Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
If your dishwasher ends a cycle with a single hard thump inside the wall, a water hammer arrestor is the part that absorbs it. The right one is a small shock-absorbing chamber you screw onto the 3/8-inch supply line, and it costs far less than opening up drywall. This list covers eight arrestors that actually fit dishwasher supply lines, sorted by what each one does best.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
A quick honesty note before you scroll: this list uses flexible, human-like matching for dishwasher supply line use, so not every pick is the exact part number you searched. If a 3/8-inch compression arrestor sized for an appliance line is what you need, the nearest same-type unit serves the same purpose. Here is the honest breakdown of the water hammer arrestor for dishwasher market.
Top Picks



How To Choose The Best Water Hammer Arrestor for Dishwasher
The bang you hear is a pressure spike, not a mechanical fault. When the dishwasher solenoid valve snaps shut, the moving water column stops instantly and that energy has to go somewhere. A water hammer arrestor gives it a cushioned pocket to expand into, so the pipe stops slamming against the studs.
Match the connection before anything else
Most dishwasher supply lines and angle stops in the United States use a 3/8-inch compression fitting. A 3/8-inch male compression on one end and a 3/8-inch female compression on the other is the shape that screws straight onto an existing stop valve. Buy the wrong thread and no amount of chamber volume will help, because the part simply will not seat.
Check the pressure and temperature rating
The arrestor has to survive the same water your house already pushes. A rating of 250 PSI and 180°F is common on the picks here, and it is well above normal residential pressure, which gives you headroom on a hot-water feed. A unit rated for 250 PSI and 250°F is the safer choice if your dishwasher taps a hot line that runs hot.
Decide how many you need
One arrestor handles one supply line. If your dishwasher has both a hot feed and you also hear the toilet or the ice maker thump, a two-pack saves you a second order and a second wait. Single units suit a one-appliance fix; two-packs suit a whole-bathroom or kitchen tidy-up.
Side-by-Side Comparison
| Model | Best For | Connection | Max Pressure / Temp | Pack Size | Amazon |
|---|---|---|---|---|---|
| Sioux Chief 660-TC1 Mini Rester★ Best Overall | Single dishwasher line, in-line PEX | 3/8″ OD compression tee | — | 1 | Amazon |
| TTFLEX 3/8″ Comp ArrestorMost Reviewed | Toilet and dishwasher on one order | 3/8″ male comp x 3/8″ female comp | 250 PSI / 33°F–180°F | 1 | Amazon |
| Lidertik LI-231-2-FMTightest Fit | Tight spaces behind a toilet or stop valve | 3/8″ male comp x 3/8″ female comp | — | 1 | Amazon |
| EFIELD MH-230-2-FM Copper Tee | Hot dishwasher feed that runs very hot | 3/8″ compression x 3/8″ female compression | 250 PSI / 250°F | 1 | Amazon |
| SECKWHALE MH-231 | Two appliances fixed in one sitting | 3/8″ OD comp x 3/8″ female comp | 250 PSI / 180°F | 2 | Amazon |
| Yqimtion MH231-2 | Toilet, sink and faucet lines too | 3/8″ male comp x 3/8″ female comp | 250 PSI / 180°F | 2 | Amazon |
| GUOFIS HAMME013-2 | Corrosion-prone basements and hard water | 3/8″ OD compression tee | 250 PSI / 33°F–180°F | 2 | Amazon |
| EFIELD HAMMER013-2 | Stocking spares for two supply lines | 3/8″ compression x 3/8″ female compression | 250 PSI / 250°F | 2 | Amazon |
Detailed Reviews
1. Sioux Chief Mfg 660-TC1 3/8-Inch OD Compression Mini Rester
Our pick — 4.0+★ from 30+ verified ratings; the strongest balance of quality and price.
A 3/8-inch OD compression tee that splices into PEX and draws the most noise-reduction praise on this list.
This is the arrestor to buy if your dishwasher supply runs through PEX and you want the noise to stop without reworking the plumbing. The 660-TC1 is built as an in-line compression tee, which means it splices directly into the supply tube rather than hanging off a stop valve. Sioux Chief lists it for quick-closing faucets, ice maker lines, lavatory feeds and dishwasher supply tubes — the exact set of jobs that cause the bang in the first place. It is a 3/8-inch outside-diameter fitting, so it mates with standard 3/8-inch supply tube.
What wins people over here is simple: the thing works and it works quietly. Functionality is the praise that comes up most, with noise level close behind — the two things you actually bought it for. Installation gets steady positive word as well, which tracks with the design: you tighten two compression nuts instead of soldering anything. One buyer’s account sums the whole appeal up in a single line: it stopped all water hammer, and in one case the fix took about 5 minutes from box to silence. That is the realistic experience if your threads already match.
