Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
You already know the sound. You flip open the saddle box lid to grab a strap, the old strut gives out, and the lid drops on your wrist or your knuckles. Or you reach for the handle and find the lock cylinder spinning because the key finally stripped out. The fix is almost never a new tool box — it is the right replacement part, matched to the right number.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Weather Guard boxes run for years, but their gas struts, fasteners and locks wear at truck-bed speed. This list covers the replacements that actually match the part numbers, starting with the crowd favorite that has earned 4.5+ stars across 6,000+ owners. Read it before you order, because the most useful thing here is finding the weather guard tool box parts your specific lid was built around.
Top Picks



How To Choose The Best Weather Guard Tool Box Parts
Buying a part for a Weather Guard box is a part-number matching exercise, not a shopping spree. Get the number right and it drops on in minutes. Get it wrong and you are boxing up a set of struts that never had a chance.
Find the part number before you find the product
Every original strut has an interchange number stamped or printed on the cylinder side. Numbers like C16-11028, 21-0556-06 and 7009-2PK show up across multiple listings here, so write yours down and compare it line by line. A listing that names your number is worth more than a listing that promises a universal fit.
Measure center to center, not end to end
The extended length printed on a spec sheet is measured from the center of one ball socket to the center of the other, with the strut fully open. Measuring tip to tip gives you an oversized reading and the wrong part. Do the same for the compressed length with the lid shut.
Match the pound rating to your lid
The pound force on a lift support is the push it gives, not the weight it can lift. A 40 lb strut is built for a medium-weight lid or camper door. Two struts working together push in tandem, but they do not stack into double lift capacity for a heavy steel lid.
Check whether your box is steel or aluminum
Several replacements here are built and listed specifically for aluminum Weather Guard boxes and will not hold a steel lid up. If you are unsure which you have, check the box model family against the fitment list in the listing before ordering anything.
Side-by-Side Comparison
| Model | Best For | Extended Length | Force / Quantity | Material | Amazon |
|---|---|---|---|---|---|
| Vepagoo C16-11028 12 inch 40 Lb Gas Struts★ Best Overall | Best Overall | 12.19 inches | 40 pounds, 2 per pack | Carbon Steel | Amazon |
| ARANA C16-11028 12 inch 40lb Gas StrutsCamper Shell Pick | Camper Shells | 12.2 inches | 40 pounds, 2 per pack | Carbon Steel | Amazon |
| 21-0556-05 12 inch Gas StrutsSaddle Box Fit | Saddle Box Fit | 12.40 inches | —, 2 per pack | Carbon Steel | Amazon |
| WEATHER GUARD 9214PK Ball Socket and Nut | Genuine Mount Hardware | — | 1 count | Alloy Steel | Amazon |
| Euplokeer 12in Gas Strut 21-0556-06 | Wider Saddle Range | 12.5 inches | —, 2 per pack | Metal | Amazon |
| Truck Upfitters 12″ Gas Props | Aluminum Boxes Only | 12.2 inches | 80 pounds total, 2 per pack | — | Amazon |
| WEATHER GUARD 999-10PK Tool Box Fastener | Genuine Fasteners | — | 10 count | Alloy Steel | Amazon |
| Weather Guard 7748-2PK Replacement Locks | Keyed-Alike Pair | — | 2 locks, 4 keys | Alloy Steel | Amazon |
Detailed Reviews
1. Vepagoo C16-11028 12 inch Gas Struts
Our pick — 4.5+★ from 6,000+ verified ratings; the strongest balance of quality and price.
The set that drops onto your existing 10mm ball studs and lets the lid hold itself open.
This is the one to buy if your lid currently sags shut on your forearms. The Vepagoo C16-11028 runs 12.19 inches extended and 7.5 inches compressed, which matches the factory spec for a weatherguard husky toolbox lid. It snaps onto standard 10mm ball studs (the little ball-shaped mounting pegs the strut clips over) with no binding. Both struts ship in one pack, and the carbon steel body is finished in black.
Installation is a garage job, not a shop job. You unscrew the worn struts with a flathead screwdriver and clip the new ones onto the original mounting points. Because the strut arrives pressurized at 40 pounds, it holds your lid up on its own while you work — no propping with a broom handle, no second pair of hands.
