8 Best Packout Wall Mount | Skip The Plastic Mounts That Flex

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

Here is the short answer: if you want your Packout boxes off the floor and locked solid, buy a metal plate, not a plastic one. The wall mount is a small accessory with a big job — it carries the full weight of a loaded toolbox, so the material and the plate size decide whether your stack stays put or sags. This guide breaks down eight mounts that fit the Milwaukee PACKOUT system and tells you which size suits a garage wall, a truck bed, or a mobile work cart.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

You will see the difference between a half plate and a full-width plate, why weight ratings matter, and where a plastic mount still makes sense. Every pick below is judged on the same question: does it hold your boxes tight and stay cheap enough to buy several, which is the whole point of the packout wall mount.

Top Picks

Milwaukee PACKOUT 4932471638 Mounting Plate, Red
Best OverallMilwaukee PACKOUT 4932471638 Mounting Plate, Red4.5+★200+ ratingsThe factory Milwaukee plate that locks a PACKOUT box to a garage wall. This is the mount to buy if you want the plate the PACKOUT system was designed around.Check price on Amazon
6-Pack Modular Mounting Plates Compatible with Milwaukee PACKOUT, Wall Mount Plates Fit for PACKOUT Toolboxes, Organizers & Accessories
Best Multi-Pack6-Pack Modular Mounting Plates4.5+★20+ ratingsSix 0.55-inch-high plates in one set, made to park small organizers along a wall. Count is the whole story here.Check price on Amazon
VELCKING for Milwaukee Packout Mounting Plate, Metal Storage Base, Wall and Floor Compatible Toolbox Mount
Most Surface AreaVELCKING for Milwaukee Packout Mounting Plate4.0+★50+ ratingsA 22-inch metal plate wide enough to carry more than one box at once. Width is what sets this plate apart.Check price on Amazon

How To Choose The Best Packout Wall Mount

Most people buy the wrong mount because they pick by price alone, then discover the plate is too small for the box they wanted to hang. Decide where the mount will live and what will sit on it before you spend anything. That single step saves you from drilling holes twice.

Match the plate size to the box, not to the price

A half plate covers a smaller share of a toolbox base, so it suits compact organizers and small cases. A full-width plate spreads a bigger box’s weight across more surface, which keeps a heavy stack from tilting. If you plan to hang a large rolling box, go full-width first and check the dimensions before you drill.

Metal or plastic — pick by load, not by looks

Metal plates hold their shape under load, and the reviews on the steel picks keep coming back to sturdiness and fit. Plastic plates are lighter and cheaper, and they hold up fine on a light box or a wall of small organizers. Put real weight on a thin plastic plate over time and it can flex, so match the material to what the plate will carry.

Wall, floor, or truck bed

Some mounts are wall-only, while others list wall and floor mounting or truck bed and MOLLE panel compatibility. If the plate is going in a truck or trailer, check that the listing names those surfaces, because a dedicated wall bracket often will not sit flat on a floor. Pre-drilled holes make the job easier either way, but the mounting type is the part that must match your plan.

Side-by-Side Comparison

Model Best For Material Mounting Type Plate Size Amazon
Milwaukee PACKOUT 4932471638 Mounting Plate★ Best Overall Garage walls and stationary stacks Impact-resistant polymer Wall 6.82″L x 8.99″H Amazon
6-Pack Modular Mounting Plates (HARBALT)Best Multi-Pack Organizing small boxes in tight spaces High-strength PA plastic Wall 6 Count Amazon
VELCKING Metal Storage BaseMost Surface Area Big wall or floor plate on a budget Metal Wall, Floor 22″W Amazon
BPOPO Aluminum Mounting Plate (Half) Truck beds and MOLLE panels Aluminum Wall, Floor, Truck Bed 15.16″L x 8″W Amazon
NyVoozy Metal Base (1 Full Width) Heavy fixed stacks and truck use Carbon steel Wall/Floor 22″D x 14″W Amazon
BYERN AUTO Full Plate Mobile setups and custom builds Alloy steel Shelf/Wall 21.58″ x 13.19″ Amazon
noblequest Mounting Plate (2 Full Width) Covering two boxes at once Alloy steel Wall 2 Pack Amazon
Milwaukee Plate WALL Compact 48-22-8486 A slim, tidy wall shelf Metal, powder coated Wall 1.19″D x 10.25″W x 20″H Amazon

Detailed Reviews

★ Best Overall

1. Milwaukee PACKOUT 4932471638 Mounting Plate, Red

Our pick — 4.5+★ from 200+ verified ratings; the strongest balance of quality and price.

