Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
Your Stampede is sitting on the shelf with a cracked or missing shell, and you want it looking right again without a weekend of paint work. Here is the quick answer: the factory-painted Traxxas Rock n’ Roll shell gets you back on the dirt with zero painting. If you want to spray your own colour and save some money, go clear instead. The real decision with any Stampede body depends on three things. Is it pre-painted or blank? Is it trimmed and drilled for the Stampede’s own mounting posts? And will it hold up the next time the truck lands upside down on asphalt?
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Every shell below has been checked for genuine Stampede compatibility rather than generic 1/10 fitment. Each entry spells out the painting, trimming, and mounting work you will actually take on.
This breakdown of the traxxas stampede body covers painted, clear, and licensed shells so you can pick the right one in one pass.
Top Picks



How To Choose The Best Traxxas Stampede Body
A replacement shell is not a universal part. The Stampede has its own body-post spacing (the gap between the four posts that hold the shell) and its own wheelbase (the distance between front and rear axles). A shell shaped for a Slash or a Rustler will not sit right, however good it looks in the listing photo. Before you compare graphics, confirm the shell was built for the Stampede chassis. That single check prevents most fitment returns.
Painted and decorated, or blank and ready for your own spray job
A factory-painted shell arrives trimmed, with the decals already applied. You bolt it on and drive. A clear body is cheaper and lets you choose any colour scheme, but you supply the paint and the masking work. Clear shells ship with a protective overspray film and window masks, so you can cut in the glass cleanly before you lay down colour.
Check the post holes before anything else
Pre-drilled bodies are the fastest route, because the mounting holes already line up with the Stampede’s posts. A shell drilled for a different truck means you measure, mark, and cut new holes yourself. One slip with the body reamer (a tapered cutting tool for enlarging holes) leaves an oval hole that never sits straight. If the listing says the holes are drilled for the Stampede, take that as the head start it is.
How much abuse the shell will take
RC bodies are moulded from polycarbonate, so they flex on impact rather than shattering. Thicker mouldings and a proper clear coat resist spider-cracking at the corners. Thinner shells crease and split after repeated roof landings. You will see the difference first at the body-post corners and around the wheel arches.
Graphics that hide the scuffs
A busy printed design like Rock n’ Roll or a flag strip hides scratches and dirt far better than a plain single-colour shell. Bright graphics also make the truck easier to spot when it tumbles into tall grass. If you plan to bash hard, a loud pattern doubles as camouflage for wear.
Side-by-Side Comparison
| Model | Best For | Finish | Pre-Drilled / Trimmed | Weight | Amazon |
|---|---|---|---|---|---|
| Traxxas TRA3648 Rock n’ Roll★ Best Overall | Bolt-on looks with zero paint work | Factory painted, decals applied | Yes — factory trimmed and applied | 4.48 ounces | Amazon |
| Traxxas 3617 Clear BodyBudget Painter’s Pick | Cheapest route to a custom paint job | Clear, unpainted | Pre-cut; needs painting | 4.9 ounces | Amazon |
| SummitLink Muddy Green Over BlackBest for Bashers | Camo-style basher that hides dirt | Painted, decals applied | Yes — drilled for Stampede | — | Amazon |
| SummitLink Graffiti Pink Pig | A shell nobody else at the track runs | Painted, decals applied | Yes — drilled for Stampede | — | Amazon |
| Pro-Line 2017 Ford F-150 Raptor | Turning your Stampede into a lifted truck | Clear polycarbonate, unpainted | Fresh body — needs paint and trim | 0.1 kg | Amazon |
Detailed Reviews
1. Traxxas TRA3648 Body Stampede
Our pick — 4.5+★ from 200+ verified ratings; the strongest balance of quality and price.
Painted, trimmed, and decalled from the factory — so you bolt it on and drive.
It earns this spot because you can mount it the day it lands. This shell arrives factory painted with the Rock n’ Roll graphics, factory trimmed to the Stampede outline, and with the decals factory applied. No masking tape, no paint cans, no decal-soap water bowl. The 80s-flavoured colour scheme is what wins people over most, and it is bright enough to spot the truck easily when it tumbles into long grass.
At 4.48 ounces versus the Traxxas 3617 clear shell at 4.9 ounces. That lighter lid keeps the centre of gravity a touch lower when you corner hard on pavement. The part number in the factory packaging is 3648, so you have the exact reference if you ever need to match it against a parts diagram.
The honest catch is the value question. You are locked into one graphic scheme, and it costs more than a blank shell plus your own paint. If you enjoy painting, that trade goes against this one. If you do not enjoy painting, the time saved is the whole point.
What arrives ready to run
- Factory painted with Rock n’ Roll graphics — no paint work at all
- Factory trimmed and pre-applied decals, so mounting takes minutes
- 4.48 ounces versus the clear Traxxas 3617 at 4.9 ounces
- Genuine Traxxas part number 3648 for easy parts matching
Where it asks you to compromise
- You are locked into one graphic scheme — no colour choice
- Costs more than a blank shell plus your own paint
- Painted gloss scuffs show up more than on a busy clear-coated blank
Grab this one if: you want the truck looking sharp today and have no interest in masking tape.
