Pick a gauge whose maximum reading sits above your trailer tire’s required cold pressure and its sidewall maximum; most US trailer tires land in a 0–100 or 0–150 psi gauge.
An undersized gauge pegs at the top of its scale and leaves you guessing. A 200-psi racing gauge barely moves across an 80-psi trailer range. Matching the gauge’s range to the pressure you actually run is the whole job.
Find Your Trailer’s Required Cold Pressure First
The correct inflation pressure comes from the trailer’s tire placard, certification label, or owner’s manual—never from the gauge and never from the sidewall maximum alone. Federal tire-labeling rules (49 CFR §571.110) build placard requirements around the manufacturer-recommended cold pressure.
Then check the sidewall for its maximum cold-inflation pressure. Now you hold two figures: the pressure you should run and the ceiling you must never cross. Your gauge’s top-end reading needs to clear both. A placard value below the sidewall max is normal: placard pressure is tied to your trailer’s rated load, while sidewall maximum is the tire’s absolute limit.
Match Gauge Range to Trailer Tire Pressures
Official ST Radial load-and-inflation data lists pressure points from 25 psi up to 80 psi depending on tire size and load range. That’s why an 80- or 100-psi-capable gauge covers most trailer tires, and a 150-psi model adds margin. Hankook’s trailer tire guide, for example, shows Load Range D and E tires topping out at 80 psi.
Four representative sizes from that data:
- ST205/75R14 — 1,170 lb at 25 psi through 2,150 lb at 80 psi (Load Range D max 80 psi).
- ST205/75R15 — 1,220 lb at 25 psi through 2,150 lb at 80 psi (Load Range D max 80 psi).
- ST225/75R15 — 1,430 lb at 25 psi through 2,830 lb at 80 psi (Load Range E max 80 psi).
- ST235/80R16 — 1,720 lb at 25 psi through 3,420 lb at 80 psi (Load Range E max 80 psi).
Read that table as a map of where trailer pressures live, not as a recommendation for your trailer. Your placard still wins.
Headroom is the rule: the gauge’s maximum must exceed the highest pressure you’ll measure. A gauge that maxes out exactly at your placard pressure has nowhere to go when the tire runs slightly high.
Resolution matters just as much. A 0–150 psi dial with coarse marks can blur the difference between 60 and 65 psi—a meaningful gap on a trailer tire. Fine increments or a digital display keep a low-pressure reading legible even when the gauge reaches higher.
Two more fit checks before you buy:
- Dual or tandem wheels: recessed valve stems need a head that reaches them. A dual-head gauge is the standard choice for dual-tire setups.
- Units: confirm the gauge reads in psi, the norm for US trailers. Don’t confuse psi with kPa or bar.
For a tested shortlist of gauges that meet these range and fit requirements, our trailer tire pressure gauge comparison lays out what each model covers.
Check The Tire The Right Way
Measuring cold is not optional—the tire must have sat unused for at least three hours, because driving heats it and temporarily raises pressure, making a hot reading useless for setting cold pressure. NHTSA’s tire safety guidance treats cold measurement as the baseline for a reason.
- Find the recommended pressure on the tire placard or in the owner’s manual.
- Check the tire cold—unused for at least three hours.
- Remove the valve cap and press the gauge firmly and straight onto the valve stem.
- Compare the reading with the specified cold pressure.
- Add air and recheck if low; release air slowly and recheck if high.
- Check at least once a month and before long trips or extra loads.
A gauge that can’t seal squarely on the valve gives a false low reading. Inspect the chuck, hose, and valve for leaks or damage before trusting any number.
Safety lines worth repeating: never set ST-tire pressure below the placard or owner’s-manual value, because underinflation builds heat and structural damage that can fail later. Never exceed the sidewall maximum. Correct pressure also doesn’t permit overloading—trailer load must stay within the manufacturer’s rating, and tire capacity must support the actual load. Confirm your gauge’s stated accuracy and calibration status, since a range figure alone guarantees nothing at every point on the dial. The guidance here applies to US road-use trailers and ST tires, not aircraft, racing, off-road, or specialty tires.
Common Questions
Is a 150 psi gauge too much for a trailer tire?
Not if it still resolves your operating pressure clearly. A 150-psi gauge gives useful headroom above an 80-psi trailer tire, but coarse markings can blur small differences at 60 psi. A fine dial or digital readout keeps low and mid-range readings accurate enough to act on.
Can I just use the pressure printed on the tire sidewall?
No. The sidewall number is the tire’s maximum cold-inflation limit, not your trailer’s recommended pressure. The correct figure lives on the trailer’s tire placard, certification label, or in the owner’s manual. Using the sidewall max as a target can overinflate a tire for its actual load.
Do dual trailer wheels need a different gauge?
Often yes. Dual-tire setups frequently have recessed valve stems that a straight chuck can’t reach squarely. A dual-head gauge is the standard recommendation there, because a gauge that can’t seat properly on the valve can report a false low pressure.
Sources
- National Highway Traffic Safety Administration. “Tire Safety: Everything Rides On It” Supports cold-measurement guidance and monthly pressure checks.
- Hankook Tire. “2024 Hankook Special Trailer Tire Warranty Guide” Source of ST Radial load-and-inflation pressure data and 80 psi load-range maximums.
- U.S. Government Publishing Office. “49 CFR §571.110 — Tire Selection and Rims for Motor Vehicles” Federal rule behind placard cold-inflation pressure and load-limit labeling.