Impact-Resistant PolymerFits All PACKOUT

The factory Milwaukee plate that locks a PACKOUT box to a garage wall.

This is the mount to buy if you want the plate the PACKOUT system was designed around. It is made of impact-resistant polymer — a tough plastic that shrugs off knocks — and it connects to every Milwaukee PACKOUT modular storage component. The published capacity puts it at 45 kg on the floor and 22 kg on the wall, so a wall-mounted stack of loaded boxes has a stated limit to work within.

Where it beats the generic metal plates is in the physical footprint. It measures just 6.82″ long and 8.99″ high, so it tucks into a narrow wall strip above a bench or beside a door without eating open space. Against the 6-Pack Modular plates, which stand only 0.55″ high, this one offers a far taller mounting face for a single box. That extra height is what stops a mid-size case from feeling perched.

The catch with the compact size is coverage: it holds one box footprint at a time, so a long row of tools means buying several plates. The polymer body also means you should treat the 22 kg wall figure as the ceiling for a loaded stack, not a target. Owners drawn to this plate do so for the tidy, factory-matching look and the honest load numbers. If you want the factory-fit plate for a single box on a garage wall, this is the one.

What it nails

  • Impact-resistant polymer body that handles daily knocks in a shop
  • Stated 22 kg wall and 45 kg floor capacity gives you a clear limit
  • 6.82″L x 8.99″H face fits narrow wall strips without crowding the bench
  • Connects to all Milwaukee PACKOUT modular storage components

Where it falls short

  • One plate covers one box footprint, so a full wall means several units
  • Wall capacity caps at 22 kg, so an overloaded stack can push the limit
  • Polymer body rather than the reinforced metal some buyers prefer

Go for it if: you want the factory-fit plate for a single loaded box on a garage or shop wall.

Think twice if: you need a full-width plate for a heavy rolling case or plan to mount several boxes in a row.

Best Multi-Pack

2. 6-Pack Modular Mounting Plates

Six Plates IncludedEasy Screw Install

Six 0.55-inch-high plates in one set, made to park small organizers along a wall.

Count is the whole story here. You get six mounting plates in one set, versus the single plate you get with the Milwaukee factory mount. Each one stands only 0.55″ high, so six of them stack into a shallow line along a wall without pushing your bench out into the room. That makes the set a natural fit for organizers, small cases, and the bits-and-pieces accessories that pile up on a shelf.

The plates are molded from high-strength PA plastic — a rigid nylon-type material chosen for load and impact resistance — and the listing says the six can be arranged freely to suit the space. You screw each one down where you want it, then slide your PACKOUT interface into the slot. For a workshop wall or a warehouse aisle, that flexibility covers gaps a single large plate cannot.

One detail you need before buying: these plates do not support the locking mechanisms of PACKOUT accessories and cases. So they hold a box in place by interface fit, not by the click-lock some owners rely on for transport. The listing also advises against floor installation. Use these on walls and in trucks or trailers, and treat the lack of a lock as the trade-off for the low multi-pack cost.

Why six wins: spreading six plates across a wall lets you park small organizers exactly where you reach for them, and a shallow 0.55″ profile keeps the wall feeling flat.

The missing click: no support for the PACKOUT locking mechanism means a jostled box can slide rather than lock, so these suit fixed walls more than a bouncing trailer.

Pick this one for: a wall of small organizers where quantity matters more than one big plate.

Leave it for: anything that needs the PACKOUT lock to hold a case down during travel.

Most Surface Area

3. VELCKING for Milwaukee Packout Mounting Plate

Metal BaseWall or Floor

A 22-inch metal plate wide enough to carry more than one box at once.

Width is what sets this plate apart. It measures 22 inches across, and that dwarfs the 0.54-inch width of the Milwaukee factory plate — a 40.7x gap that tells you this is a broad surface meant to carry more than one box. Build quality is the thing buyers call out most, with fit and compatibility close behind, so the base feels solid the moment you set it down.

It is a metal base with pre-drilled holes, and it mounts to a wall or a floor. Better still, it carries a locking mechanism, so the boxes you hang on it stay held in place rather than sliding loose. The listed weight comes to 2.43 kg, which is heavy enough to feel planted on a bench or a workshop floor. For a floor-standing tool tower or a wide garage wall, the size is the argument.

Sturdiness does draw a mixed response, so this is not the plate to buy if you plan to overload it with the heaviest boxes you own. A few buyers worry about how rigid it stays under a big load. Set it up with reasonable weight and the wide metal face earns its keep. What you are really buying is spread-out support across a big footprint.