The catch is information, not performance. Sioux Chief does not publish a PSI or temperature rating on this listing, so if you have unusually high household pressure or a very hot feed, you are buying on the brand’s reputation rather than a printed number. It is also a single unit, so a two-appliance fix means ordering twice.
Where it earns the top slot
- Splices in-line into PEX, so no extra tee fitting to source
- 3/8-inch OD compression mates with standard supply tube
- Noise reduction is the standout in real-world use, not just on paper
- Compression install — no soldering, no special tools
What to weigh before ordering
- No published PSI or temperature rating on the listing
- Sold as a single unit, so multi-appliance jobs need a second order
- Four-plus decades on the market means old stock can surface — check the seals
Go for it if: your dishwasher feed is 3/8-inch tube and you want the thump gone in one evening.
Pause if: you need a printed pressure rating to feel confident, because this listing does not give you one.
2. TTFLEX Water Hammer Arrestor 3/8″ Comp
The only pick here that names both CUPC/UPC listing and NSF-61 certification, with a 250 PSI rating to back it.
Start with the number that decides most installs: this arrestor carries CUPC/UPC listing and NSF-61 certification, the standards that matter for anything touching drinking water. The body is brass and stainless steel with a stainless exterior finish, and it is explicitly lead-free. The connection is 3/8-inch male compression on one end feeding into 3/8-inch female compression on the other — the standard shape for slipping onto a dishwasher or toilet stop.
Its rated working range is 250 PSI at temperatures from 33°F to 180°F, which covers a normal household feed with room to spare. At 0.17 kg it is a light part that will not strain a flexible supply line. That pressure rating makes it a more conservative buy than the Sioux Chief above, which publishes no rating at all — here you can point to a real ceiling instead of trusting a name. Owners consistently describe easy installation and a clean fit, and the noise story lands too: pipes that used to groan loudly go quiet.
Here is the honest trade-off. The dishwasher line is a hot feed on many installs, and this unit tops out at 180°F. If your hot water runs hotter than that at the tap, step up to a 250°F-rated model instead of pushing this one past its label.
The certification argument: CUPC/UPC and NSF-61 are the two certifications that answer the question “is this safe on a drinking-water line?” — and this is one of the few picks here that names both on the listing.
Reach for this one if: you want paperwork behind the part — certified, lead-free, and rated to a real pressure ceiling.
Look elsewhere if: your dishwasher taps a hot feed above 180°F.
3. Lidertik Hammer Arrestor 3/8 Inch
At 1.6 ounces, the lightest arrestor here — a stainless 304 chamber sized for a cramped cabinet.
Weight is the tell on this one. At 1.6 ounces, the Lidertik is far and away the lightest arrestor here — the SECKWHALE two-pack comes in at 6.24 ounces, so you are hanging roughly a quarter of the mass off your supply line. In a cabinet where the dishwasher hose is already coiled tight against the shutoff, that difference is the whole point. The body is low-lead brass with a stainless steel 304 chamber, and both ends are 3/8-inch compression, male and female, so it fits a standard angle stop.
Buyers praise how it feels and fits. It threads onto 3/8-inch angle stop valves (the shut-off valve under your sink) and 3/8-inch hoses cleanly, and people with copper pipe report it working well. Results are mixed, though: some owners hear the banging stop completely, and some still hear it. The pattern suggests the ones still hearing it face a heavier hammer than one small chamber can absorb. That is not a defect — it is a limit of chamber volume on a larger system.
Treat this as the right pick for a light, occasional thump on a modern appliance, and as a first step rather than a guaranteed cure on a hard-hitting older system. The compact body is a real advantage in a tight cabinet, and the cost of finding out is low.
What the spec sheet gives you
- 1.6 ounces — the lightest unit on this list by a clear margin
- Stainless steel 304 chamber resists wear better than a bare brass pocket
- Low-lead brass body on a drinking-water line
- 3/8-inch male and female compression fits standard angle stops
The realistic ceiling
- Results are split — a small chamber will not swallow a heavy system-wide hammer
- The listing does not publish a PSI or temperature rating
Best matched to: a compact cabinet and a light, quick-closing-appliance thump.
Not the one for: a whole-house hammer that rattles walls, which needs more chamber volume than this offers.
4. EFIELD MH-230-2-FM Water Hammer Arrestor
A copper tee rated to 250 PSI and 250°F, for a dishwasher feed that runs genuinely hot.
Copper and brass construction is the headline, and so is the rating: this EFIELD tee is rated to 250 PSI and a maximum working temperature of 250°F. Compare that to the TTFLEX at 180°F and the difference matters — a dishwasher that pulls straight off a hot line can see water well above what a 180°F part is built for. The connection is 3/8-inch compression on one side and 3/8-inch female compression on the other, described by EFIELD as perfect for dishwasher connection, and it is NSF-61 compliant and lead-free.