The honest limit sits on the heavy end: a very heavy lid will overpower 40 pounds of push. A mix of buyers find the push rock steady on a standard canopy lift gate, while a smaller group say it will not hold a very heavy lid. So if your box lid is unusually weighty, move up to a stronger set instead of forcing this one. Most complaints in this category are about struts that never fit, and this one mostly dodges them.
Where it earns its place
- 12.19 inch extended length matches the factory figure for a Weather Guard husky lid, so it drops straight on
- Clips to standard 10mm ball studs with zero binding
- Two struts per pack at 40 pounds each covers a full lid swap
- Arrives pressurized, so it installs in the open position without wrestling it shut
What to weigh first
- Not the pick for an unusually heavy lid — that is a load-rating mismatch, not a fault
- You must confirm your old part number carries C16-11028 or one of its cross-references before ordering
Reach for this if: your Weather Guard husky lid needs a straight factory-spec swap and you want it done in one garage session.
Move up a tier if: your lid is genuinely heavy, because 40 pounds per strut has a ceiling.
2. ARANA C16-11028 12 inch Gas Struts
Same 40-pound push, but the fitment list is written for toppers as much as tool boxes.
Where the Vepagoo above leans on toolbox lids, the ARANA C16-11028 casts a wider net. It runs 12.2 inches extended against that strut’s 12.19 inches — a hair longer, and close enough that both land on the same factory mounting points. The compressed length is 7.5 inches, the end fittings are 10mm ball stud sockets, and each strut pushes 40 pounds (178 N) with two in every set.
What makes this set worth a look is the crossover list. It fits Leer and SnugTop camper shells, ARE truck caps, truck topper doors and canopy tops, plus fiberglass caps. For box lids it is aimed at the 32 to 45 pound weight range — light aluminum toolboxes, Weather Guard boxes, even a home-built toy box or trash bin lid you are tired of holding up.
Buyers report the install is short, taking less than five minutes with just a flathead screwdriver, and the opening and closing force feels light rather than stiff. If you are juggling a topper door on a 2016 Ram 1500 with an A.R.E. Z-Series cap, this is the strut family that keeps coming up. Its cross-reference list covers 1789sv, 24066-001, LGP6-120-40, 70092PK, 7009-2PK and weather guard 21-0370, so check your old cylinder against those before you click.
One trade-off worth naming: the 40 pound rating has a top end, and a lid at the far edge of the 32-45 pound range will feel it. Pick this for a topper or a lighter aluminum box rather than a steel saddle box lid.
The short answer: buy this if your part number cross-references to C16-11028 and the lid is a topper door or a lighter box.
Look elsewhere if: you are lifting a heavy steel lid that needs more push than one strut can give.
3. 21-0556-05 12 inch Gas Struts for Weatherguard Toolbox, 2Pcs
A longer 12.40 inch strut aimed squarely at Weather Guard steel and aluminum saddle boxes.
Length is the whole story here. This set extends to 12.40 inches measured center to center, which is longer than the 12.19 inch Vepagoo and the 12.5 inch Euplokeer set, so it slots between them. If your old cylinder carries 21-0556-05 or 7469it, this is the number to buy. The fitment list is long and specific — 125-X-01, 125-X, R-125, R-125-B, 135-X, R-135, 155-X, R-155, 117-X-01, 117, 117-X, R-117, 126-X-01, 126-X, R-126, 128-X-01 and 128-X.
Two struts ship in the box with pre-attached 10mm ball ends, an instruction guide and an after-sales card. You need a flathead screwdriver, and that is the entire toolkit. The carbon steel body is sealed against rain, snow and extreme cold, and the maker lists it as tested for 50,000+ cycles. The whole package weighs 13 ounces.
Honest read on the build: sturdiness draws a mixed response while the quality and install experience land well. That is a reasonable picture for a mid-priced strut — it does the job, and it is not the set to buy if you want the absolute heaviest-duty feel.
Best match when: your Weather Guard saddle box model appears on that fitment list and your old strut reads 21-0556-05 or 7469it.
Think twice when: your model number is nowhere on that list — cross-check before you buy, because the fit is model-specific.
4. WEATHER GUARD 9214PK Ball Socket and Nut
The small genuine piece that saves a whole strut order when the ball end is what failed.
Sometimes the strut itself is fine and the ball socket has worn or the nut has gone missing. This is the Weather Guard factory part for that exact problem — the 9214PK ball socket and nut in alloy steel. It is a genuine piece, sourced as a single unit rather than a pair, so it fixes one mounting point at a time.