Think twice if: you actually enjoy a paint project — the clear Traxxas 3617 costs less and lets you choose the colour.
2. Traxxas 3617 Clear Stampede Body with Decal Sheet
The cheapest way into a one-off colour scheme — if you are willing to hold the spray can.
Buyers single out one thing in their reviews: quality. It is the most-discussed strength in its feedback by a wide margin. This is the genuine Traxxas replacement clear Stampede body, part TRA3617, and it arrives pre-cut, so the outline is already done. You get window masking and a decal sheet in the box, which saves you cutting your own masks out of tape.
What you supply is the paint and the patience. You paint clear polycarbonate from the inside, so thin coats sit on the inner surface and the shell stays glossy outside. At 4.9 ounces versus the painted Rock n’ Roll shell at 4.48 ounces. That penalty is negligible, and you will never notice it on the truck.
Fit lands where it should: the shell is shaped for the Stampede, so the arches clear the wheels and the profile matches the chassis. What it does not do is hide mistakes. A thin spot in your paint or a run at the corner shows through, and you cannot fix it from the outside. If this is your first RC paint job, buy two and treat the first as practice. For an existing airbrush or rattle-can owner, it is the best-value route to a truck nobody else at the park has.
Where the money goes: a pre-cut genuine Traxxas shell with masks and decals, and the painting work is the price of admission.
The honest limit: every flaw in your paint job shows through clear polycarbonate, and it cannot be corrected from outside the shell.
Reach for this if: you want a specific colour and are comfortable with an inside-out spray job.
Look elsewhere if: you want to unbox and drive — the painted TRA3648 does that job with no effort.
3. SummitLink STB-BG-01 Custom Body
Mud-coloured camo that shrugs off dirt, scuffs, and the fact you never clean the truck.
A dark, mottled shell is the smart choice for a truck that lives outdoors. Dirt, grass stains, and hairline scratches simply disappear on this muddy green over black finish, so a badly scuffed basher still looks deliberate rather than abused. It arrives painted with decals on, and the mounting holes are already drilled for the Stampede, so bolt-on is genuinely bolt-on. Run it in wet grass and gravel and the colour choice alone justifies it.
Two things vary depending on your truck. First, this body does not fit a Slash, and SummitLink points you to the measurements in the listing picture — so check your model against them before you buy. Second, on anything other than a Stampede you may need to drill fresh holes and trim the shell a little, because the factory holes are placed for the Stampede’s posts.
Durability is the honest split. Some drivers find it holds up well through normal running, while others have had less luck. Treat that as a fit note rather than a verdict. If you launch your Stampede roof-first off skatepark ramps every session, no polycarbonate shell lasts forever, and this one is no exception. For everyday bashing on grass and dirt, the drilled holes and painted finish make it a very easy swap.
What wins people over: the appearance — it is the most-discussed aspect in its feedback, and dark camo is the smart choice for a truck that gets dirty.
The fit note: durability reports are genuinely mixed, so this suits regular bashing rather than relentless roof-landing abuse.
Pick this for: a dirty-weather basher where the colour hides the wear and the holes already line up.
Skip it for: a Slash or any non-Stampede chassis — SummitLink states plainly that it will not fit, and you would be redrilling.
4. SummitLink STB-PIG-01 Custom Body
A pink graffiti pig on a monster truck — you will never lose it in the grass again.
Half the Stampedes at any park wear the same stock scheme, and this shell fixes that. The graffiti pig artwork is loud and distinctive, and it arrives fully painted with the decals already on. Being pink, it is also the easiest truck to spot when it ends up nose-down in a hedge.
Mounting is sorted for you. The holes are drilled for the Stampede, the body is already painted, and SummitLink states it fits all Stampede versions. You get the same body shown in the listing photos, so there is no surprise pattern waiting in the bag. Fitting it to something else means drilling new holes and trimming slightly, exactly as with any pre-drilled shell.
Two words of caution before you order. The listing is explicit that this body does not fit a Slash, so check your model against the measurements in the listing picture first. If you are not sure which Stampede version you own, confirm that before you buy, because bodies shaped around one chassis do not always sit cleanly on the other.
Choose it for: a Stampede that needs to stand out in a car park full of identical trucks.
One thing to confirm: your exact Stampede version — the shell is drilled and shaped for the Stampede, not for a Slash.
5. SummitLink STB-C-01 Custom Body
Printed graphics already on the shell, with clear windows left open for your own colour work.
Clear areas under the printing are what lift this shell above a plain painted body. Prographix is Traxxas’s pre-printed finish, and the printing leaves those sections open, so you can back them with your own colour to make highlights that pop. Owners appreciate that customisability most, and it sits alongside strong feedback on overall quality. It is a genuine Traxxas part, number 6711X, made for the 4×4 Stampede, so the wheelbase and arches are shaped to that chassis rather than borrowed from elsewhere.
