Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
Your snow blower quit mid-driveway, and the real question is which replacement part actually fits your machine. That is what this list answers. Every pick here is a part confirmed to fit Troy-Bilt snow blowers — shear pins, skid shoes, paddles, belts, carburetors and a chute tool — with the exact part numbers spelled out so you can match your own manual before you order.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
The part number on your old component is the whole ballgame here, so check it twice before you buy anything. Below you will find the exact fitment notes and hardware counts for every troy bilt snow blower parts pick.
Top Picks



How To Choose The Best Troy Bilt Snow Blower Parts
Replacement parts live or die on one thing: the part number. Troy-Bilt builds several near-identical machines under the Storm badge, and two carburetors that look the same on a shelf can have completely different choke linkages. Before you buy anything, find the sticker on your machine or pull the old part and read the number stamped or molded into it. Then match that number to the listing — not just the model name.
Match the number, not the model name
A listing that says it fits a Storm 2410 may fit yours, or it may fit only one of the two carburetor variants that machine shipped with. Look for a listing that names the specific part numbers it replaces. A shear pin set that lists 738-04124A and 714-04040, for example, is telling you exactly which machines it will lock into.
Hardware included or not
Skid shoes and paddles wear out with the bolts still in place, so having the mounting hardware in the box saves a second trip to the hardware store. Some sets ship with carriage bolts, hex lock nuts and washers; others are the shoes alone. Read the package contents line carefully if your old hardware is rusted or lost.
Wear parts versus fix-it parts
Shear pins, paddles, skid shoes and belts are wear items — they are supposed to give out under load or after seasons of ground contact. A carburetor is a repair part, swapped when the engine stops starting or running clean. Knowing which category you are shopping in tells you whether to buy a multi-pack or a single unit.
Side-by-Side Comparison
| Model | Best For | Part Type | Key Spec | Piece Count | Amazon |
|---|---|---|---|---|---|
| 30 Pack Cotter Shear Pins★ Best Overall | Stocking up for the season | Shear and cotter pins | 1/4″ diameter x 1.65″ long | 30 | Amazon |
| Universal Roller Skid ShoesBest for Driveways | Protecting the driveway surface | Skid shoes | 2-3/4″ slot, 3″ bolt centers | 2 | Amazon |
| 753-04472 Rubber Paddle SetBest for Single-Stage | Refreshing a 21″ single-stage auger | Rubber paddles | 1 7/8″ W x 11 1/4″ L half-round | 6 | Amazon |
| 731-2643 Chute Clearing Tool | Clearing a clogged chute safely | Chute tool | 16.98 x 4 x 5 inches, 0.18 kg | 2 | Amazon |
| 784-5580 Slide Shoes | Storm 2410 owners wanting full hardware | Skid shoes | 4.75″ L, 2.75″ hole center to center | 2 | Amazon |
| 951-12705 Carburetor | Storm 2410 with metal auto-choke | Carburetor | PC210705 metal choke linkage | 1 | Amazon |
| 951-15236 Carburetor | Storm 2410 with black plastic choke | Carburetor | PC210236 plastic choke linkage | 1 | Amazon |
| 954-04195A Auger Belt | Wide Troy-Bilt Storm coverage | Auger belt | 1/2″ width x 37″ length | 2 | Amazon |
| MTD 954-04050A Auger Belt | Genuine OEM replacement | Auger belt | 0.5″ top width x 35″ length | 1 | Amazon |
Detailed Reviews
1. 30 Pack Metal Cotter Snowblower Shear Pins
Our pick — 4.5+★ from 300+ verified ratings; the strongest balance of quality and price.
Thirty pins in a storage box, so a snapped shear pin never ends your snow day.
Shear pins are meant to break — that is the whole job. When the auger hits a chunk of ice or a buried newspaper, the pin shears so the gearbox does not. If you own a 2-stage or some 3-stage Troy-Bilt, having a box of them beats a trip to the shop in a storm.
