5-gal or two 2.5-gal rectangular polymer cans; 19 × 12.5 × 4.5 in $78.95
Locking Gas Can Rack LT32 35 lb; one 5-gal Blitz can or two 2.5-gal rectangular polymer cans; 15.5 × 10 × 10 in; hardware and lock included $79.95
Side-Mount Bottle Holder Bottles 8.3–10.6 in diameter; back plate, base plate, adjustable clamp, and hardware included; 3-year warranty $181.35

Both steel racks mount to an open trailer’s top rail or an enclosed trailer’s wall supports. If you’re still deciding which style fits your setup, this roundup of tested trailer gas can holders compares the real-world options side by side.

The 35-pound rating is worth a second look: a full 5-gallon can of gas runs close to 40 pounds, so check your total weight against the rack’s stated capacity. The side-mount holder’s dimensions come from Dometic’s gas and propane bottle holder product page, which lists the full fitting hardware.

Where Most Installs Go Wrong

Both are avoidable before the drill comes out.

  • Panel skin instead of structure. Fasteners pull straight through thin aluminum once the load starts bouncing. Find the rail.
  • One fastener doing all the work. Use every hole the holder provides.
  • Friction instead of restraint. A can held only by gravity will walk loose; straps and clamps exist for a reason.
  • Skipping the fit check. Measure the can against the holder spec before drilling anything.

Common Questions

Can I bolt a gas can holder to the trailer floor instead?

Yes, but only if the floor section is reinforced and load-bearing. Standard plywood or thin aluminum decking will crack under a loaded can. Add a metal backing plate across the underside, use through-bolts with washers and locknuts, and confirm nothing sits beneath the drill path.

Do I need a locking holder?

A lock adds theft protection and keeps the can from shifting if a strap loosens. The LT32 rack includes a lock and mounting hardware at about the same price as the non-locking LT30. If your trailer sits unattended in public lots, the extra security is worth it.

How often should I recheck the mounting bolts?

Check every fastener after the first trip, then a few times per season and before any long haul. Vibration loosens hardware gradually, and a shake-test with the holder loaded takes about 30 seconds. Add a check whenever you notice rattling or unusual movement.

Sources

Scroll to Top