A pool filter traps suspended debris as the pump pushes water through sand, pleated fabric, or DE-coated grids, then returns the cleaned water to the pool.
Filtration is mechanical, not chemical — chlorine or another approved sanitizer handles microorganisms, while the filter pulls out dirt, pollen, and fine suspended particles. Pentair’s homeowner documentation describes all three filter types the same way: the pump sends water through a netting, membrane, or sand medium that captures debris before it circulates back.
Here’s how each type works, how often it needs attention, and the mistakes that quietly wreck filter performance.
How Do Sand, Cartridge, and DE Filters Actually Differ?
The difference comes down to the medium water passes through and how that medium gets cleaned — backwashing for sand, rinsing for cartridge, and recoating for DE. Sand pushes water through a bed of graded filter sand that traps dirt between the grains, then releases it through internal laterals. Cartridge filters run water through pleated fabric, where the pleats create a large surface area for catching debris. DE filters coat fabric grids or cartridge elements with diatomaceous-earth powder, and water passes through that coating.
The filtration ranges aren’t close. Pentair’s published comparison lists rough figures of under 5 microns for DE, 10–30 microns for cartridge, and 20–100 microns for sand. Finer filtration means clearer water, but it also means more frequent service.
| Filter Type | Filtration Range | Cleaning Method |
|---|---|---|
| Sand | 20–100 microns | Backwash |
| Cartridge | 10–30 microns | Remove and hose off |
| DE (grids or cartridges) | Under 5 microns | Rinse and recoated with pool-grade DE |
| Cartridge-style DE | Under 5 microns | Remove four cartridges, rinse, resoak |
| Sand backwash valve | Six-function, 1½-inch multiport | Rotate to reverse flow |
What Decides When a Filter Needs Cleaning?
Your pressure gauge decides, not the calendar — record the clean starting pressure after installation or a full cleaning, then watch for the rise. Pentair recommends cleaning a DE filter at roughly 10 psi above the original starting pressure or when flow falls noticeably. The Clean & Clear Plus cartridge line gets the same 10 psi trigger, while the Clean & Clear RP guidance uses 8–10 psi above starting pressure.
Cartridge cleaning frequency has no universal interval. Season length, debris load, pool type, and filter design all shift the schedule, so a clean starting number plus a rising gauge beats any fixed monthly rule.
Which Mistakes Cause the Most Pool Filter Problems?
The biggest offender with DE is running the filter without coating its grids, and the second is overdoing the coating. Pentair warns that excess DE can bridge between elements and plug the filter outright. Pool-grade DE only — the wrong powder clogs rather than coats.
- Backwashing a cartridge filter, which is designed for rinse-and-reinstall, not reverse flow
- Choosing a filter by tank size alone instead of matching flow rate, plumbing diameter, pump output, and pool volume
- Cleaning cartridges with too much pressure or bending the pleats
- Ignoring climbing pressure or weak return flow until the pump strains
- Releasing DE-laden wastewater where local rules ban it
If you’re still comparing options, this roundup of water filtration for swimming pools sorts the trade-offs by pool size and pump setup.
How Do You Clean and Restart a Filter Safely?
Power off first, relieve pressure second, and open the tank only after the gauge reads zero. Pentair’s safety guidance is blunt about trapped pressure — it can make filter components hazardous. Place any automation in service mode, shut off power to all pool equipment, and open the manual air-relief valve before touching a tank, pump strainer, or air-relief system.
For DE service: shut off the pump and controls, open the air-relief valve, open the waste drain where applicable, remove the element assembly, rinse with a garden hose, clean the tank and O-ring groove, and reinstall the element fully seated. Recoat only with the manufacturer-specified amount of pool-grade DE. Pentair also advises manually cleaning a System 3 DE module at least twice yearly and soaking it in filter-cleaning solution at least annually. For cartridge elements, pull the element, hose it down while rotating it, and reseat it completely before restarting.
If it doesn’t, or the tank leaks, shut the pump off immediately — don’t investigate a leak under pressure. Turn off power, open the air-relief valve, stand clear, and wait for zero.
Common Questions
Does a pool filter sanitize the water?
No. Mechanical filtration only pulls out suspended debris like dirt and pollen. Killing bacteria and other microorganisms requires chlorine or another approved sanitizer. A clean filter reduces the load on your sanitizer, but it never replaces it.
Can I use regular diatomaceous earth in a pool filter?
No. Pentair specifies pool-grade DE only. Other grades are not formulated for filter coating and can clog the grids or cartridges instead of coating them properly. Overfilling is just as risky — excess powder can bridge between elements and block the filter entirely.
How often should a cartridge filter be cleaned?
There is no universal interval. Cleaning frequency depends on season length, debris load, pool type, and the filter’s design. Record the clean starting pressure and clean the element whenever the gauge climbs about 8–10 psi above that number, or when return flow weakens noticeably.
What sand capacity do Pentair Sand Dollar models need?
Sources
- Pentair. “How Your Pool Works” Describes how pool filters use sand, membrane, or netting media to remove debris and explains filtration’s role alongside sanitizers.