How to Choose the Right Wheel Chock Size for Your Motorcycle | Tire Fit Comes First

Match the chock to your front tire’s width and rim diameter, then confirm its load rating exceeds your bike’s fully loaded weight.

Most riders buy a chock that looks right and later find the front tire won’t seat or the fender kisses the cradle. The deciding numbers live on your tire sidewall — not the chock’s box. Match those to the chock’s published ranges and you save a return shipment.

Four things decide fit: front-tire width, rim diameter, motorcycle weight, and where the chock will live (garage, trailer, or truck bed). Align all four and the chock works. Miss one and you’re wrestling a bike that rocks, sticks, or won’t roll in.

What Measurements Decide Whether A Chock Fits?

Tire width and rim diameter make or break the fit. Load rating comes third — and it’s the one people skip.

Read the front tire sidewall and record the full size: width, aspect ratio, and rim diameter. A 120/70-17 isn’t the same fit as a 150/80-16. Chock makers publish tire-width ranges in millimeters and rim ranges in inches, so translate your sidewall numbers before comparing.

  • Tire width: the chock’s maximum must exceed your tire’s width in mm.
  • Rim diameter: must fall inside the chock’s published inch range.
  • Load rating: must exceed your motorcycle’s wet, fully loaded weight — not the dry brochure figure.

Harley-Davidson’s Cruiser Cradle Wheel Chock, for example, supports up to 3,000 lb, front and rear rim diameters from 14–22 in, and tire widths from 80–220 mm. Sealey’s WC06.V2, WC07.V2, and WC08.V2 carry maximum tire widths of 95 mm, 140 mm, and 165 mm respectively.

How Do You Match A Chock To Your Bike And Its Job?

A garage stand and a trailer cradle are not the same purchase. A storage chock holds the bike upright so it doesn’t tip; a transport chock must keep the front wheel locked while the trailer bounces. Harley-Davidson sells its cradle chock for trailer use only, and even then it isn’t a complete restraint system — tie-downs still do the securing. Northern Tool’s manual describes its chock mounting to a truck bed, trailer, or concrete floor, and requires confirming wheel fit before first use.

Adjustable chocks earn their price when one chock serves more than one motorcycle, but the adjustment must seat the tire against the front stop without binding. Harley-Davidson’s fit table maps cradle positions to tire-and-rim combinations — a 100 mm front on an 18-inch rim calls for position 2/3, while a 150 mm or wider front calls for 1/1. Start from the maker’s recommended position, not guesswork.

Clearance is where low-fender cruisers and faired bikes run into trouble. Harley-Davidson warns that very low fenders or cowlings may prevent fit entirely, and calls for 15 in of clearance at the front stop channel plus 6 in for the engaged cradle. Measure your fender-to-ground gap before ordering.

Chock Model Published Fit Range Best For
Harley-Davidson Cruiser Cradle Up to 3,000 lb; 14–22 in rims; 80–220 mm tires Trailer transport of cruisers
Sealey WC06.V2 Up to 95 mm tire width Narrow front tires only
Sealey WC07.V2 Up to 140 mm tire width Standard sport and naked bikes
Sealey WC08.V2 Up to 165 mm tire width Wider front tires, light cruisers
Northern Tool chock 16 lb unit; 20-1/2 × 10-3/8 × 13-1/5 in folded Truck bed, trailer, or shop floor

The Harley-Davidson documentation spells out mounting torque and hole size if you’re bolting one down, and it’s worth reading before you drill. To compare ready-made options, this roundup of tested wheel chocks for motorcycles covers models that hold up in real use.

What Mistakes Cause A Chock To Fail?

Buying by wheel diameter alone is the most common error. Tire width is what actually jams or frees a cradle.

Other failures repeat predictably: treating a parking chock as a full trailer restraint (a chock holds the wheel upright; straps hold the bike down), using a chock rated below the bike’s loaded weight, failing to bolt the chock to the deck or floor so it walks under load, assuming “universal fit” without checking fender and cowling clearance, and driving a bike into a cradle that’s too tight so it won’t seat fully or components get damaged.

On the Harley-Davidson unit, align the wheel with the cradle center, push it in until the tire rests against the front stop, then check for excessive tightness, rocking, or fender contact. If the wheel sticks, Harley-Davidson says switch to the secondary cradle position. Transport chocks use 3/8-in mounting holes, and the adjustable V-bracket screws tighten to 8–9 ft-lb.

Seat it well and the front wheel sits locked, the fender clears, and the bike rolls out without a fight.

Common Questions

Can one chock fit two different motorcycles?

Yes, if it’s adjustable and both bikes’ tire widths and rim diameters fall inside the published ranges. Reset the cradle position between bikes and confirm each seats without binding before trusting it in a trailer.

Is tire width more important than wheel diameter?

Both matter, but width most often disqualifies a chock. Two tires can share a 17-inch rim yet differ by 40 mm in width, and the wider one may exceed the cradle’s maximum. Check width first, then confirm the rim range.

Do I still need tie-downs with a wheel chock?

Yes. A chock holds the front wheel upright and keeps it from turning, but it does not secure the motorcycle for transport. Harley-Davidson frames its cradle chock as trailer hardware that works alongside additional restraint, not a replacement for straps.

Sources

Scroll to Top