Best matched to: a wide wall or floor spot where you want one big plate, and it lists both mounting types.

Worth noting: sturdiness reads mixed among buyers, so keep the load sensible rather than maxed out.

Best for Trucks

4. Packout Mounting Plate Half Plate

Aluminum BuildMolle Panel Ready

Built from aluminum to ride on a truck bed or a MOLLE panel without rusting.

Where most plates here stop at the garage wall, this one is listed for wall and floor mounting plus truck bed floors and MOLLE panels. That range is the reason to pick it: a half plate that rides in a vehicle and holds a toolbox steady on a rough road. The body is thickened aluminum, electroplated to resist wear and rust, so road grime and wet weather are not an immediate worry.

The compact half-plate size keeps it easy to fit into tight vehicle real estate. It measures 15.16″ long by 8″ wide by 0.6″ high and weighs 0.46 kg, so several can go into a truck box or onto a panel without weighing the rig down. Against the NyVoozy full-width plate at 2.43 kg, this one lands far lighter on a mobile setup. It also carries the highest buyer rating of the metal plates here.

The half-plate shape is the thing to think about. It covers half a full footprint, so it suits a single compact box or a light organizer rather than a fully loaded large case. If your build leans on a big heavy box in the bed of a truck, spend up for a full-width plate instead. For a lighter load in a vehicle or a custom panel, the aluminum body does the job while staying easy on the hardware.

Light and rust-shy: aluminum keeps the 0.46 kg weight low and the electroplated finish holds up against wear, which suits a truck bed that sees weather.

Half coverage: the plate covers half a footprint, so pair it with compact boxes and lean on a full-width plate for a heavy case.

Reach for this if: your mount lives in a truck bed, on a MOLLE panel, or on a shop floor as a half plate.

Look elsewhere if: you are hanging a large, heavy box that wants a full-width metal plate beneath it.

Heaviest Build

5. NyVoozy Packout Mounting Plate

Carbon SteelScrews Included

A 2.43 kg carbon steel plate that keeps a loaded toolbox flat and planted.

Functionality is what buyers come back to again and again, and the build quality and fit back it up. This is a carbon steel plate with a baked enamel finish that protects against wear and rust, made to sit on a garage wall, a hand truck, or a floor. The screw-in bracket hardware arrives in the box, so the install does not stall on a parts run.

The full-width face is generous at 22″ deep by 14″ wide with a 0.7″ height, which gives a large box real support. At 2.43 kg, it is the heavy one in this group — against the 0.46 kg BPOPO aluminum half plate, it carries a solid, planted feel when you set a loaded case on it. For a fixed stack that never moves, that mass is an advantage, because the plate stays flat under a heavy box.

Travel is where it shines too, with the build holding up through moving and hauling. The secure fit into the interface does draw a mixed verdict, so check the seating once you hang a box and make sure it is fully seated before you load it up. Treat the locking fit carefully and the steel plate rewards you with a stable wall or floor mount for the long haul.

Strength where it counts

  • Carbon steel body with baked enamel finish that resists wear and rust
  • Full-width 22″D x 14″W face supports a large box footprint
  • Screws and mounting hardware included in the box
  • Holds up through travel and hauling, per buyer experience

What to watch

  • At 2.43 kg it is the heaviest plate here, so a truck setup gains weight
  • Secure fit reads mixed, so verify the box is fully seated before loading

Choose it for: a fixed wall or floor spot where a large box needs full-width steel support.

Skip the weight if: you are building a light, portable truck setup and would rather save the kilos.

Best for Custom Builds

6. BYERN AUTO Mounting Full Plate

Alloy SteelHardware Included

A 21.58-inch alloy-steel plate rated to hold up to 100 lbs.

Length is where this plate makes its case. It runs 21.58 inches long against the Milwaukee factory plate’s 6.82 inches, so a single unit spans the base of a full-size box rather than a compact one. The body is rugged alloy steel with a rust-resistant powder coating, and the listed capacity sits at up to 100 lbs. That is enough headroom that a heavily loaded toolbox barely tests it.

It is listed as compatible with all PACKOUT versions, including full-size boxes, and it mounts to truck beds, MOLLE panels, truck walls, cabs, vehicle floors and walls, or custom projects. The locking mechanism is meant to prevent shifting and keep the connection wobble-free during transport. All hardware is included and the plate comes pre-drilled, so the install is a short job.