Weight comes in at 0.13 kg, essentially level with the SummitLink flag-strip shell at 0.14 kg, so switching between them will not change how the truck feels. There is no warranty noted on the listing, which is worth knowing up front: if you crack it, you are buying another rather than claiming one.
The one point to plan for is durability. Reports are split between drivers who find it tough and those who say it is no tougher than the stock shell that came on the truck. That is a fair read for any painted body, because the paint layer stiffens the moulding slightly and cracks start at the corners. Buy it for the Prographix look and the custom-accent potential, and treat it as a shell you will eventually replace.
Why painters like it
- Prographix printing with clear areas underneath for your own colour accents
- Genuine Traxxas part 6711X, shaped for the Stampede 4×4 chassis
- 0.13 kg — level with the SummitLink flag shell at 0.14 kg
- Decal sheet included to finish the look
What to plan around
- Durability reports are mixed — some rate it no tougher than stock
- No warranty listed on the product page
- 4×4-specific fitment, so 2WD owners should confirm the body posts line up
The right shell for: a 4×4 Stampede owner who wants printed graphics plan plus room to add their own shade.
The honest catch: no warranty listed, and it is not the toughest moulding in this lineup.
6. Pro-Line Racing PRO347000 Clear Body
Turns the stubborn Stampede silhouette into a lifted full-size pickup.
Its licensed 2017 Ford F-150 Raptor proportions read as a real truck from ten feet away rather than a generic RC blob. Pro-Line moulds it in crisp polycarbonate and shapes it to transform a Stampede into a lifted truck. That makes it the pick for the driver who has stopped caring about stock looks.
At 0.1 kg it is the lightest shell in this group, which is what you want when you are adding a tall truck profile to a chassis that sits high already. It is made in the USA and arrives clear and unpainted, so you supply the paint. Pro-Line lists it as vehicle-specific fitment for the Stampede, so it is built for this chassis rather than adapted to it.
Expect a proper project. A clear body means washing the shell, masking the windows, painting in multiple coats from the inside, and then trimming the wheel arches and mounting holes to suit your posts. That is an evening’s work, and it is the price of getting a look nobody else at the park has. The finished truck looks the part, but the shell arrives as raw material, not a finished body.
The trade you are making: a licensed Raptor body with award-winning proportions and the lightest weight in the lineup at 0.1 kg, in exchange for a full paint and trim session.
What it asks: real model-building effort — wash, mask, paint, and trim before it goes anywhere near the truck.
This is your shell if: you want a genuinely different silhouette and enjoy a proper paint project.
Pass it by if: you want a finished body you can mount the day it arrives.
Know the Specs
Pre-drilled vs blank post holes
The Stampede holds the shell on four body posts, and the holes must line up or the shell sits crooked and rattles. A pre-drilled body has those holes cut at the factory for the Stampede’s spacing, so it mounts straight on. A blank or cross-model shell means you measure, mark, and cut your own, and an oversize hole cannot be fixed, only patched. If the listing says the holes are drilled for the Stampede, that is the fastest route to a truck that sits true.
Painted finish vs clear polycarbonate
A factory-painted shell arrives with colour and graphics already applied, and the decals are usually on. A clear body is moulded in polycarbonate — a tough flexing plastic — and you paint it from the inside, so the colour sits protected under the plastic and stays glossy outside. Clear shells come with a protective film and window masks; you peel the film after painting. Clear lets you choose any colour, painted saves you the work.
Polycarbonate weight and why it matters
RC bodies are measured in ounces or grams because that weight sits at the top of the truck. A lighter shell keeps the centre of gravity lower, so the truck rolls less in hard corners. The bodies here run from 0.1 kg up to 4.9 ounces, and the spread is small enough that most drivers will not feel the difference on a basher. On a race truck, every gram above the chassis counts.
Fitment: Stampede vs Slash vs 4×4
The Stampede has its own wheelbase and body-post spacing, and a shell built for a Slash will not sit right. Several SummitLink bodies state plainly that they do not fit a Slash, so believe the listing. The 4×4 Stampede also has its own shell shapes, so check whether the body was drawn for the 2WD or the 4×4 chassis before you order. Confirm your exact model first; everything else is easy.
Common Questions
Will a Slash body fit my Stampede?
Do I need to drill holes in a clear Stampede body?
How do you paint a clear polycarbonate RC body?
What does Prographix mean on a Traxxas body?
How much does a Stampede body weigh and does it matter?
Will a painted body last as long as a clear one?
Can I use a Stampede body on a Redcat or other 1/10 truck?
Is a Raptor body harder to fit than a stock Stampede shell?
Should I buy a spare body for my Stampede?
The Bottom Line
The shell that makes the most sense for most Stampede owners is the Traxxas TRA3648 Rock n’ Roll, because it arrives painted, trimmed, and decalled — you mount it and drive, with no paint session and no hole drilling. If you would rather choose your own colour, the Traxxas 3617 Clear Body is the value route, pre-cut and supplied with masks and a decal sheet. And if you want your Stampede to stop looking like every