The purpose written on the box is exactly your problem: reduce unstable water pressure and noise to protect the dishwasher control system. Owners describe it silencing hammering in showers and sinks, and stopping pipe thumping during ice maker and water dispenser cycles. At 0.24 kg it is heavier than the TTFLEX at 0.17 kg, which is the copper body talking — more mass, and a solid feel in the hand.
Where this one needs an honest caveat is durability over the long haul. Some units keep working great for a long time, and some reportedly quit after a short run. That split is the reason to buy from a listing with a return path rather than a bin at a hardware clearance table.
The case for copper: a 250°F temperature ceiling is the highest on this list, matched only by the EFIELD two-pack further down. On a hot dishwasher feed, that headroom is the spec that matters.
The honest asterisk: reports of early failure exist alongside reports of years of quiet service, so treat the warranty and return window as part of the purchase.
Pick this when: your dishwasher draws from a hot line and you want the most temperature headroom available.
Think twice if: you want a part you can install and forget for a decade without any risk of a dud.
5. SECKWHALE Water Hammer Arrestor 3/8 Inch
A two-pack of C46500 brass tees rated 250 PSI and 180°F — one for the dishwasher, one for the toilet.
The material spec is the interesting part here. SECKWHALE builds the body from C46500 brass, a grade chosen for corrosion and abrasion resistance, and wraps it in stainless steel. The result is rated to 250 PSI and 180°F, meets UPC and NSF requirements, and arrives as a two-pack of 3/8-inch OD compression by 3/8-inch female compression tees. You can install them horizontally or vertically, which matters when the only free space behind the dishwasher is sideways.
The strongest signal from owners is functionality — it simply does the job, and in one case the fix took about 5 minutes. Quality and value both come through positively, with the two-pack angle doing real work: one part for the dishwasher line and a spare for whatever else in the house is banging. At 6.24 ounces each, these are substantial little units rather than hollow shells.
Two honest notes. First, owners disagree on whether it fully kills the hammer — a chamber this size will soften a moderate spike but will not erase a violent one. Second, the fit feedback is the weakest area, so measure your thread before you order rather than assuming every 3/8-inch stop is identical.
What makes it the value leader
- Two arrestors per order — dishwasher plus one more line
- C46500 brass body rated for corrosion and abrasion resistance
- 250 PSI and 180°F working range with UPC and NSF compliance
- Mounts horizontally or vertically to suit the space you have
Before you click buy
- Will not fully erase a heavy, system-wide hammer
- Thread fit is the weakest-reported area — verify your stop valve first
Worth grabbing if: you have two noisy lines and want one shipment to cover both.
Skip past if: your thump is severe enough that you suspect the whole system needs a larger chamber.
6. 3/8″ Comp Water Hammer Arrestor 2 PACK
A two-pack of lead-free brass tees that mount in any orientation with no welding, glue or special tools.
Yqimtion’s pitch is refreshingly direct: bolt it on in any orientation, and you are done. The listing explicitly says no welding, fittings, glue or special tools are required, and it can go horizontally, vertically or any position in between. That is the difference between a weekend plumbing job and a ten-minute one when the space behind the dishwasher is awkward. You get a two-pack of stainless steel tees with 3/8-inch male compression feeding 3/8-inch female compression, and it is listed for dishwasher, sink, toilet and faucet lines.
The safety side is covered too: lead-free brass construction that meets UPC and NSF requirements, rated up to 250 PSI and 180°F. The mechanism is stated plainly — during a toilet cycle the water flow shifts and causes hammer and pressure swings, and the arrestor absorbs them and steadies the pressure. For a dishwasher line the same logic applies the moment that fill valve snaps closed.
With a modest review base, this one is best judged on the spec sheet rather than deep owner testimony, and the spec sheet is genuinely complete. The one gap is that no PSI or temp figure goes above 180°F, so a very hot feed needs a different pick.
Install reality: the “no special tools” line is not marketing fluff here — a compression tee that mounts in any orientation means you can work around a hose that refuses to bend.
Good match for: anyone who wants a two-pack and a tool-free, any-angle install.
Not ideal for: a hot feed that runs above 180°F.
7. 2PACK GUOFIS Tee Water Hammer Arrestor, 3/8″ OD Compression
A two-pack of stainless steel tees rated 250 PSI and 33°F to 180°F, built for corrosion-prone locations.
Corrosion resistance is the reason to look at this pair. The GUOFIS body is stainless steel, called out on the listing as built to resist corrosion while it absorbs water shock and stops banging noise. In a basement or a hard-water house, that is not a minor detail — it is the thing that decides whether the part is still doing its job in a few years. The connection is a 3/8-inch OD compression tee for dishwasher connection with a female compression end, and it is rated to 250 PSI across a 33°F to 180°F range.
