How to Set Up and Align a Table Saw for Accurate Cuts

A table saw cuts square only when the blade runs parallel to the miter slot — fence and riving knife adjustments come after that one check.

The blade is almost always the reason — not the wood, not the technique. DeWalt’s manual for the DWE7491RS walks through how to set up and align a table saw for accurate cuts in a fixed sequence, and that sequence is the part most owners skip.

Four checks carry the job: a support that does not move, a blade square to the table and parallel to the miter slot, a fence that locks in line, and a riving knife standing vertical.

Mount The Saw Before You Touch A Wrench

A table saw that rocks or creeps on its support loses alignment no matter how precisely you adjust it. DeWalt’s DWE7491RS instruction manual calls for a stand, bench, or other rigid support that keeps the saw from moving or tipping, on a level, well-lit surface.

Power comes off next. The manual requires switching off and unplugging before you pull the throat insert, change a blade, or touch the riving knife, anti-kickback pawls, or blade guard. Nobody should be reaching past a live blade with a hex wrench in hand.

Fastener locations, adjustment hardware, and torque values differ from model to model, so the DeWalt DWE7491RS instruction manual is the only spec sheet that matches that particular saw.

How Do You Know The Blade Is Parallel To The Miter Slot?

Mark one tooth, raise the blade, and compare that tooth against a fixed point at the front of the miter slot; then turn the blade by hand until the same marked tooth reaches the rear and compare again. A gap that changes from front to rear means the blade is not tracking the slot.

Power stays disconnected for this. When the gap moves, the correction on the DWE7491RS sits at the rear pivot bracket: loosen the bracket fasteners with a hex wrench just enough to let the bracket shift side to side, work it until the blade runs parallel to the miter-gauge track, then tighten to 110–120 in-lb (12.5–13.6 N·m). Re-measure at the marked tooth — matching gaps front and rear is what tells you the adjustment took.

The rip fence follows the blade, never the other way around. Unlock the rail, set the blade at 0° bevel, slide the fence until it touches the blade, and lock it. A fence that clamps solid and holds the line is set; one that shifts when you bump it needs the lock checked before anything gets cut.

A rip that comes out narrower at the tail, or burn along one edge, sends you back to the same two checks — blade to slot first, then fence.

Table Saw Setup And Alignment: The Order That Holds Square

Setup and alignment hold when the checks run in one direction: support, blade, fence, then riving knife and guards.

Check What To Set Sign It’s Done
Support Rigid stand or bench, level, well lit Saw stays put when you push a board through
Power Unplugged before any adjustment Cord out of the outlet, switch off
Bevel and height 0° for square cuts, about 1/8 in above the stock Bevel gauge on zero, teeth clear the wood
Blade to miter slot Parallel, measured at one marked tooth Same gap at front and rear
Pivot bracket 110–120 in-lb (12.5–13.6 N·m) Wrench stops at the setting, blade still reads parallel
Rip fence In line with blade and slot, locked No drift when you nudge it sideways
Riving knife Vertical, in line with the blade Square sits flush along the knife face
Guard and pawls Installed, clearing the blade Guard tracks through full height and bevel travel

With the blade raised fully at 0°, lay a square flat against the riving knife — vertical and in line with the blade is the target, and the set screws on the knife handle small errors. Repeat the check after adjusting. A knife standing out of line with the blade is a kickback risk, not a cosmetic flaw.

Guards go back on before the next cut. After a kickback, DeWalt’s manual wants the saw shut off and the riving knife, anti-kickback assembly, and blade guard inspected before work resumes, with the workpiece kept against the fence or miter gauge.

Our tested wood working table saw roundup covers models with rack-and-pinion fences and cast tops that keep their settings.

Get the order right once and the saw holds. Get it wrong and you will be re-cutting the same board twice.

Common Questions

Can You Align A Table Saw Without A Dial Indicator?

Yes. The manual’s own method uses one marked tooth and a fixed reference at the front and rear of the miter slot, with the blade turned by hand and the saw unplugged. A dial indicator reads the error faster and in finer numbers, but the front-to-rear comparison catches any misalignment that shows up as a tapered cut.

Should The Rip Fence Sit Exactly Parallel To The Blade?

Most manuals call for the fence to lock in line with the blade and miter slot, and that is where to start. Plenty of woodworkers open the rear of the fence a few thousandths of an inch to reduce binding on long rips. Check your model’s manual first — some locking designs do not tolerate the offset.

How Often Does A Table Saw Need To Be Rechecked?

There is no service interval that fits every saw. Recheck after moving the machine, after a kickback, after a blade swap if the arbor or throat insert came off, and any time rip cuts start showing a taper or burn along one edge. A portable saw on a jobsite stand moves more than a cabinet saw bolted to a floor.

Sources

Scroll to Top