A cue stick is the tapered implement used to strike the cue ball in pool and billiards, built from a tip, ferrule, shaft, joint, and a heavier butt.
A conventional pool cue runs about 58 inches long and 17–21 ounces, and every part of that length does a job — from the leather tip that contacts the ball to the rubber bumper that cushions the base. Knowing what each section does makes it far easier to judge whether a cue, or a replacement part, is worth buying.
Below is the full anatomy from tip to bumper, the competition limits that actually apply, and the compatibility traps that catch buyers most often.
The Parts Of A Pool Cue, Tip To Bumper
A pool cue splits into a slim front half (tip, ferrule, shaft) and a thicker rear half (joint, forearm, wrap, butt sleeve, cap, bumper). The front half delivers the stroke; the rear half supplies the weight and the grip.
- Tip: The replaceable striking surface, usually leather or another fibrous material. Pool tips measure roughly 11–14 mm across, with 12–13 mm the common range. Hardness (soft to hard) changes feel, spin response, and how long the tip lasts.
- Ferrule: The short sleeve directly under the tip. It supports the tip and protects the shaft end from impact and splitting. Plastic, composite, and resin are typical materials.
- Shaft: The long tapered front section that slides through your bridge hand. Hard maple is traditional; graphite, fiberglass, and carbon fiber are also offered.
- Taper: How the shaft’s diameter grows toward the butt. A straight (European) taper widens continuously; a pro taper holds a near-constant diameter for a stretch before widening faster.
- Joint and collars: The connection point on a two-piece cue. Collars reinforce it and create a flush, stable fit. Metal, wood, and phenolic resin are common joint materials.
- Joint pin: The threaded stud that screws the shaft to the butt. Pin sizes and thread patterns differ by maker.
- Forearm: The upper butt section below the joint, usually wood, often carrying decorative inlays under a finish.
- Wrap: The grip area, covered in Irish linen, nylon, leather, or synthetic material. It improves handling and shields the wood from sweat and moisture.
- Butt sleeve: The lower decorative section beneath the wrap. Some cues hide an internal weight-bolt system here.
- Butt cap and bumper: The cap finishes and reinforces the base; the rubber bumper absorbs contact with the floor.
How Big And Heavy Can A Competition Cue Be?
Competition rules are far more permissive than market norms. World Pool-Billiard Association equipment specifications require a cue to be at least 40 inches (1.016 m) long with no maximum length, and no more than 25 oz (708.75 g) in weight.
On tip and ferrule, the same WPA specifications set the tip at no more than 14 mm wide with no minimum, require a leather or other fibrous, pliable material that contacts the ball without scratching or damaging it, and cap a metal ferrule at 1 inch (2.54 cm). The numbers below compare everyday market sizing against those limits.
| Component | Typical Market Spec | Competition Limit |
|---|---|---|
| Overall length | About 58 inches | Minimum 40 inches (1.016 m); no maximum |
| Shaft length | About 29 inches on a 58-inch cue | Not separately capped |
| Playing weight | 17–21 oz; 19 oz common | Maximum 25 oz (708.75 g) |
| Tip width | 11–14 mm; 12–13 mm typical | Maximum 14 mm; no minimum |
| Tip material | Leather or fibrous material | Must be fibrous/pliable and not damage the ball |
| Metal ferrule | Varies by design | Maximum 1 inch (2.54 cm) |
| Joint pin | Maker-specific threads | Not restricted, but not interchangeable |
Which Mistakes And Compatibility Problems Catch Buyers?
The single most expensive assumption is that two-piece shafts and butts swap freely. Joint-pin type, thread, collar dimensions, and joint geometry all have to match, so a shaft from one maker often will not seat on another maker’s butt.
Discipline matters too. Pool, snooker, and carom cues differ in tip diameter and overall proportion, so a cue built for one game will feel wrong in another. If you are shopping for replacements, the tested comparisons in this roundup of parts for cue stick upgrades show which components are worth swapping and which are not.
Tip choice deserves its own caution. Smaller tips can favor precise spin control while larger tips give a broader contact patch, so pick diameter and hardness by playing preference and discipline rather than looks. A hard, damaged, or badly installed tip is also a rules problem: WPA specifications require tip material that will not scratch or damage the addressed ball. The WPA equipment specifications spell out that material requirement along with the length, weight, and ferrule limits.
Decorative inlays and overlays are largely cosmetic. Shaft straightness, joint fit, tip condition, and taper are the functional concerns that change how a cue plays.
Sources
- World Pool-Billiard Association. “WPA Equipment Specifications” Source for cue length, weight, tip, and ferrule competition limits.
- PoolDawg. “Anatomy of a Pool Cue” Reference for cue component terminology and layout.