A water heater timer is an electrical time switch that powers an electric storage water heater on and off on a set schedule, cutting electricity use during peak-rate hours.
Your water heater may be the biggest electricity drain in the house, running around the clock whether anyone needs hot water or not. A timer cuts power during hours you choose — usually when rates peak or the house is empty — and restores it before you shower. Intermatic, which makes most models sold in the US, describes it as a time switch wired into the heater’s power circuit to control power to a compatible heater.
What a Water Heater Timer Actually Controls
The timer controls electricity, not water temperature. It sits between the breaker and the heater and decides when the heater gets power. When on, power reaches the thermostat and elements and the heater works as usual, cycling to its set temperature. When off, the heater cannot heat, but hot water in the tank stays hot for hours — that stored heat is the basis of the savings.
Two hardware families do this job. Mechanical units use a clock motor and physical trippers. Electronic units use a digital clock, programmed events, and relays, usually with battery or supercapacitor backup so the schedule survives an outage.
Mechanical and Digital Models Compared
Mechanical timers are cheap and simple; digital timers cost more but schedule to the minute and hold settings through power loss. Both are sold for 240-volt electric heaters.
The Intermatic WH21 is the classic mechanical unit: 208–250 VAC, 25-amp resistive rating, two sets of ON/OFF trippers, up to 12 events each way, and a 30-minute minimum switching interval. The WH40 and T104-20 are similar, but their minimum ON/OFF time is a full hour.
Digital models offer far more control. The EH40 has seven-day scheduling, 42 events per week, one-minute minimum switching, and AA-battery backup. The WH2725AT ships pre-programmed, handles 19 ON and 19 OFF events, adjusts for daylight saving automatically, and has a 100-hour supercapacitor backup plus a NEMA 3R outdoor enclosure.
No reliable current retail prices are published on the manufacturer’s pages, so check a retailer. Sizing matters more: the timer’s voltage and ampere rating must meet or exceed your heater’s actual load.
How To Set One Up Without Cold Showers
Setup starts with matching the timer to the heater, then programming ON periods long enough to recover before anyone needs hot water.
- Confirm the timer is rated for your heater’s voltage, current, switching type, and wire size. A 208–250 VAC model is not suitable for a 120-volt heater.
- Shut off the circuit at the breaker and verify no voltage with a tester.
- Mount the timer per instructions and local code; connect line and load conductors to the labeled terminals.
- Set the current time, including AM/PM and daylight saving where supported.
- Program the ON windows, starting conservative — aggressive shutoffs leave the tank short.
- Restore power and check the override button and status indicator. On the EH10, an LED load indicator confirms the timer is passing power.
- Watch actual demand for a week, then tighten the schedule around your utility’s off-peak rates.
Most people run one long overnight window plus a shorter morning window. If showers run cold, widen the first window before touching the thermostat.
Compatibility Rules and Common Mistakes
These timers are built for electric storage water heaters only. Intermatic lists “Electric Water Heater” as the application for the WH21, and nothing supports use with gas, tankless, heat-pump, or boiler systems.
- Mismatching voltage. A 240-volt-only model cannot be assumed to work on a 120-volt circuit.
- Undersizing the ampere rating or choosing the wrong switching configuration, such as SPST where DPST is needed.
- Assuming a weatherproof enclosure makes any location safe. Outdoor installs still need code-compliant conduit, fittings, grounding, and weather protection.
- Programming the heater off longer than the tank can hold usable heat.
Installation puts you in contact with potentially lethal line voltage. Use a licensed electrician where local rules require it, and control the breaker throughout. To match a model to your tank, start with our tested water heater timer roundup.
The manufacturer’s overview of water heater control solutions lists the full model range and rated specs.
Common Questions
Will a timer lower my electric bill?
Only with time-of-use rates or a heater that runs while the house is empty. The timer shifts consumption to cheaper hours and cuts standby losses during long empty stretches. On a flat rate with heavy use, savings are usually modest — it cannot make a heater more efficient.
Will hot water still be there when the timer is off?
Yes. Insulation slows heat loss, so the tank holds hot water for hours. How long depends on tank size, insulation, starting temperature, and draw. Most households get usable hot water through an overnight or workday off window.
Does this work with a gas or tankless heater?
No. Intermatic specifies these for electric storage heaters. Gas units use a burner and flue, and tankless units heat on demand, so cutting power saves no energy and may disable controls. Match the device to your heater type before buying.
Sources
- Intermatic. “Water Heater Control Solutions” Model range, ratings, and how timers control electric heaters.
- Intermatic. “WH21 Water Heater Timer” Mechanical timer specs and electric water heater application.
- Intermatic. “WHAVQ4 Water Heater Timer” Analog timer ratings, enclosure, and backup details.