Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
Your grill still lights, but the bars over the burners have gone the color of old pennies and flake when you touch them. The picks below are all genuine Weber-compatible flavorizer bars in the 15.3-inch and 22.5-inch and 24.5-inch lengths, and every one of them is matched to a specific grill family so you buy the right set the first time.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Length is the number that sinks most orders, so measure the longest bar you are pulling out before anything else. Below you will find the length, thickness, and material each set actually uses, so the pick you land on is the one that fits your burners and your flavor expectations. The right set of weber grill flavorizer bars is the one that drops straight into your cook box and stays level.
Top Picks


How To Choose The Best Weber Grill Flavorizer Bars
Flavorizer bars do two jobs at once. They sit between the burner and your food to block direct flame, and they catch the fat and marinade that drips down. That dripping liquid burns off on the hot metal and the smoke curls back up into the meat. Get the fit wrong and neither job happens properly, so the buying decision depends on a short checklist.
Match the length to your grill family first
The length is the single number that decides whether a set fits at all. Measure the longest bar you are replacing, then compare it to the listed length of the set. A 15.3-inch bar is built for the Spirit 200 and 300 families with front-mounted control knobs, while the 22.5-inch and 24.5-inch bars serve older Spirit 700 and Genesis Silver and Genesis 300 grills with side controls. A bar that is even slightly too long will not sit flat, and one that is too short lets flame lick around the edges.
Thickness tells you how long the set lasts
Thickness is written as a gauge number, and lower means thicker steel. Most of these sets use 16GA porcelain-enameled steel, which the makers describe as thicker than common 17GA to 20GA plates. Thicker steel resists bowing when the burner runs hot underneath it, and it holds its shape so the grease and smoke do the same thing across the whole cooking surface. If you grill most weeks, that extra mass is the part you notice after a few seasons.
Side-by-Side Comparison
| Model | Best For | Length | Count | Material | Amazon |
|---|---|---|---|---|---|
| Grill Flavorizer Bars for Weber Genesis E310 E320 E330 7540 7539★ Best Overall | Genesis 300 series with side controls | 24.5 in | 5 bars | 16GA porcelain steel | Amazon |
| 7635 15.3 Inch Flavorizer Bars for Weber Spirit I & II 200 SeriesBest Value | Spirit 200 series with front knobs | 15.3 in | 3 bars | 16GA porcelain-enameled steel | Amazon |
| 7635 & 67045 Upgraded Flavorizer Bars for Weber GS4 Spirit II E-210 | Spirit II GS4 with cut-out flame checks | 15.3 in | 3 bars | 16GA porcelain-enameled steel | Amazon |
| Spirit E310 Parts 15.3″ Flavorizer Bars for Weber Spirit 300 Series | Spirit 300 series three-burner grills | 15.3 in | 5 bars | 16GA porcelain-enameled steel | Amazon |
| 7636 Upgraded Flavorizer Bars for Weber Spirit 2 Parts | Notched bars for flame observation | 15.3 in | 5 bars | 16GA porcelain-enameled steel | Amazon |
| 67046 & 7636 Flavorizer Bars for Weber Spirit II E-310 310 300 | Spirit 300 series with star-glaze enamel | 15.3 in | 5 bars | 16GA porcelain-enameled steel | Amazon |
| Leship 22.5″ Flavorizer Bars Replacement for Weber 7536 65903 | Older Spirit 700 and Genesis Silver grills | 22.5 in | 5 bars | 304 stainless steel | Amazon |
Detailed Reviews
1. Grill Flavorizer Bars for Weber Genesis E310 E320 E330 7540 7539
Our pick — 4.5+★ from 7,500+ verified ratings; the strongest balance of quality and price.
Five thick 24.5-inch bars that put the mass back over a hot Genesis burner.
If you own a Genesis 300 series grill with the knobs on the side, this is the set that matters — it replaces the Weber 7539 and 7540 heat plates and measures 24.5 inches long. The length is what separates it from the 15.3-inch Spirit sets further down this list, and the width runs 2.375 inches against the 3.5 inches on the GS4 Spirit II bars. That narrower profile is built for this specific cook box.
The build is the selling point. Each bar is 16GA porcelain-enameled steel, which the maker describes as thicker than the common 17GA to 20GA plates, and the whole set weighs 9.38 pounds against 3.56 pounds for the 7635 Spirit 200 set. That extra mass is what keeps the bars flat over a hot burner instead of bowing and letting flame through. The Snow Point porcelain-enameled finish is there to resist chipping and flaking under high heat, and the smooth face wipes down easier than a rusted original.
