Milwaukee PACKOUT wall storage runs on dedicated Wall Plates bolted to studs that lock every PACKOUT box, shelf, and organizer through the system’s modular interface.
For the full breakdown, see our best Packout Wall Mount guide.
One plate mounted on the wrong surface, or rated for the wrong load, drops a loaded toolbox stack on your shop floor. The mounting system itself is simple: a plate fastens to structural lumber or concrete, then PACKOUT components slide onto its tracks and lock. What decides whether the install holds is the plate you pick, the fasteners Milwaukee specifies, and the weight rating that applies to where you mounted it.
Four plate models show up in Milwaukee’s current US catalog. Two are dedicated Wall Plates, one is an older large plate, and one is a separate Mounting Plate built for wall, floor, and vehicle bases. They do not share load limits, and mixing them up is the most common mistake in this system.
Which Milwaukee PACKOUT Wall Plates Exist Today?
Milwaukee currently lists the Large Wall Plate 48-22-8497 and the Compact Wall Plate 48-22-8496 as its dedicated wall-mounting plates, alongside the older 48-22-8487 and the separate Mounting Plate 48-22-8485. All of them accept PACKOUT components through the same locking interface, so fit is never the question — capacity is.
- 48-22-8497 Large Wall Plate: 30.75 in wide, 4.5 lb, 150 lb maximum on a shop wall and 75 lb in a vehicle.
- 48-22-8496 Compact Wall Plate: 10.25 in wide, 1.5 lb, 50 lb maximum on a shop wall and 25 lb in a vehicle.
Every plate above carries Milwaukee’s limited lifetime warranty and metal-reinforced mounting tracks. The current Wall Plate designs also include quick-alignment tabs, which let you line up several plates in clean rows or columns instead of measuring each one against the last.
| Plate Model | Width and Weight | Load Limit |
|---|---|---|
| 48-22-8497 Large Wall Plate | 30.75 in, 4.5 lb | 150 lb shop wall, 75 lb vehicle |
| 48-22-8496 Compact Wall Plate | 10.25 in, 1.5 lb | 50 lb shop wall, 25 lb vehicle |
| 48-22-8487 Large Wall Plate | 30.75 in, 3.5 lb | 150 lb shop wall, 75 lb vehicle |
| 48-22-8485 Mounting Plate | 23.4 in, 3.47 lb | 50 lb wall, 100 lb vehicle floor |
Choosing Between The Plates: What Decides The Outcome
Pick the 48-22-8497 when you want the widest coverage and the full 150-lb shop-wall capacity. Reach for the 48-22-8496 when a narrow 10.25-in plate fits the wall space you have. The 48-22-8487 only makes sense when a seller or an existing project specifically calls for that model number.
The 48-22-8485 is a different animal. Its 50-lb wall rating is a third of the 48-22-8497’s, but it doubles as a floor-mounted base with 100 lb capacity and includes tie-down points. If your plan involves a truck bed or a shop floor, that plate is the one that does the job.
Comparing plate-and-box combinations against your actual tool load is where most buyers stall — a tested breakdown of wall mount setups can shortcut that decision.
Milwaukee’s catalog page for PACKOUT mounting solutions lists the full current lineup if you want to confirm model numbers before ordering.
How Do You Install A PACKOUT Plate Correctly?
Milwaukee’s instructions require a flat, even surface, at least four corner holes fastened with the specified hardware, and no substitutions on fasteners. An uneven wall can warp the plate and interfere with how PACKOUT components seat on the tracks, so check the surface with a straightedge before you drill.
- Position the plate against the wall according to its orientation, then mark the four corner holes.
- For wood framing, use dimensional lumber at least 2×4 or 3/4-in plywood. Drive four 1/4-in-diameter × 1-1/4-in lag screws. Skip self-tapping screws and drywall screws entirely — Milwaukee’s guide rules them out.
- For concrete, use four suitable concrete anchors rated for the load.
- If 16-in-on-center studs aren’t available, Milwaukee directs you to the four corner holes that give maximum support.
- Attach components once the plate is solid. PACKOUT boxes lock onto the tracks, and the tabs line up additional plates.
When it’s right, the plate sits flush with no rocking, and a loaded PACKOUT box locks down without wobble. If the box fights the track, back the fasteners off and check for warping.
What Mistakes Break A PACKOUT Wall Install?
The failures cluster around three things: wrong plate rating, wrong fasteners, and forgetting what the boxes weigh. Count the PACKOUT containers and everything inside them against the plate’s limit — a 150-lb plate fills up faster than most people expect.
- Treating the 50-lb wall rating of the 48-22-8485 as if it matched the 150-lb shop-wall rating of the 48-22-8497.
- Applying vehicle ratings to a shop wall, or pushing past the lower figure when conditions are uncertain.
- Mounting to unsupported drywall with no structural lumber behind it.
- Installing on an uneven surface, which warps the plate and jams the lock.
Prices are the one gap worth naming.
Common Questions
Can I use PACKOUT Wall Plates on a vehicle?
Yes, but at the reduced vehicle rating. The 48-22-8497 and 48-22-8487 drop to 75 lb in a vehicle, and the 48-22-8496 drops to 25 lb. If vehicle mounting is the main plan rather than an occasional move, the 48-22-8485 Mounting Plate with its 100-lb floor capacity and tie-down points is the better fit.
Do all PACKOUT boxes fit every plate?
Every plate in the lineup uses the same modular locking interface, so PACKOUT organizers, toolboxes, and shelves connect to any of them. What changes between models is width, mounting hardware spacing, and load capacity — not compatibility with the components themselves.
How heavy can a PACKOUT wall setup actually get?
The full 150 lb applies only to the large plates on a shop wall. That figure covers the containers plus their contents, so a stack of loaded toolboxes can reach it quickly. On the compact plate, plan around 50 lb, and count every box in the stack against that number.
Sources
- Milwaukee Tool. “PACKOUT Mounting Solutions” Lists current Wall Plate and Mounting Plate models with capacities.
- Milwaukee Tool. “48-22-8485 PACKOUT Mounting Plate” Source for wall, floor, and vehicle load ratings and stack-height limits.
- Milwaukee Tool. “Milwaukee Expands PACKOUT System with New Solutions to Customize Your Shop” April 4, 2022 press release carrying historical introductory pricing.