These measure 1/4″ diameter by 1.65″ long, with a 0.25-inch groove diameter so they seat in the auger shaft the way the factory part does. The metal is zinc plated, which is a coating that resists rust — note because these pins sit in snow and slush all winter. The set covers replacement numbers 738-04124A, 738-04124 and 714-04040 across Troy-Bilt, MTD, Craftsman, Cub Cadet, Yard Man and Bolens machines.
Compared with the auger belt below, which ships as a 2-pack, this is a bulk wear item — 30 pins plus 30 cotter pins in one box. The install is a push-and-lock job: slide the pin through, drop the cotter pin in to hold it, and check it seated. As owners put it, the value and the part quality are what keep them coming back, though some find the pins break faster than expected and a few struggle with the install. The honest catch is that fitment varies by machine, so confirm your manual lists 738-04124A or 714-04040 before you count on these.
Where It Delivers
- 30 pins plus 30 cotter pins with a storage box — a full season of spares
- Zinc-plated metal resists rust through wet snow
- Listed for Troy-Bilt, MTD, Craftsman, Cub Cadet, Yard Man and Bolens
- Exact 1/4″ x 1.65″ sizing for a clean seat in the auger shaft
What To Watch
- Durability is genuinely mixed — some pins last, some snap fast
- Installation frustrates a share of buyers
- Only fits machines that use those specific part numbers
Right call for: anyone who wants a bulk box of shear pins on the shelf before the first storm.
Check first: your manual must list 738-04124A or 714-04040, since these are machine-specific pins.
2. Universal Roller Skid Snow Thrower Shoes
Rollers under the auger housing that let the machine glide instead of scrape.
Skid shoes are the two runners that sit under the auger housing and ride the pavement. Factory steel shoes gouge and wear; these are nylon, which is a tough plastic that handles cold and holds up better against ground contact. At 0.58 kg for the pair, they carry real substance — noticeably heavier than the 0.18 kg chute tool further down, which makes sense for a part that drags across concrete and asphalt.
What wins people over is how the blower rolls afterward — the nylon rollers lift the housing and let it glide across pavement. The shoes slide along and lift the auger housing slightly, so the steel edge stops grinding the surface. That matters if your driveway is paved and you are tired of fresh scratches each winter.
The fit is the moving part. Slot spacing is 2-3/4″ with 3″ bolt centers, and the maker notes hole distance can vary slightly between batches. If the shoes do not line up on your machine, the nylon construction means you can drill a fresh hole to match your thrower. Some buyers report a perfect fit and others hit alignment trouble on certain machines, so measure your existing shoes before ordering. The recurring note is bolt alignment — check it twice.
Maneuverability payoff: the roller design makes the blower easier to steer across a driveway, and that is the thing people talk about most after fitting them.
Batch variance: hole spacing can shift a touch between batches, so plan on a drill as your backup if the holes do not line up.
Reach for these if: your paved driveway is taking a beating from steel shoes and you want the machine to roll.
Measure before you buy: grab your old shoe’s slot and bolt-center spacing — batch variance makes drilling a real possibility.
3. 753-04472 Rubber Paddle Set
Six rubber paddles that put the bite back into a tired 21-inch single-stage auger.
If your single-stage machine is throwing slush instead of snow, the rubber is likely worn thin. This set restores the sweep. You get four half-round paddles at 1 7/8″ W x 11 1/4″ L x 1/4″ H with four mount holes each, plus two rectangle paddles at 1 7/8″ W x 4″ L x 1/4″ H with two mount holes. That is a complete six-piece refresh.
Fit is what carries this set — the half-round and rectangle paddles match the 21-inch auger geometry. The paddles are listed for 21-inch MTD, Yard Machines and Craftsman single-stage throwers from 2005 and newer, replacing numbers 753-04472, 735-04033, 735-04032, 780-035, 13167 and 953-04472, and Troy-Bilt appears on the fitment list too. The one hard rule: if your machine has a metal-backed auger on a 2004 or older unit, these will not fit.