Buyers consistently report an exact fit that makes a tired Genesis cook like new again. The one thing to weigh is that this is a five-bar set built heavy on purpose, so it is not the bargainer’s route to a 15.3-inch Spirit grill. Different animal entirely.
What Earns The Top Slot
- 24.5-inch length sized for Genesis 300 series grills with side control knobs
- 16GA porcelain-enameled steel, thicker than common 17GA to 20GA plates
- 9.38-pound set with real structural weight behind it
- Replaces Weber 7539 and 7540 porcelain steel heat plates directly
- Snow Point enamel finish built to resist chipping, peeling, and flaking
Where It Won’t Suit You
- Won’t drop into a 15.3-inch Spirit 200 or 300 cook box
- Heavier set to lift out when you deep-clean the grill
Goes straight in if: your Genesis 300 side-control grill has been running on bowed, flaking plates and you want the heaviest direct replacement here.
Look elsewhere if: you are working a Spirit 200 or 300 — you need the 15.3-inch size, not this one.
2. 7635 15.3 Inch Flavorizer Bars for Weber Spirit I & II 200 Series
The three-bar fix for a two-burner Spirit 200 — small kit, low outlay, exact fit.
Owners of a two-burner Spirit E-210 or S-210 with front-mounted knobs get exactly the parts they need here, without paying for bars their cook box cannot use. The set is three bars at 15.3 inches long, 3.5 inches wide, and 2.5 inches tall. It replaces Weber 67045 and 7635 and covers the 2013-and-newer Spirit I and II 200 series, including the E-220 and S-220.
The fit is why this set earns its spot: it drops in clean with no fuss, the failure point on most off-brand parts. The 16GA porcelain-enameled steel is claimed to outlast other heat plates, and the smooth face wipes down fast with a grill brush and soapy water. It protects the burner from fat and oil while the evaporating drippings do their work aromatizing the meat and vegetables.
Where you should temper expectations is long-term corrosion. This set is widely liked for sturdiness and install, but the honesty note in the reviews is that the bars will eventually rust through. Treat that as the natural life of an enameled steel part rather than a fault — the fit and the price are what carry it. That is a fair trade for a grill you plan to keep cooking on.
Fit is the whole story: this is a direct replacement for the 67045 and 7635 bars on front-control Spirit 200 grills, and that fit is what owners value most about it.
The trade-off worth knowing: enameled steel is a wear part here — expect the bars to rust out eventually rather than last forever, and plan on that cycle.
Made for: the two-burner Spirit E-210 or S-210 owner who wants a straight swap without overspending.
Hold off if: you have a three-burner Spirit 300 — this three-bar kit is not built for that cook box.
3. 7635 & 67045 Upgraded Flavorizer Bars for Weber GS4 Spirit II E-210
Four cut-outs in every bar turn flame-checking into a glance instead of a guess.
Here is the feature no other set on this list offers: each bar has four cut-outs so you can see the burner flame while you cook. If you like to run the knobs by feel and by eye, those little windows make it easy to spot a lazy burner or a hot spot mid-session. The set fits Spirit II E-210, S-210, and E-220 grills on the GS4 platform, plus the older front-control Spirit 200, 210, and 220 models.
You get a bar that holds its shape because it is solid cast steel, shaped before the porcelain enamel (a glass-like coating that resists rust) goes on. The numbers back that up: the set weighs 3.36 pounds, with each bar at 1.12 pounds. Each one measures 15.3 inches long by 3.5 inches wide by 2.5 inches tall, and it cross-references Weber 67045, 7635, and 69796 (the part numbers it replaces). Buyers report a heavy-duty feel and an easy drop-in, with vaporized grease and juice off the hot bars bringing the smoky flavor back.
The thoughtful part is the surface finish — it is dark and smooth, which the maker ties to corrosion resistance under high heat. What separates this from the plain 7635 set is the cut-out design and the cast-steel build; what it shares is the same 15.3-inch footprint. If your grill lives outside year-round, that combination of smooth enamel and heavier bars is the more forgiving choice.
Why It Stands Out
- Four cut-outs per bar let you watch the burner flame directly
- Cast steel formed before enameling, at 1.12 pounds per bar
- Cross-references Weber 67045, 7635, and 69796
- Fits GS4 Spirit II 200 series and older front-control Spirit 200/210/220
The Honest Limits
- Only a three-bar kit — not for three-burner Spirit 300 grills
- The cut-outs add viewing windows, not extra heat protection
Worth grabbing if: you want to eyeball your flame through the bars while you dial in temperature on a GS4 Spirit II.
Not the one for: a Spirit 300 owner — the three-bar count and 15.3-inch size are matched to the 200 series.
