How to Mount a Camera on an RC Car?

A rigid clamp, screw-on bracket, or FPV mount on the upper chassis holds a camera steady on an RC car; center it low, tighten it against vibration, and test handling before speed.

A camera that slips one click mid-run ruins the whole clip, and the mount is what decides that. Bolting a GoPro HERO13 Black or similar action camera to a hobby-grade RC car comes down to four things: picking the right interface, finding a spot the chassis can carry, killing vibration, and checking the car still drives the way it did before the extra weight went on.

The payoff is footage no handheld shot can match — ground-level speed, suspension working, tires biting. The cost of getting it wrong is a cracked body shell or a camera in a ditch. Here is the order that works.

Which Mount Type Fits Your Camera And Car?

Match the mount to the camera’s attachment interface first, then to the car’s structure. Most action cameras use one of three systems, and the HERO13 Black covers all three: built-in GoPro mounting fingers, a 1/4-20 thread, and GoPro’s magnetic latch.

  • GoPro fingers and thumbscrew — the classic two-prong hinge. Cheap, rigid, and widely cloned. Best all-round choice for a chassis bracket.
  • 1/4-20 screw — standard tripod thread. Use it with a plate bolted to the chassis; the screw gives fine aim adjustment.
  • Adhesive base — fast to fit, weak on dusty, wet, sharply curved, or heavily vibrating bodies. Fine for a first test, not for repeated jumps.
  • FPV bracket or cage mount — model-specific, screws directly to the frame. The most secure option for fast cars and hard landings.

A screw-mounted chassis bracket beats adhesive every time on a car that takes impacts. GoPro’s magnetic latch is handy for quick swaps, but treat it as a convenience, not the only thing holding the camera on at speed — add a tether or a mechanically fastened mount for jumps and crashes.

Where Should The Camera Sit On The Chassis?

Mount to a rigid part of the upper chassis or roll cage, as close to the vehicle’s centerline as you can get, and as low as the shot allows.

Mass added up high raises the center of gravity. A tall stack of brackets makes rollovers more likely and slows the car’s recovery in corners. A low, centered camera keeps handling closer to stock and gives a tighter, faster-feeling view. A higher position widens the frame, so pick the height your shot needs and accept the handling trade.

Skip thin body panels, suspension arms, steering links, rotating parts, motor heat sinks, and the antenna. Those flex, move, or radiate heat and interference. Drill into the chassis only where there is solid material underneath, and back the fastener with a washer or a small plate so the load spreads.

How Do You Stop Vibration And Loose Fasteners?

Tighten the mount firmly, but stop before you strip plastic threads, then lock the joint against vibration.

RC cars generate constant high-frequency shake, and a mount that feels solid in your hand can walk loose in two minutes of running. A locking nut, a thread-locking compound suited to the fastener, or a safety tether around the camera body solves it. Flexible adhesive foam between the bracket and the chassis helps kill the buzz that shows up as jello in the footage.

Aim the lens before you drive. Check the frame for the hood, bumper, body shell, wheels, suspension arms, and steering gear — anything creeping into the corner of the shot will be there for the whole run. If you run external power, route the USB-C cable clear of driveshafts, gears, tires, shocks, and hot motor or exhaust parts, and leave slack for suspension travel.

What Changes On The Car After You Add A Camera?

Expect the car to feel heavier and roll more easily, and plan to test before you drive fast.

Check What To Look For Fix
Steering Slower turn-in, wider arcs Lower the camera or shift it toward center
Suspension travel Arms contacting the mount or cable Raise the bracket, reroute the cable
Rollover clearance Camera hits first on a tip-over Shorten the stack, tuck it inboard
Radio range Shorter range, glitchy throttle Move the camera off the antenna, keep wiring away
Body shell Cracks at mount holes Washer or backing plate under the fastener
Fasteners Loosening after impacts Locking nut, thread locker, tether
Cable routing Chafing, snagging on moving parts Clip it down with slack for travel

Run a stationary check first — steering full lock both ways, suspension compressed by hand — then a slow lap. Inspect the mount and fasteners after the first impacts, and again every few runs. If you would rather compare cameras before you commit, this roundup of RC car camera options tested for durability covers what holds up under this kind of abuse.

Battery life sets the practical limit on run length. For long sessions, GoPro’s Contacto Magnetic Door and Power Cable Kit runs the camera from external USB-C power with a weatherproof connection.

Weather resistance is not a free pass. Mud, abrasive dust, standing water, and pressure washing can wreck a camera and a mount that survived the drive. Keep the battery door, controls, cooling openings, and card slot accessible so you can check them between runs, and drive within reliable control range, away from people, roads, and property you do not have permission to be on.

Common Questions

Can I use an adhesive mount on an RC car?

Yes, for light use on a clean, dry, gently curved surface. Adhesive bases struggle with dust, moisture, sharp curves, and constant vibration, and they tend to let go after a few hard landings. A screw-mounted chassis bracket is more secure for repeated impacts and high-speed driving.

Will a camera slow my RC car down?

It adds mass, so acceleration, cornering, and rollover behavior all shift slightly. A low, centrally placed camera keeps the change small. Test at low speed after installation and adjust spring or shock settings if the car feels noticeably tippier than before.

Does the camera need a case for off-road running?

Dust and mud are the main threats, and a case helps. GoPro states the HERO13 Black fits the HERO12 Black Protective Case and Media Mod, so existing protection carries over. Skip pressure washing the camera regardless of what case you use.

Sources

Scroll to Top