Installation is straightforward enough that most get it done without trouble, and the auger throws like new once the fresh rubber is on. Durability is the fair caveat — rubber is a wear material, and some sets go longer than others. Treat it as a seasonal part, not a permanent one, and you will be happy with the result. Verify your model against the listing’s MTD number list before ordering, since the 2004 cutoff is unforgiving.
The fit wins: this set is aimed squarely at 21-inch 2-cycle machines and gets the geometry right, which is why it stands out.
Model-year gate: a metal-backed auger on a 2004 or older machine rules these out entirely.
Suits: 21-inch single-stage Troy-Bilt, MTD, Craftsman and Yard Machines owners from 2005 and newer whose rubber has gone smooth.
Not for: older machines with a metal-backed auger — the paddles will not mount.
4. 731-2643 Snow Thrower Chute Clearing Tool
A light chute tool at 0.18 kg, sized to clear slush without reaching into the auger.
Wet, heavy snow is what clogs a chute. This is the tool that clears it. At 0.18 kg it weighs almost nothing and measures 16.98 x 4 x 5 inches, so it stores on or near the machine and does not add drag. Compare that with the 0.58 kg skid shoes above — at 0.18 kg, this tool is meant to be carried, not mounted.
Its job is breaking up slushy clogs in the discharge chute without a hand near the auger. The alloy steel blade and ergonomic grip do the work a gloved hand should not. It replaces OEM numbers 931-2643 and 731-2643 and is listed for MTD, Craftsman and Troy-Bilt machines, with an alloy steel blade and a metal handle with an ergonomic grip.
The catch is fitment and finish. You are buying a tool, not a machined showpiece, and it lands in some machines more cleanly than others. Check that 731-2643 is your number, and treat the chute as the thing that blocks — the tool gets you back up and throwing rather than being a permanent upgrade.
Buy it for: the safety of clearing a clogged chute with a proper tool instead of a gloved hand.
Confirm the number: 731-2643 or 931-2643 needs to match, since this is a machine-specific replacement part.
5. 784-5580 Slide Shoes
Two steel slide shoes plus every bolt, nut and washer you need to bolt them on.
This is the pick for the owner who does not want to hunt down fasteners. The box holds two slide shoes, four carriage bolts, four hex lock nuts and four belleville washers. Belleville washers are slightly dished washers that keep tension on the joint so the bolts stay snug through vibration — a small detail that matters on a machine that shakes all day.
The shoes measure 4.75″ long, 3″ high, with a mounting hole length of 2.1″ and hole centers at 2.75″. They bolt on next to the auger housing, ride the ground and lift the housing so it clears the surface, and they adjust for different clearing depths. Replacement numbers covered run 784-5580, 784-5580-0637, 984-5580, 784-5580-0498, 784-5580-0662, 784-5580-0665, 784-5580-0638, Rotary 8828 and 780-420.
Fit is the standout — these are aimed at the Storm 2410 and a long list of MTD 2-stage machines, and they land where they should. Compared with the universal nylon shoes above, this pair is steel and machine-specific rather than a drill-to-fit roller. The genuine limit is that they only suit machines running those numbers, so the tidy hardware kit is worth nothing if 784-5580 is not your part.
Complete kit: fasteners in the box means no second hardware-store run, and the steel shoes are built to take ground contact.
Fitment lock-in: the shoes are sized to specific housing geometry, so verify the 784-5580 number against your machine first.
Best fit: Storm 2410 and MTD 2-stage owners who want new shoes and hardware in a single box.
Wrong turn if: your machine runs a different skid shoe number — this kit does not adapt.
6. 951-12705 Carburetor
The metal-choke carburetor that brings a stubborn Storm back to a first-pull start.
Owners rave about first-pull starts after this carburetor goes on. It is the part that gets a hard-starting Storm 2410 or 2620 running like new, and starting on the first pull is the reason it earns this spot. If your engine turns over and will not catch, or runs rough, this is the fix you are shopping for.