4. Spirit E310 Parts 15.3″ Flavorizer Bars for Weber Spirit 300 Series
A five-bar kit sized for three-burner Spirit 300 grills that need full coverage.
The number that decides this one is five. Three-burner Spirit 300 and Spirit II 300 grills need full-span coverage, and this pack throws in a complete set of five bars at 15.3 by 2.6 by 2.5 inches. It covers Spirit E-310, E-315, E-320, S-310, S-315, and S-320, plus the Spirit II LX 300 series and GS4 Spirit II grills, and it cross-references Weber 67046, 69797, and 68843.
It takes high heat under three burners without twisting, because the steel is 16GA thick (a gauge measure where a lower number means thicker metal) with a porcelain-enameled finish. The maker claims it is sturdier than 17GA or 20GA heat plates. Cleanup stays manageable thanks to the smooth non-stick surface: grill brush and soap, then dry it fully with a towel before it goes back in. Buyers praise the precise drop-in fit, and the finished grill looks and cooks right again for far less than a new one.
One thing to note about the size difference: these bars are 2.6 inches wide where the Genesis set is 2.375 inches, and 2.5 inches tall against the Genesis 2.375 inches. That is a real gap in footprint between two families, which is exactly why you check your model number rather than eyeballing it. Buy for the grill you actually have.
Built for the three-burner: a full five-bar set covering the Spirit 300 and Spirit II 300 — E-310 through E-320 and the S-versions — in 16GA enameled steel.
Check before you click: confirm you are on a 300 series and not a 200, because the bar count and dimensions are set for the wider cook box.
Right call for: Spirit 300 and Spirit II 300 owners who want all five bars replaced in one go.
Wrong call for: a two-burner Spirit 200 — you only need three bars and a shorter footprint.
5. 7636 Upgraded Flavorizer Bars for Weber Spirit 2 Parts
Two notches per side let the burner breathe and the flame show through.
Five bars at 15.3 inches, but the design is the part worth explaining. Each bar carries four notches — two on each side — that help heat spread more evenly and let air move so the burner burns cleaner. They also open a sightline to the flame, so checking the burners means glancing down instead of lifting a bar off a hot grill. The set replaces 67046, 69797, 68843, and 7636 on Spirit and Spirit II E-310, E-330, S-310, and S-320 grills with front-mounted controls.
The 16GA porcelain-enameled steel is the same material spec the other Spirit 300 sets use, which keeps the protection story consistent: grease drips hit the bar, the burner stays shielded, and the vapor does the flavor work. Owners put the fit at the top of the list of what works here, and the bars have held up through a couple of winters for at least one long-term user. Install is a simple swap once you have confirmed your model.
The caution is the one that catches everyone on this list — the listing also carries the part number 7736, and the cross-reference has to line up with your exact Spirit series before you order. Double-check the series and the 15.3-inch dimension against the bar you are pulling out. Do that and this set goes in without drama.
What The Notches Buy You
- Four notches per bar for even heating and better airflow
- Clear view of the burner flame without removing a bar
- Five 16GA porcelain-enameled bars in one pack
- Replaces 67046, 69797, 68843, and 7636
What To Watch For
- Series and dimension check is on you before ordering
- Built for front-control Spirit 300 grills, not the 200 series
Pick it when: you want a flush five-bar replacement for a front-control Spirit 300 and like the idea of seeing the flame through notched bars.
Pass it up when: your grill is a Spirit 200 — the bar count and length here are aimed at the three-burner setup.
6. 67046 & 7636 Flavorizer Bars for Weber Spirit II E-310
A star-glaze enamel finish that holds its thermal stability through heavy weekly use.
This is the set for the Spirit 300 owner who grills most weeks and wants the enamel to hang on. The maker applies a star glaze over the porcelain, which it says strengthens the thermal stability of the coating. In plain terms, the finish is built to stay put when the metal heats and cools over and over. The set is five bars at 15.3 by 2.6 by 2.5 inches, and it fits Spirit II 300 series from 2017 on as well as Spirit 300 series from 2013 to 2017 with front controls.
The weight backs up the claim — the whole set runs 4.76 pounds at an average 1.50 mm thickness, which is 16GA steel. That heft is what keeps the bars from chattering or bowing when three burners are running hot beneath them. Each bar also has four cut-outs for reading flame status and warming up faster, and the bars are designed to absorb and radiate heat evenly once they are in. It replaces Weber 67046, 7636, 69797, and 68843.
Owners keep coming back to the fit and the solid feel: the bars drop in and the old grill looks and cooks close to new. The one real check is your year range: this set fits Spirit and Spirit II 300 series, so confirm your model year before ordering.
