What Is a Water Hammer Arrestor and How Does It Work? | Stop The Bang

A water hammer arrestor is a sealed device that absorbs the pressure surge when a valve shuts off water suddenly, stopping the bang and protecting your pipes.

That thud after the dishwasher finishes—or the rattle when the washing machine fills—comes from moving water slamming to a stop. A quick-closing valve kills the flow in a fraction of a second, and the energy travels back through the piping as a pressure wave. An arrestor gives that wave a cushion to push against instead of your pipes, fittings, and appliance valves.

How Does a Water Hammer Arrestor Actually Work?

Inside a code-compliant arrestor sits a permanently sealed pocket of air or gas, separated from the water by a piston, bellows, or similar barrier. When the valve closes and the pressure wave arrives, that trapped gas compresses, absorbing the water’s kinetic energy before the surge can rattle the rest of the system.

That sealed cushion separates a real arrestor from the old-school open air chamber—a capped pipe stub. An air chamber works the same way at first, but water gradually absorbs the trapped air and the chamber waterlogs, losing its dampening effect. Devices certified to ASSE 1010 use a permanently sealed cushion so protection doesn’t fade with time.

What Do Plumbing Codes Require?

The International Plumbing Code requires water hammer arrestors wherever quick-closing valves are used, installed per the manufacturer’s instructions and conforming to ASSE 1010. Section 604.9 of the 2018, 2021, and 2024 IPC editions carries this requirement, and the 2024 definition describes the device’s job as absorbing the pressure surge when flow stops suddenly.

Two more standards shape what you buy:

  • ASSE 1010 covers the sealed-cushion device and its pressure rating.
  • PDI-WH201 sets performance testing, certification, and sizing categories—seven in total, covering normal building-water-system sizes. Certified products may carry the PDI mark.

Local rules can differ. Your state or municipal code may adopt a different IPC edition or amend it, and that version controls the job.

Where Should It Be Installed?

Place the arrestor as close as possible to the valve that closes suddenly—distance is the enemy of effectiveness. Zurn’s engineering guide puts it plainly: the closer to the point of closure, the better, and that matters most at the far end of a long pipe run.

For a branch line no longer than 20 feet, Zurn identifies the preferred spot as the end of the branch, between the last two fixtures. Run longer than 20 feet and the Zurn Z1700 document calls for two arrestors with combined capacity meeting the calculated need—one between the last and next-to-last fixtures, another roughly midway. If you’re adding one under a kitchen sink to quiet a dishwasher valve, our tested water hammer arrestor picks for dishwashers cover sizing and fit for that setup.

Sizing is where most DIY installs go wrong. Don’t pick by pipe diameter alone. Add up the fixture units on the hot or cold branch, find that total on the manufacturer’s selection table, round any half fixture unit up, and step to the next larger unit when line pressure runs above 65 psig. Orientation matters too: Zurn’s instructions call for SHOKTROL units upright on a horizontal run, and model-specific instructions always win.

Common Mistakes And Pressure Limits

Most failures trace back to placement, sizing, or ignored pressure ratings. A unit mounted far from the closing valve does little; one undersized by pipe diameter alone can’t absorb the surge it was bought for. High system pressure can also put a device outside its rating—

Zurn Z1700 Limit Rating What It Means For You
Maximum working pressure 125 psi Above this, the unit is out of spec
Maximum static pressure 250 psi Ceiling for non-flowing pressure
Maximum temperature 300°F Fine for standard domestic hot water
Upstream PRV threshold Above 60 psi Add a pressure-reducing valve first
Typical applications Solenoid, flush, pump valves Sinks, lavatories, dishwashers, washers

Two more traps: treating a waterlogged air chamber as an equivalent fix (it isn’t), and ignoring flow velocity. The IPC separately requires velocity control because fast-moving water can hammer even with an arrestor in place. For anything affecting public health and safety, a trained plumbing professional is the right call—but understanding the device means you can ask the right questions.

Common Questions

Can I install one myself?

A confident DIYer can add an arrestor at an accessible fixture valve, such as under a sink or behind a washing machine—shutting off water, cutting or teeing into the line, and sealing connections. If the device sits inside a wall, in a tight crawlspace, or the sizing math is unclear, hire a licensed plumber—a leak behind drywall costs far more than the install.

How long do these devices last?

A sealed-cushion arrestor has no air to lose the way an open chamber does, so it keeps working for years without maintenance—the point of the ASSE 1010 design. Failure usually comes from corrosion, a burst barrier, or pressure beyond the unit’s rating, not normal wear.

Will it quiet every banging pipe?

Not always. An arrestor handles the surge from a quick-closing valve, the most common cause of a single sharp bang. If the noise is a continuous rattle, a squeal, or tied to high flow velocity, the cause is different and may need a pressure check or a plumber’s diagnosis.

Sources

Scroll to Top