How to Choose a Table Saw for Woodworking | Match Saw to Stock

Pick a table saw by matching cut depth and rip capacity to the stock you actually cut, then confirm the fence, safety gear, and blade size meet the manual’s specs.

A 15-amp motor tells you nothing about whether the blade will clear a 2-inch oak plank at a 45-degree bevel, or whether the fence rail reaches far enough to break down a 4 × 8 sheet. Two 15-amp saws can differ by an inch of cut depth and six inches of rip capacity.

The rest — stand compatibility, blade size, corded versus cordless — is where buyers get burned after the sale, so those get covered too.

What Cut Depth Do You Actually Need?

Match the saw’s maximum cut depth at your most common bevel angle to your thickest stock, because depth drops sharply as the blade tilts. DEWALT’s manual for the 8¼-inch DWE7485 lists 2 9/16 inches at a 0° bevel but only 1¾ inches at 45°.

That gap matters. A 2-inch-thick benchtop glue-up passes fine at 90°, but bevel the same board and you’ll need two passes — or a bigger saw. The 10-inch DWE7491RS cuts 3⅛ inches at 0° and 2¼ inches at 45°, per its own published manual.

Measure your thickest recurring stock before you shop. If you mostly build cabinets from ¾-inch plywood and 1½-inch framing, an 8¼-inch saw clears everything. If you mill thick hardwood or cut deep bevels, the 10-inch capacity is the difference between one pass and two.

How Much Rip Capacity Should You Buy?

Rip capacity should exceed the widest cut you make regularly, measured from the blade to the fence’s far position.

For most shop work — ripping cabinet sides, trimming shelves, squaring panels — 24 inches covers it. Full sheet breakdown and wide casework push you toward a saw with a longer rail. The tradeoff is footprint: bigger capacity means a larger table and, usually, a heavier machine that stays put.

Spec DWE7485 (8¼ in) DWE7491RS (10 in)
Motor / power 15 amp corded 15 amp corded
No-load speed 5,800 rpm 4,800 rpm
Cut depth at 0° 2 9/16 in 3⅛ in
Cut depth at 45° 1¾ in 2¼ in
Rip capacity 24.5 in Longer rail for sheet goods
Table size 19 × 19 in 21⅞ × 26⅜ in
Bevel range −2° to 47° left 0° to 45° left
Listed weight Jobsite-portable Over 55.2 lb

Which Fence, Power Source, and Safety Gear Matter Most?

A rigid fence that adjusts fast and locks square is the single biggest accuracy upgrade on any saw. DEWALT identifies the DWE7485’s rack-and-pinion telescoping fence as its primary fast-adjustment and accuracy feature — a fence that shifts under pressure ruins every cut downstream.

Power source splits the field cleanly. The DWE7485 is corded at 15 amp and needs a dedicated circuit. The cordless DCS7485 runs on DEWALT’s 60V MAX battery platform, tool-only, with a brushless motor at 5,150 rpm — DEWALT notes 60V MAX is maximum initial voltage without workload and nominal voltage is 54 volts. Battery and charger sell separately, so budget for them.

Confirm what ships in the box rather than assuming. The DWE7485 includes a blade brake, power-loss reset, push stick, miter gauge, anti-kickback pawls, riving knife, and modular guard system. Buying a saw stripped of those means buying them back.

  • Check that the guard and riving knife are included and functional.
  • Verify stand compatibility by exact model — the DWE7485 manual states the DWE74911 stand fits only when bought separately, and brackets from the DWE7491RS stand don’t carry over.
  • Match blades to the manual’s spec: DEWALT lists 8¼-inch blades with a 2.40-mm kerf for the DWE7485 Type 3, paired with a 0.087-inch riving knife.

When you’re comparing full kits side by side, this roundup of tested table saws for woodworkers lays out stands and bundled accessories by model. DEWALT’s DWE7485 instruction manual is the source for every capacity figure above — read it before you buy, because specs shift between types and regions.

What Should You Check Before Swiping the Card?

Run this short sequence and you’ll avoid the five most common purchase errors: buying by amperage, overlooking rip capacity, mismatching the stand, fitting the wrong blade, and cutting material the saw wasn’t built for.

  1. Measure your thickest stock and confirm cut depth at both 0° and 45°.
  2. Match rip capacity to your widest regular cut.
  3. Confirm the fence type and that it locks square.
  4. Verify the guard, riving knife, anti-kickback pawls, push stick, and miter gauge are included.
  5. Check corded amperage or cordless battery and charger requirements.
  6. Look up stand compatibility by exact model number.
  7. Confirm blade size and kerf match the manual’s spec.

The DWE7485’s manual limits it to wood, plastic, and other soft materials — not metal, cement board, or masonry. Mount any saw on a rigid, stable stand so it can’t shift under an overhanging panel, keep the guard on, wear eye protection and a dust mask, and never leave it running unattended.

Common Questions

Is an 8¼-inch saw big enough for furniture building?

For most furniture work it is. An 8¼-inch saw cuts up to 2 9/16 inches at 90° and 1¾ inches at 45°, which handles ¾-inch plywood, 1½-inch framing, and standard hardwood stock. You only need the 10-inch class when you routinely cut thicker material or deep bevels in one pass.

Can I use any 8¼-inch blade in these saws?

Match the blade to the manual’s listed dimensions, not just the diameter. DEWALT specifies 8¼-inch blades with a 2.40-mm kerf for the DWE7485 Type 3, and the supplied riving knife measures 0.087 inch thick. A blade with the wrong plate or kerf can bind against the riving knife.

Do I need a stand, and will any stand fit?

You need a rigid, stable surface — the manual warns the saw must not move or overturn under large overhanging workpieces. Stand compatibility runs by exact model, though: the DWE7485 takes the DWE74911 stand only when purchased separately, and brackets from other models don’t transfer.

Sources

Scroll to Top