The package is listed at 4.51 pounds, which tells you this is a hardware kit with real weight to it rather than a plastic bag of clips. The nut and socket are what hold the strut end to the box, so when the factory hardware is stripped or snapped, a replacement strut alone will not clip on. That is the gap this part fills.
There is no customer review text on this listing to lean on, so judge it on the spec sheet and the part number: 9214PK, genuine Weather Guard, alloy steel. Match that number to your old hardware and you have your answer. It is the least glamorous part here, and often the one that actually fixes a sagging lid.
The practical case: every strut on this list clips onto a 10mm ball stud, and if the stud or its nut is stripped, none of them will hold. Buy the hardware before you assume the strut is dead.
Buy it when: your strut is good but the ball end or nut has failed or gone missing.
Skip it when: your mounting hardware is intact and the strut body itself has lost its push.
5. Euplokeer 12in Gas Strut
The longest of the steel-and-aluminum toolbox struts here, and the one with the broadest model list.
At 12.5 inches extended, this Euplokeer set is the longest strut on the list — a half inch beyond the 12.2 inch ARANA and Truck Upfitters pairs. If your old cylinder reads 21-0556-06, 7467IC or 7009-2PK, that extra length is exactly what the factory wanted. It is built for Weather Guard steel and aluminum saddle boxes, and the fitment list runs deep: 121-X-01, 123-X-01, 123, 123-X, 127-X-01, 127, 127-X, R-127, 131-X-01, 137-X-01, 137, 137-X, 147-X-01, 154-X-01 and 6212-5.
Owners describe the push as solid and the lid stability as the thing they notice — the lid stays where you leave it instead of drifting down. Fit and install get the same warm read. Two shocks come in the listing and go on with a flathead screwdriver. Euplokeer backs it with 24 hour email response and a 15 month product exchange.
One caution worth heeding: the maker states plainly that this shock is not compatible with every toolbox on the market. Read your model number against the list — not the general description — before ordering. That one check is what separates a five-minute strut swap from a return label.
Worth it for: Weather Guard saddle box owners whose part number appears on that long fitment list.
Not the right call if: you are guessing at the fit — the maker warns this does not suit every box.
6. Truck Upfitters 12″ Gas Props
Two 40-pound props that add up to 80 pounds of push — and four spare ball mounts in the box.
Here is the clearest split on this list. This Truck Upfitters pair fits Weather Guard aluminum truck bed toolboxes only, covering models 121-0-01, 121-5-01, 123-0-01, 123-5-01, 127-0-01, 127-5-01, 131-0-01, 131-5-01, 137-0-01, 137-5-01, 147-0-01, 147-5-01, 154-0-01 and 154-5-01. The maker states outright that it will not hold a steel box lid. If you have a steel box, keep walking to one of the steel-rated sets above.
Each prop carries 40 pounds, for 80 pounds total across the pair — but the maker is careful to note that does not mean it lifts an 80 pound object. The typical hinged door this suits runs about 50 to 70 pounds, counting the camper shell locks and keys. Extended length is 12.2 inches and compressed is 7.5 inches, both measured center of ball mount to center of ball mount.
Outside the truck bed, the included four 10mm ball mounts open up camper and canopy windoors, RV doors and awnings, boat hatch lifts, cabinet struts and storage bed lifts. The measurement warning is real: these props cannot be compressed by hand and must be installed in the extended, open position. Measure your old strut fully open and fully closed before ordering, and allow for the maker’s stated 1-5% size variation.
What buyers get right: the fit and install experience lands well on aluminum Weather Guard boxes, and the build feels solid. The extra ball mounts are the quiet bonus — they turn a one-job prop set into spare hardware for RV doors and boat hatches later.
What to respect: installation only works in the open position, and a wrong measurement is the number one way this goes back.
Pick this when: you run an aluminum Weather Guard bed box or a camper shell door in the 50-70 pound range.
Don’t pick this when: you have a steel box lid — the maker is explicit that it will not hold.
7. WEATHER GUARD 999-10PK Tool Box Fastener
A ten-piece pack of genuine Weather Guard fasteners for the hardware a swap quietly eats.
Every strut swap turns up a missing bolt or a stripped original fastener, and that is what this pack is for. It is the genuine Weather Guard 999-10PK fastener set in alloy steel, ten pieces to a unit. The finish is water repellent, which matters when the hardware lives in a truck bed and sees rain and road spray. Color is listed as black and gray.