There is a critical split you have to catch before ordering. The Storm 2410 shipped with two similar carburetors. This listing is exclusively model PC210705, which has a metal auto-choke mechanism on top and no black plastic slot for the choke arm. The model below — the 951-15236 — is the other one. Compare the top linkage on your original carb against the gallery photos before you buy, because choke compatibility is the one recurring complaint here and it is entirely avoidable.
You get a lot in the box: the carburetor, three gaskets, two oil tubes, a fuel filter, a primer bulb, two clamps, a shut-off valve, a spark plug and two shear pins. Fit is listed for the 2410 and 2620 across those part numbers, and the maker backs it with a 90-day warranty. The trade-off is that completeness and choke fit are mixed — the box is generous, but the wrong linkage stops the install cold.
Why It Earns The Callout
- Runs like new and fires on the first pull — the performance is the story
- Full kit: gaskets, fuel filter, primer bulb, spark plug, shut-off valve and more
- 90-day manufacturer warranty
- Listed for Storm 2410 and 2620 part numbers
The Fitment Trap
- Only model PC210705 — the metal auto-choke version
- Will not work on the black-plastic-choke variant
- Covers a narrower model list than the belt options
Pick this one: if your Storm 2410 or 2620 carb has a metal auto-choke linkage on top.
Look at the next pick: if your choke arm sits in a black plastic slot — that is the PC210236.
7. 951-15236 Carburetor
The plastic-choke twin of the carb above — same machine, different linkage, still first-pull.
Same Storm 2410, different carburetor. This listing ships model PC210236, the version with the black plastic choke slot. That single difference is the whole reason both carburetors exist on this list. Order the wrong one and it will not install; order this one and it drops straight in. If your original has that black plastic slot, this is your part.
Installation is the pleasant surprise — the swap runs about 30 minutes, and it comes with everything needed: the carburetor plus three gaskets, two oil tubes, a fuel filter, a primer bulb, two clamps, a shut-off valve, a spark plug and two shear pins. It replaces 951-15236 and 751-15236 and is listed for Troy-Bilt 31AS6BN2723 and 31BS6BN2711, plus Huayi 170SD and 175SC engines and MTD Craftsman SB410 units. That is a wide net for a repair part.
Once in, it starts on the first pull and runs clean — the fix that turns a dead Storm back into a working one. Durability here is about the engine, not the part, and the 90-day warranty covers the early window. The one caution is the model split again: compare your original against the gallery photos, because the two Pro Chaser carburetors look alike on a shelf.
The install is quick: a roughly 30-minute swap with a complete gasket kit puts the machine back in service.
Read the linkage: this is the plastic-choke model — the metal one two spots up is a different part number.
Go here if: your Storm carb has a black plastic choke slot and the old one will not start.
skip it if: your linkage is the metal auto-choke — grab the 951-12705 above instead.
8. 954-04195A Auger Drive Belt
A half-inch, 37-inch auger belt with a fitment list long enough to cover most Storms.
Length and width are what you shop on with a belt. This one is 1/2″ wide and 37″ long, made with aramid cord — a high-strength fibre used inside belts so they hold shape under the auger’s load. You get two in the pack, so a spare goes in the toolbox. That is a real edge over the single-belt MTD option below, where one failure means one more order.
The fitment list is where this belt earns its keep. It replaces 754-04195, 754-04195A, 954-04195, 954-04195A and 490-501-C080, and it is listed across the Troy-Bilt Storm line — 2410, 2420, 2490, 2610, 2620, 2690, 2840, 2890 and 3090 — plus a long run of Craftsman, Cub Cadet, Columbia and Yard Machines models. For a Troy-Bilt owner unsure of the exact sub-model, this belt covers more of them than most.
Honest note on durability, because belts are the part that fails under stress. Some of these fail on a first run or shred after a few months, while others hold up fine — that spread is real. Fit itself is the strong point. Match your thrower’s model code to the listing and keep the second belt ready.