Installation is the same straightforward story as the rest of this list: mount it horizontally or vertically in the supply line and tighten the compression nuts. At 12.48 ounces for the two-pack, these are the heaviest per-unit pieces in the group — the stainless shell is carrying real metal. There is no review history to lean on here, so buy this one on the material spec and the two-for-one packaging, not on a track record.
The limit is the temperature ceiling again: 180°F max, so a hot dishwasher feed that runs hotter needs the EFIELD copper tee instead. Otherwise this is a sensible two-pack for a corrosion-prone location.
Why the stainless matters
- Stainless steel body specified for corrosion resistance
- Two arrestors in one order for a two-appliance fix
- 250 PSI ceiling with a 33°F to 180°F working range
- Vertical or horizontal mounting in the supply line
Where it runs out of road
- 180°F ceiling rules out very hot feeds
- No owner history to check against — you are buying on spec alone
Suits you if: you are in a damp basement or a hard-water area and want stainless in the wall.
Look past if: you want proven owner experience before you commit.
8. 2Pcs EFIELD Tee Water Hammer SS Arrestor, 3/8″OD Comp
Two stainless arrestors rated 250 PSI and 250°F — the hottest ceiling here, with a spare for the shelf.
Here is the spec that separates this two-pack from the budget crowd: 250 PSI maximum working pressure and a maximum working temperature of 250°F. Only one other pick on this list, the single EFIELD copper tee, matches that temperature ceiling. So if you want two arrestors and you also want hot-feed headroom, this is the combination that gives you both. The body is stainless steel, safe for potable water, with 3/8-inch compression by 3/8-inch female compression connections described as perfect for faucet and dishwasher connection.
At 0.38 kg for the pair, these have real substance in the hand. Owners describe them as looking like expected quality and going in easily, and the noise picture is the familiar split: some hear the loud banging drop away, some do not get the suppression they hoped for. Read that as a sizing question rather than a defect — a chamber absorbs what it can hold.
One honest catch: these have stainless bodies with a brass exterior finish, not the solid copper of the EFIELD above, and the two cost about the same. So choose by count: two units rated to 250°F (this one) or one copper unit rated to 250°F. Keep a spare on the shelf and you will never make a second trip for a single quiet part.
The 250°F two-pack argument: matching the highest temperature rating on this list while giving you a spare unit is a genuinely useful combination, especially if both your dishwasher and your ice maker bang.
Choose this if: you want a spare on the shelf and the top temperature rating in a two-pack.
Rather not if: you only have one noisy line and one unit would cover it.
Know the Specs
Connection size and type (3/8-inch compression)
The compression fitting is the screw-on nut that seals against the supply tube with a small brass ring. On a dishwasher line, 3/8-inch outside diameter is the common size in the United States, and you will see it written as 3/8″ OD Comp or 3/8″ male and female compression. Male means the threaded end sticks out; female means the threads are inside. A male-to-female tee drops onto an existing angle stop without extra adapters, while an OD compression tee splices into the tube itself. Getting this wrong is the most common reason a new arrestor leaks or will not seat, so check your stop valve before you order.
Working pressure and temperature (PSI and °F)
PSI stands for pounds per square inch, the measure of how hard the water pushes on the inside of the part. A rating of 250 PSI is well above typical household pressure, so it gives you a safety cushion rather than sitting at the edge. The temperature number matters just as much on a dishwasher, because that appliance often taps a hot feed. A 180°F ceiling covers most homes, and a 250°F ceiling gives you room if your water heater runs hot. Always match the rating to the water the line actually carries, not to the number that looks best on the box.
Common Questions
Will a 3/8-inch arrestor fit my dishwasher supply line?
Do I need one arrestor or two for a dishwasher?
Why does my dishwasher bang when it finishes filling?
Is 180°F enough for a dishwasher hot feed?
Do I need to solder anything to install one?
How long does a water hammer arrestor last?
Can a water hammer arrestor go on a toilet or ice maker too?
What is the difference between a copper and a stainless arrestor?
Will one arrestor quiet the whole house?
Does the arrestor need to be mounted a certain way?
The Bottom Line
For most people, the water hammer arrestor for dishwasher that ends the noise with the least fuss is the Sioux Chief 660-TC1. It splices straight into a 3/8-inch supply tube (the thin line feeding your dishwasher), and buyers report the bang simply stops. If you want certification behind the part, the TTFLEX carries CUPC/UPC and NSF-61 certification (independent plumbing and drinking-water safety approvals) with a 250 PSI rating (how much water pressure it can take). And if your dishwasher taps a hot feed, reach for the EFIELD copper tee — its 250°F ceiling (the hottest water it is rated for) is the highest on this list alongside the EFIELD two-pack, and that headroom is exactly what a hot line needs.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.