Finish first: the star-glaze porcelain-enameled coating is what separates this from the plainer Spirit 300 sets, and the 4.76-pound build gives it the mass to hold steady over three burners.
The one thing to confirm: year range matters here — the set covers Spirit and Spirit II 300 series across the 2013-to-2017 and 2017-and-newer builds, so match your grill year before you buy.
Fits your plan if: you are replacing bars on a Spirit 300 and want a heavier set with the star-glaze finish and four flame cut-outs.
Not your set if: you own the two-burner Spirit 200 — this five-pack is designed around the three-burner cook box.
7. Leship 22.5″ Flavorizer Bars Replacement for Weber 7536 65903
Scale, not chrome — steel that comes out clean instead of crusted and flaking.
For the older-gas-grill crowd, this is the material argument. These bars are 304 stainless steel, which the maker describes as corrosion resistant, non-magnetic, and more durable than bars made from magnetic materials. Five bars, each 22.5 inches long by 2.3 inches wide by 2.3 inches tall, replace Weber 7536, 7537, and 65903 across Spirit 700, Weber 900, Genesis Silver B/C, Genesis Gold B/C, and Genesis Platinum B/C grills. The set also covers Spirit 300 series models with side-mounted control panels.
Size is where the focus should be, because this is the longest set here at 22.5 inches, and it is built for a specific generation of grills. The maker’s own advice is the right advice: double-check your grill model and measure the longest bar you are replacing before you order. A 15.3-inch Spirit II bar is a different beast entirely, and the 22.5-inch length will not sit right in that cook box. Get the measurement right and the stainless construction is the part that pays off, because it wipes clean and resists the crust that eats enameled steel over time.
Here is what to plan for. Stainless is tougher against corrosion, but these bars have a mixed reputation on thickness and an occasional report of warping under high heat. That is not a reason to dismiss them — it is a reason to run them on a grill you do not hammer at maximum temp. The durability story is what people value most, and on a Genesis Silver B that sees steady weekend duty, that is the right trade.
Why stainless earns a slot: 304 stainless construction across five 22.5-inch bars, made for Spirit 700 and Genesis Silver B/C era grills that already ate through one set of enameled plates.
What you are signing up for: the thickness reads differently to different owners and a few report warping under sustained high heat, so this set rewards moderate cooking temps and occasional care.
Reach for it if: you are running a Genesis Silver B/C or older Spirit 700 and want stainless steel instead of another enameled set.
Leave it if: your grill is a 15.3-inch Spirit II or Spirit 300 — that is a different cook box with different bar dimensions.
Know the Specs
Gauge (16GA Steel)
Gauge is how steel thickness is written, and with each higher number the steel gets thinner. The sets here use 16GA, which the makers describe as thicker than common 17GA to 20GA plates. Thicker steel resists bowing over a hot burner and holds its shape so heat spreads the same way across the cook box. That is why a heavier set tends to hold up through more seasons of weekly grilling than a thin plate does.
Porcelain-Enameled vs 304 Stainless
Porcelain-enameled steel is a steel core with a glass-like coating fired onto the surface, and the coating is what pushes back against rust and makes the bar easy to clean. It is a wear part, so eventually it can flake. And 304 stainless steel is a corrosion-resistant metal through and through, with no coating to chip. Enameled steel tends to be the value path, while stainless is the longer-view choice for older grills that run hot and wet.
Common Questions
How do I know which flavorizer bar length my Weber needs?
Do flavorizer bars fit both the Spirit 200 and the Spirit 300?
Is 16GA steel thick enough for a grill used every week?
What is the difference between porcelain-enameled and stainless steel flavorizer bars?
Why do some flavorizer bars have cut-outs and others do not?
How often should I replace my flavorizer bars?
Will a flavorizer bar set for a Genesis fit my Spirit grill?
Can I clean flavorizer bars and reuse them instead of replacing?
Do I need the same number of bars as my grill had originally?
The Bottom Line
For most people, the weber grill flavorizer bars winner is the Grill Flavorizer Bars for Weber Genesis E310 E320 E330. It earns that spot with the heaviest 16GA build on the list at 9.38 pounds, in the 24.5-inch size a Genesis 300 side-control grill needs. If you are on a Spirit 200 or Spirit II GS4 and want flame cut-outs, grab the 7635 & 67045 Upgraded set. And for an older Genesis Silver B/C or Spirit 700, the Leship 22.5-inch 304 stainless set is the one to reach for. Measure your longest bar first — the right length is what turns a good set into a grill that cooks like new.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.