Fitment breadth: covering the whole Storm line from 2410 to 3090 makes this the belt to reach for when the model code is fuzzy.
Buy the pair: durability is uneven, so the second belt in the box is the reason to pick this over the single-belt option.
Choose this belt if: you own a Storm 2410 through 3090 and want a spare on hand for the price of one order.
Accept the gamble: belt life is genuinely uneven, so treat the second belt as planned backup, not a luxury.
9. MTD 954-04050A Snow Thrower Auger Belt
A genuine MTD belt at 0.5″ wide and 35″ long, for owners who want the factory part.
Some owners do not want an aftermarket belt. They want the one the factory built the machine around. This is that — a genuine OEM MTD part, smooth V-belt, 0.5″ top width and 35″ length, weighing in at 3.2 ounces. It fits 2-stage snow throwers from 2005 and after across Troy-Bilt, MTD, Yard-Man, Huskee, Yard Machines, Bolens, Craftsman and Cub Cadet, and it replaces 754-04050, 954-04050 and 754-04050a.
Here is the swap worth knowing: this smooth v-belt replaces the older cogged belt, though it needs a modification to do so. That is the one wrinkle on an otherwise simple part. It is listed for specific Troy-Bilt and Yard-Machines models — 1030, 2100, 2600, 21XPL, 21XPES, 600C, 60024PC — so the fit is narrower than the 37-inch belt two picks up.
Once it is on, the auger drives as the factory intended — that is the whole value of going OEM. Compared with the aramid 37-inch belt, this one is a single unit and shorter, so it suits a specific set of machines rather than the whole Storm family. If yours is on the list, the factory-fit is the cleaner choice.
Factory part: a genuine MTD V-belt removes any question about spec — 0.5″ width and 35″ length, straight from the maker.
Modification required: swapping out a cogged belt takes a tweak, and the model list is specific — check 954-04050A is yours.
For you when: your thrower is on the MTD list and you want the genuine factory belt rather than an aftermarket equal.
Otherwise: if your model is not listed, the 37-inch aramid belt covers more of the Storm line.
Know the Specs
Part numbers and what they mean
Every Troy-Bilt replacement part carries a factory number — 738-04124A for a shear pin, 954-04195A for a belt, 951-12705 for a carburetor. The number identifies the exact geometry, so two parts with the same number are interchangeable and two without are not, even if they look alike. Always read the number off your old part or the machine’s sticker and match it to the listing’s replacement-number line. The model name alone can cover multiple variants.
Shear pins, belts and wear
A shear pin is a deliberate weak link. It sits in the auger shaft to 1/4″ diameter by 1.65″ long and shears under load so the gearbox survives a hit. An auger belt is the drive link from engine to auger, sized by width and length — 1/2″ by 37″ or 0.5″ by 35″ — and it wears out under repeated load. Both live in the same category: parts meant to give out so the expensive metal does not. Keep spares of both.
Common Questions
How do I know which part number fits my Troy-Bilt snow blower?
Why do my shear pins keep breaking?
Will the 784-5580 slide shoes fit my Storm 2410?
What is the difference between the 951-12705 and 951-15236 carburetors?
Can I use a 37-inch belt on any Troy-Bilt snow blower?
Do I need special tools to install these parts?
Are aftermarket parts as good as genuine Troy-Bilt parts?
How long should snow blower shear pins and belts last?
What is the 731-2643 chute tool actually for?
The Bottom Line
For most Troy-Bilt owners, the part worth stocking before the first storm is the 30 Pack Shear Pins — thirty pins and thirty cotter pins at 1/4″ x 1.65″, so a snapped shear pin never stops the driveway. If you own a Storm 2410 or 2620 that will not start, the carburetor decision is the one to get right: the 951-12705 for the metal auto-choke and the 951-15236 for the black plastic choke slot. And for anyone who wants a spare auger belt on hand, the 37-inch 954-04195A 2-pack covers the whole Storm line from 2410 to 3090.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.