There is no review text on this listing, so the spec sheet is your source: model 999-10PK, alloy steel, ten count, water repellent. It is one of the pricier items on this list for the piece count, which makes sense — these are factory parts in a bulk pack, not a bag of generic bolts from a hardware bin.
Who is this for? The box owner replacing a strut, a hinge or a latch and finding the original bolts are past saving. Keep a pack on the shelf and a strut swap never stalls because one original bolt snapped. skip it if your hardware is intact and you only need the lift support itself.
Worth having: if your Weather Guard box hardware is worn, stripped or rusting and you want genuine parts on hand.
Not needed: if you are only swapping struts and your existing fasteners are sound.
8. Weather Guard 7748-2PK Replacement Truck Tool Box Locks
Two locks that open on the same key, so one ring runs every box on the truck.
When the key finally spins in the cylinder, this is the fix that ends the daily fight with your lid. The 7748-2PK gives you two Weather Guard locks keyed alike, plus four keys and the mounting parts. One key opens both locks, so a saddle box and a chest box on the same truck stop demanding separate keys.
Fit is the selling point. It is listed as compatible with saddle boxes, lo-side boxes, all-purpose chests, pork chop boxes and cross boxes. The body is alloy steel with a polished black finish, and the manufacturer describes the control as a touch-and-hand type. Mounting parts are in the box, so the swap runs a few minutes rather than an afternoon.
Owners mention the locks go in fast and fit cleanly, and the security feels like the original. Cold weather is the test most locks fail, and this one has been noted to work in 10-degree icy conditions — that is the kind of detail that matters if your truck lives outside in winter. The four keys across two locks cover the household and the spare set in the glovebox.
Why it tops the security slot: keyed-alike convenience plus genuine Weather Guard build is a combination no generic lock set matches. You are paying for the factory fit and the matched key.
The one caveat: confirm your box family is on the compatibility list before ordering, since the lock is designed for the Weather Guard range specifically.
Choose this if: your lock has failed and you want one key for two Weather Guard boxes.
Pass if: your current locks are still smooth — this is a replacement, not an upgrade you need yet.
Know the Specs
Extended and compressed length
These two numbers are measured from the center of the ball socket on one end to the center of the ball socket on the other. Extended length is with the strut fully open and compressed is with it folded shut. Measure your old strut the same way, because a tip-to-tip reading runs long and lands you on the wrong part.
Pound force rating
The pound figure printed on a strut is the push it gives, not the weight it can lift. A 40 pound strut suits a medium-weight lid or camper door. Two struts push together but do not double into lift capacity for a heavy steel lid, so match the rating to your lid’s real weight.
Interchange and OEM numbers
Cross-reference numbers are the shorthand the industry uses to identify a strut. C16-11028, 21-0556-05, 21-0556-06, 7009-2PK and 7467IC all appear on this list. Find the number stamped on your old cylinder and match it against the listing’s cross-reference list before ordering.
Ball stud size and hardware
Most of these struts clip onto a 10mm ball stud — a small ball-shaped peg mounted on the box and lid. If the stud or its nut is stripped, the strut will not hold no matter how new it is. That is when you reach for a ball socket and nut like the Weather Guard 9214PK instead of another strut.
Common Questions
How do I find the right replacement strut for my Weather Guard box?
How do I measure a gas strut — center to center or end to end?
Will a 40 lb gas strut hold up a steel tool box lid?
Can I install gas struts myself or do I need a mechanic?
Why is my new strut not holding the lid up anymore?
Are these struts compatible with Leer ARE and Snugtop camper shells?
Do keyed-alike Weather Guard locks fit every tool box model?
What is the difference between a gas strut and a ball socket and nut?
How long does a Weather Guard replacement part typically last?
The Bottom Line
For most Weather Guard owners, the weather guard tool box parts purchase that solves the falling lid is the Vepagoo C16-11028 12 inch 40 Lb Gas Struts, because its 12.19 inch extended length and 10mm ball stud mounting match the factory spec. If you need a longer-reach set for a saddle box, the Euplokeer 12in Gas Strut runs 12.5 inches extended with its own deep fitment list. And for the owner whose key ring has grown past one cylinder, the Weather Guard 7748-2PK locks give you two boxes on a single key. One last note: the top pick has more reviews behind it than most items here, but the genuine Weather Guard locks hold the highest rating on the list — if security is your concern, buy both.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.




