How to Install a Rear View Camera on a Travel Trailer | DIY

A trailer rear camera mounts square to the back wall, pulls 12-volt power from the marker lights, and pairs with its own monitor before you tow.

Most trailer cameras fail on aim, not hardware — a housing mounted a few degrees off-center throws the guide lines off for good, and a bigger screen never fixes it. Four moves cover the install: square the mount to the back wall, pull 12-volt power from the marker lights, seal every penetration, and pair the monitor before you tow.

What changes between kits is the mounting surface and power source. A trailer with a factory camera connector is close to plug-and-play. Without one, you tap a 12-volt circuit and drill through exterior walls — where a careful install separates from a leaky one.

Where Should The Camera Go On A Trailer?

The camera goes horizontally centered on the rear wall, square to the surface, aimed straight down the trailer’s centerline. Even slight rotation produces false guide lines.

Rear wall or roof both work, provided the camera sits flat with no left-right yaw.

  • Wipe the bracket and mounting area with isopropyl alcohol; let both dry completely.
  • Keep the lens clean and out of pooled water; a dirty lens can shut down some camera functions.

Rear View Camera Installation On A Travel Trailer: Where The Power Comes From

Most trailer kits pull power from the marker lights, so the running lights must be on for the camera to work.

A dedicated trailer-camera connector, where the truck supplies one, skips the tapping — the harness plugs in and power comes from the truck side.

The Phillips REAR-VU 78-1204 installation guide spells out voltage and lead colors.

  • Cut power before splicing or drilling, and check running and brake lights before driving.
  • Seal every hole through the shell with a grommet and exterior-grade sealant.
  • Run the harness clear of the exhaust, suspension, sharp edges, and moving hitch parts.

Flipping the running lights on should light the monitor with a live feed — confirm before sealing.

Matching A Monitor To Your Truck And Camera

Pairing happens on the monitor, never the camera. If the screen shows no feed, or you mounted a camera the bundle didn’t include, the Furrion Vision S+ manual directs you to the monitor’s Pair with a Camera routine; when it takes, the feed fills the screen.

A factory dash display is separate. Showing a trailer camera there takes three things at once: the matching accessory camera, the trailer-camera port on the truck, and vehicle-specific feature support. With any missing, use the dedicated monitor.

Furrion’s Vision S+ bundles differ mainly by screen size and camera count. Retail listings, which move:

Vision S+ Kit Listed Price What It Covers
5-inch monitor with rear Sharkfin camera, FOS5HTASF $475 Single rear view on the smaller screen
7-inch monitor with rear Sharkfin camera, FOS7HTASF $505 Same single view on a larger screen
7-inch single camera observation system $479 Standalone kit with a 7-inch display
5-inch monitor with side cameras and rear Sharkfin camera, FOS5HTAEN $810 Rear view plus both blind sides
7-inch monitor with side cameras, rear camera, and LED marker lights, FOS7HTAPM $1,010 Four-camera coverage with marker lights built in

Prices are retailer listings and do change, so confirm the model number before ordering.

An hour comparing brands pays off — our tested travel trailer rear view camera roundup lines up the kits worth mounting.

The order holds across brands: aim, power, seal, pair. If the trailer’s wiring is unknown or the wall construction isn’t obvious, hand the job to a shop — this can mean tying into a 12- or 24-volt system and cutting exterior walls. Treat the screen as an aid; mirrors, a spotter, and a slow reverse still do the real work.

Common Questions

Can The Camera Feed Show Up On The Truck’s Factory Screen?

Sometimes, but only when three things line up: a matching accessory camera, a trailer-camera port on the truck, and vehicle-specific feature support for trailer views. A truck with a tow package still may lack the port or software. If any is missing, use the kit’s dedicated monitor on the dash.

Do The Running Lights Have To Be On For The Camera To Work?

On marker-light-powered kits, yes. The Phillips REAR-VU 78-1204 needs at least 10 volts at the light and carries no battery, so the tow vehicle’s running lights must be on. Kits wired to a dedicated trailer-camera connector skip that step, since power comes from the truck side.

How Do You Know The Aim Is Right Before Tightening Everything?

Power the camera up first and watch the monitor while someone stands behind the trailer. The rear wall should sit square in the frame, with guide lines parallel to the trailer’s sides. Rotate the housing until both hold, then drive the screws and snap on the cover. Aiming after the screws are in means filling holes.

Sources

Scroll to Top