Sony requires every internal M.2 SSD in a PS5 to have a working cooling structure, either a built-in heatsink or one you install yourself.
A bare M.2 drive dropped into the expansion slot is the mistake Sony warns about directly. The PlayStation maker’s own install guide states that you should not use an M.2 SSD without an effective heat-dissipation mechanism, such as a heatsink and heat-transfer sheet. That single sentence settles the question, but the surrounding details matter just as much, because the heatsink has to clear a tight height limit before the console’s cover will close.
What Sony Requires For A PS5 SSD
The drive must be a PCIe Gen4 x4 NVMe M.2 with Key M, sized between 250 GB and 8 TB, and Sony recommends a sequential read speed of 5,500 MB/s or faster. Those are the specs most people check. The cooling and size rules are where installations go wrong.
Dimensions get measured as a package, with the heatsink attached. Sony caps the total at 25 mm wide, up to 11.25 mm thick, and 30, 42, 60, 80, or 110 mm long. No more than 8.0 mm can sit above the circuit board and 2.45 mm below it. Both single-sided and double-sided drives fit, though single-sided cooling structures are generally easier to squeeze in.
M.2 SATA drives are not supported at all, no matter what heatsink you attach. Neither is any drive that falls outside the capacity, speed, interface, or size limits. Sony adds one honest caveat: an SSD that meets every spec is not guaranteed to work, and the company accepts no responsibility for third-party product selection or performance.
| Requirement | Specification | Watch Out For |
|---|---|---|
| Interface | PCIe Gen4 x4 NVMe, M.2, Key M | M.2 SATA is not supported |
| Capacity | 250 GB to 8 TB | Anything outside the range |
| Read speed | 5,500 MB/s or faster (Sony’s recommendation) | Faster drives don’t guarantee identical performance |
| Total thickness | 11.25 mm max, heatsink included | A cover that won’t close |
| Above board | 8.0 mm max | Tall aftermarket heatsinks |
| Below board | 2.45 mm max | Thick double-sided builds |
| Cooling structure | Heatsink or heat-transfer sheet, required | Bare drives and stacked heatsinks |
Common Heatsink Mistakes To Avoid
The most frequent error is adding a second heatsink to a drive that already has one built in. Sony says extra heatsinks may actually reduce the effectiveness of the integrated cooler, so a drive like the officially licensed SANDISK Optimus GX PRO 850P, which ships with its own heatsink, needs nothing added.
The second mistake is trusting the advertised form factor instead of measuring the assembled drive. A 2280 SSD with a chunky heatsink can still blow past 11.25 mm of stack height, and then the expansion-slot cover simply refuses to seat.
A third mistake is forcing the drive into the connector. Sony warns that incorrect or incomplete insertion can damage the terminal and the console itself. The drive should slide in diagonally and seat with light pressure, never a shove. If you’re still deciding which cooler to buy, the tested options in this PS5 SSD heatsink buying guide are measured against these exact limits.
How To Install The SSD Correctly
Sony says to update the PS5 system software before you open anything. After that, the procedure differs by model group.
On CFI-2000 and CFI-7000 consoles, follow this order:
- Remove the triangle cover and the expansion-slot cover.
- Remove the screw and spacer, then seat the spacer in the groove that matches your SSD’s length.
- Align the notch on the SSD with the expansion connector and insert the drive diagonally until it is fully seated.
- Lower the drive and fasten it with the screw.
- Reinstall the expansion-slot cover and the triangle cover.
- Reconnect the base, the AC cable, and any other cables, then power on.
CFI-1000 consoles need the power fully off first. Unplug every cable, let the console cool, and set it on a protected flat surface before removing the base and cover. The circuit board has to rest flush on the spacer, and the cooling structure must not block the screw. Then install the drive, secure it, replace the covers, and reconnect power.
Either way, the console prompts you to format the new drive on first boot. Once that finishes, you can choose where games install under Settings > Storage > Installation Location.
Which Consoles And Drives This Covers
The heatsink rule applies to the internal M.2 expansion slot across the CFI-1000, CFI-2000, and CFI-7000 model groups, and Sony’s accessories pages list compatible licensed drives for both PS5 and PS5 Pro. No PlayStation Plus plan or subscription tier changes any of these hardware requirements.
Officially licensed options with integrated heatsinks carry real sticker prices on Sony’s US Direct store, and they move around. Western Digital’s SN850P is also licensed with an all-in-one heatsink. Check current stock before you budget, since availability shifts week to week.
The final check before buying: confirm the drive is Gen4 NVMe, sits inside the capacity range, and that the combined drive-plus-heatsink thickness stays under 11.25 mm. Do that, and the cover closes, the console formats, and your games have room to breathe.
Common Questions
Can I Use A Bare M.2 SSD Without Any Heatsink?
No. Sony’s install documentation says not to use an M.2 SSD in a PS5 without an effective heat-dissipation mechanism. You need either a drive with a built-in heatsink or a separate heatsink and heat-transfer sheet fitted before installation. Skipping this step puts the drive outside Sony’s stated requirements.
Will A Heatsink That’s Too Tall Still Fit?
It depends on the total stack height, not just the heatsink. Sony caps the assembled drive at 11.25 mm thick, with no more than 8.0 mm above the circuit board. A heatsink that pushes past those numbers can stop the expansion-slot cover from closing, so measure the combined package before installing.
Does A Faster SSD Make Games Load Faster Than The Internal Drive?
Not reliably. Sony states that games may not perform exactly the same on an expansion drive even when it exceeds the 5,500 MB/s recommendation. Meeting the specs gets your games running from the new drive; it does not guarantee identical behavior to the console’s built-in storage.
Sources
- Sony Interactive Entertainment. “How to add an M.2 SSD to a PS5 console” Source for the heatsink requirement, supported specs, dimensional limits, and installation steps.