Bear in mind this is the lowest-rated plate in the group, so check fit and finish on arrival. A full-width plate at 4.4 pounds also means added weight in a vehicle. If you want a long steel plate for a custom build and you value the 100-lb rating over perfect cosmetics, it delivers. Just plan to check the seating and the finish when it arrives.

Suits you when: you are building a custom mount in a cab, on a panel, or across a long toolbox base.

Hold off if: you want the tightest, highest-rated fit and are not willing to check the unit on arrival.

Two-Plate Value

7. Mounting Plate 2 Full Width

Two Full-Width PlatesHolds 100 Lbs

Two full-width steel plates, so you can cover two boxes or keep a spare.

Two plates in one set is the draw here. Each one is made of thick alloy steel with a powder-coated finish that resists wear and rust, and the listing rates a wall-hung plate at 100 pounds of support. The set ships with 6 nuts and 6 bolts, so both plates can be installed without a trip to the hardware store.

Compatibility stretches across the entire Milwaukee PACKOUT series, and the plates fix to garage walls, tool carts, or the ground. They also list truck floors and MOLLE panels as valid surfaces. Quality is what buyers praise most, with compatibility right behind it, so the steel and the fit at the interface both read solid. Two plates at once means you can cover a pair of boxes or stage one for a later build.

The fit does draw mixed feedback, so look closely at how your particular box seats into the interface before you load it up. Some boxes sit tight, and others need a nudge. The pair still covers twice the footprint of a single full-width plate for a build that grows. For a two-box garage wall or a pair of tool carts, the two-pack makes practical sense.

Two-up value: a pair of 100-pound-rated steel plates plus 6 nuts and 6 bolts means two boxes mounted and no hardware run.

Fit varies: seating feedback is mixed, so test each box in its plate before trusting it with a full load.

Made for: a two-box wall or twin tool carts where a matched pair of full-width plates does the job.

Not ideal if: you need a guaranteed snug seat on a box you have not test-fitted first.

Slim Wall Shelf

8. Milwaukee Plate WALL Compact PACKOUT 48-22-8486

Powder-Coated MetalOne Shelf

A compact factory shelf that keeps a handful of tools within reach on the wall.

This one is a different shape to the flat plates — it is a compact wall shelf with one shelf for tools and gear, made from sturdy metal with a powder-coated finish. At 20 inches high and just 1.19 inches deep, it hugs the wall and frees up bench and floor space. If your goal is to get a few items off the ground without a big plate taking up wall room, the compact profile is the fit.

It arrives with the hardware needed for a quick wall mount, and the metal body should take the daily wear of a garage or shop. Where the flat steel plates here stretch 22 inches wide, this one trades that width for a narrow, tidy shelf. That means it holds a light load of accessible tools and accessories rather than a stacked row of big boxes.

The shelf format is the honest limitation. It is not a full mounting plate for a large rolling box, and the one-shelf design means a single surface rather than a stack. Owners who want a factory-matched wall piece for a small toolkit or a work-in-progress project will like the clean look. If you are mounting a full stack, pair it with a plate. This is the tidy-up piece, not the heavy lifter.

A smart add-on for: a garage wall that needs a compact, factory-matched shelf for a few accessible tools.

Not the pick for: mounting a large rolling box or building a full stack wall — that wants a dedicated full-width plate.

Know the Specs

Weight Capacity and What It Means on a Wall

Milwaukee lists this plate’s capacity as 45 kg on the floor and 22 kg on the wall, so the wall figure is the one to respect when a stack hangs on a vertical surface. Other steel plates here list ratings up to 100 lbs. Match the rating to the total weight of the loaded box, not the empty one, and pick the plate with headroom over what you plan to hang.

Plate Size: Half, Full Width, and Multi-Pack

A half plate covers part of a box footprint and suits compact organizers. A full-width plate spreads the load under a large box, and the plates here list widths ranging from about 6.82 inches up to 22 inches. Multi-packs of small plates cover tight spaces where one big plate will not fit. Decide the box footprint first, then choose the plate size that sits under it.

Material and Finish

Polymer plates are lighter and connect directly to the PACKOUT system, while metal plates — aluminum, carbon steel, and alloy steel — carry heavier loads and resist sagging over time. Finishes range from baked enamel to powder coating and electroplating, all aimed at holding off wear and rust. For a truck bed or an outdoor wall, the plated metal finishes are the ones that matter.

