Measuring sit-bone width means finding the center-to-center distance between your two deepest pelvic impressions on firm cardboard, then adding a posture allowance of 0–4 cm.
For the full breakdown, see our best Women’s Cycle Seat guide.
Soft cushions blur the imprint, padded shorts soften the press, and edge-to-edge marks read too wide — three small errors that turn a five-minute measurement into a saddle you return. The at-home method below takes one sheet of corrugated cardboard, a pen, and a hard chair, and it matches what Ergon recommends for getting the right saddle size.
What You Need Before You Sit Down
Five items get the job done, and none of them are specialty tools. The cardboard is the only one worth a trip to the garage.
- A hard chair or a sturdy table edge — never a sofa or a cushion-topped seat
- One piece of corrugated cardboard, roughly 10 by 12 inches
- A marker or pen
- A ruler or tape measure marked in millimeters or centimeters
- Thin, close-fitting clothing with no chamois pad
Skip the padded cycling shorts and skip jeans with bulky seams or rivets. Both distort the impressions you are about to read, per Bicycling’s fitting guidance. A hard surface matters just as much — a soft cushion spreads your weight and washes out the two indentations you need.
How Do You Take the Measurement?
Trace the two sit-bone marks, find the center of each, and measure between those centers — not between the outer edges. REI Co-op’s fitting procedure lays it out step by step.
- Set the cardboard flat-side down on the hard surface.
- Sit down with your back straight and shoulders back.
- Grip the chair or table edge and pull downward with your hands to load pressure through your pelvis.
- Hold, then stand up and look for the two clear indentations.
- Circle each impression and dot the center of each circle.
- Measure from dot to dot in centimeters or millimeters.
Check that the two impressions sit roughly level with each other before you commit to the number. An uneven press skews the reading, and a skewed reading points you at the wrong saddle width. If the marks look doubtful, redo it — Ergon’s guidance treats a repeat measurement, or a visit to a local fitter, as a sensible fallback.
Posture Changes the Number You Need
Where your pelvis tips while riding decides how much width gets added to your raw measurement. A forward road tuck loads the sit bones differently than an upright cruiser position, and each position needs its own allowance. REI’s procedure builds it in:
| Riding Position | Added Allowance | Riding Style It Fits |
|---|---|---|
| Triathlon | 0 cm | Aerobars, deep forward lean |
| Aggressive road | 1 cm | Low drop bar, fast group rides |
| Semi-aggressive road or mountain | 2 cm | Mixed road and trail |
| Commuter or urban | 3 cm | Stop-and-go city riding |
| Upright comfort | 4 cm | Cruiser, hybrid, upright bars |
Raw measurement plus allowance gives your saddle-size target in that system. Cross-check it against the brand’s own chart before buying, because published rules differ: many fitters look for a saddle roughly 15–20 mm wider than sit-bone width, while one expert recommendation cited by Bicycling puts the figure near 25 mm wider. Once you have your range, a tested women’s cycle seat roundup is an efficient way to see which saddles actually land in it.
Ergon’s saddle-fitting guide is worth reading for how width, shape, and cutout geometry interact on a women’s-specific saddle. Ergon’s sit-bone measuring guide explains why the measurement is a starting point, not a verdict.
Common Mistakes That Skew the Reading
Most bad measurements trace back to one of five errors. Any of them can add or subtract a full size from your result.
- Edge-to-edge instead of center-to-center. The measurement is between ischial tuberosity centers, not the outside rim of each mark.
- A soft seat. Couches and cushions spread pressure and hide the indentations.
- Padded or bulky clothing. Chamois pads, thick seams, and rivets create false impressions.
- The wrong torso angle. Sitting bolt upright when you ride in a forward tuck (or the reverse) puts the allowance in the wrong place.
- Uneven pressing. Two misaligned marks produce a distance that matches no saddle.
One more thing worth knowing: sit-bone width does not by itself predict comfort. Saddle shape, relief channel, and padding all matter, and women-specific saddles are built around pelvic anatomy and pressure-sensitive tissue for exactly that reason. Width narrows the field; the test ride settles it.
Common Questions
Can I measure on a carpeted floor instead of a chair?
No — carpet and padding absorb pressure the same way a cushion does, and the indentations come out shallow or invisible. Use a hard chair seat or a sturdy tabletop. The surface needs to resist your weight so the cardboard takes the full imprint of your pelvis.
Why do manufacturers recommend different amounts of extra width?
Saddle design drives it. Shape, cutout size, padding density, and shell curvature all change where a saddle supports you, so brands build their own charts. Treat any single number as a starting range and confirm against the specific saddle’s sizing guide before you order.
Do I need a professional fit if the cardboard method gives a clean result?
Not necessarily. Clear, level impressions plus the right posture allowance give you a usable target. Book a fitter if the marks look uneven, if two attempts give very different numbers, or if you have persistent pressure or numbness on rides — those are signs worth a hands-on look.
Sources
- REI Co-op. “How to Measure Sit Bones” Source of the cardboard procedure and the 0–4 cm posture allowance table.
- Ergon. “Measuring Your Sit Bone Width for the Right Saddle Size” Supports center-to-center measurement and re-measuring when results are uncertain.
- Bicycling. “How to Find the Best Women’s Bike Saddle” Clothing guidance and the roughly 25 mm wider recommendation.