Mounting Type and Locking

Some plates are wall-only, while others list wall and floor, and a few name truck bed floors and MOLLE panels. Check that your surface is named before you buy. Locking mechanism is a separate spec: some plates carry a lock to hold boxes, while the 6-Pack plastic plates explicitly do not support the PACKOUT locking mechanisms. On a moving vehicle, that difference matters.

Common Questions

Will a Milwaukee factory mounting plate fit every PACKOUT box?
The Milwaukee PACKOUT 4932471638 plate connects to all Milwaukee PACKOUT modular storage, so it is listed for the whole system. The plate itself measures 6.82″ long and 8.99″ high, which suits a single box footprint. If you are mounting a large rolling box, check the base size and consider a full-width plate instead.
Can I mount a Packout plate on a truck bed or MOLLE panel?
Some can, some cannot. The BPOPO aluminum half plate and the BYERN AUTO plate both list truck bed and MOLLE panel compatibility, and the NyVoozy plate also lists truck use. The Milwaukee factory plate is listed as a wall mount, and the 6-Pack plastic plates advise against floor installation. Check that your surface is named in the listing before you buy.
Is a metal plate stronger than the plastic Milwaukee plate?
The metal plates here are chosen for load and rigidity — the NyVoozy carbon steel and BYERN alloy steel plates both list ratings up to 100 lbs, while the Milwaukee polymer plate lists 22 kg on the wall and 45 kg on the floor. Metal resists sagging under a heavy box, while plastic stays lighter and matches the factory PACKOUT system directly. Pick by the load you plan to hang.
Do these mounts support the PACKOUT locking mechanism?
Not all of them. The 6-Pack Modular plates explicitly do not support the locking mechanisms of PACKOUT accessories and cases, and they hold boxes by interface fit only. The VELCKING plate lists a locking mechanism, and the BYERN AUTO plate lists one that prevents shifting during transport. If a locked-in box matters for a vehicle, confirm the lock is named in the listing.
How much weight can a wall-mounted Packout plate hold?
It depends on the plate. The Milwaukee factory plate lists 45 kg on the floor and 22 kg on the wall. The noblequest two-pack and the BYERN AUTO plate both list support up to 100 lbs when wall-hung. Always size the plate to the total weight of the loaded box and keep a margin under the stated limit.
What is the difference between a half plate and a full-width plate?
A half plate covers part of a box footprint. The BPOPO aluminum plate is a half plate at 15.16″ long by 8″ wide. A full-width plate spans more of the base — the BYERN AUTO plate runs 21.58″ long, and the NyVoozy plate is 22″ deep by 14″ wide. Half plates suit compact boxes and tight spots, while full-width plates suit large, heavier boxes.
Can I install a Packout mount on a garage wall myself?
Yes, most of these are pre-drilled for screwing down. The VELCKING plate has pre-drilled holes, the BYERN AUTO plate ships pre-drilled with all hardware included, and the noblequest set includes 6 nuts and 6 bolts. The Milwaukee compact shelf also includes its mounting hardware. You still need to locate the right spot and use fasteners suited to your wall.
How many boxes will a 6-pack of mounting plates hold?
The 6-Pack Modular set includes six separate plates, so it can hold up to six placements if each box gets its own plate. Each one stands 0.55″ high, so the set stays shallow along a wall. Because the plates do not support the PACKOUT locking mechanism, keep them for fixed wall storage rather than boxes that ride in a moving vehicle.
Will a full-width plate take up too much wall space?
A full-width plate is broader than a half plate, but most stay flat against the wall. The NyVoozy plate is 0.7″ thick, the BPOPO half plate is 0.6″ thick, and the BYERN AUTO plate is 0.78″ thick, so none of them push far out from the surface. The space question is width and height, so measure the wall strip before you choose a full-width unit.
Does the Milwaukee compact wall plate hold a full toolbox?
The Milwaukee Plate WALL Compact 48-22-8486 is a compact shelf with one shelf, at 1.19″ deep and 20″ high. It is built for keeping tools and accessories accessible on a wall rather than stacking a large rolling box. For a full stack, pair it with a dedicated mounting plate that matches your box footprint.

The Bottom Line

For most garages, the packout wall mount winner is the Milwaukee PACKOUT 4932471638 Mounting Plate because it matches the factory system, connects to all PACKOUT storage, and states a clear 22 kg wall limit you can plan around. If you want metal and full-width support for a heavy box, grab the NyVoozy plate. And for a truck bed or a custom panel, the BPOPO aluminum half plate is the one to reach for. Pick the plate that fits your box footprint and the surface you will drill into, and your stack will stay put.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top