The mill frame must match your bar’s cutting capacity and your saw’s displacement —
Choosing the right chainsaw mill comes down to three numbers — your widest log, your saw’s engine size, and your bar’s usable length — plus bar and chain details that decide whether the setup works at all.
What Size Mill Does Your Widest Log Require?
Pick the smallest mill whose stated cutting width exceeds your target board width, because frame length and cutting width differ. A 30-inch Alaskan MK IV cuts boards up to 26 inches wide; a 36-inch model tops out at 32 inches. Measure your largest log, add a couple of inches of margin, and stop there.
Bigger frames weigh more, cost more, need a stronger powerhead, and are awkward to haul into the woods. Going oversized “just in case” usually means a mill that sits in the garage.
Which Chainsaw Displacement And Bar Type Does Each Mill Require?
Every mill has a minimum engine displacement, and a long bar is not proof your saw can pull it. Granberg’s requirements climb steeply with frame size. Bar construction matters too: the Small Log Mill G777 explicitly will not work with laminated bars and needs solid steel. Larger MK IV configurations assume a single-ended bar unless the saw carries 120 cc or more for a double-ended setup.
Chain specs round out the match. The 60-inch C2 package, for example, specifies a.404 sprocket, a.063-inch gauge, and a 194-link chain. Confirm pitch, gauge, sprocket, and link count before you buy; a mill that clamps on fine but runs the wrong chain cuts poorly and wears fast.
| Granberg Model | Saw And Bar Requirement | Max Cut Width / Price |
|---|---|---|
| G777 Small Log Mill | 16–20-inch solid-steel bar; 50–70 cc saw | Up to 18 inches; price not listed |
| G778-30 MK IV | Bar 30 inches or less; 60 cc or more | Up to 26 inches; $323 |
| G778-36 MK IV | Bar 36 inches or less; 70 cc or more | Up to 32 inches; price not listed |
| G778-48 MK IV | Single bar to 48 in; 90 cc or more | Up to 44 inches; $379 |
| G778-56 MK IV | Single bar to 56 in; double bar to 66 in at 120 cc | Up to 52 inches; $365 |
| G778-60 MK IV | Single bar to 60 in; double bar to 72 in at 120 cc | Up to 54 inches; $446 |
| G778-72 MK IV | Single bar to 72 in; double bar to 84 in at 120 cc | Up to 68 inches; $524 |
| G778-84 MK IV | Single bar to 84 in; double bar to 96 in at 120 cc | Roughly 70–78 inches; $575 |
| G778-60C2 package | 120 cc or larger;.404 sprocket,.063 gauge, 194 links | 60-inch mill; $1,835 |
Granberg’s official Alaskan mill lineup lists current pricing and full specs. To compare assembled, tested setups before committing, this roundup of wood mill chainsaw picks worth owning covers complete rigs side by side.
What Else Goes Into The Total Cost And Setup?
The mill is only part of the spend. Budget for a ripping chain, sharpening gear, an oiler or lubrication setup, and a rigid, level first-cut platform. Granberg identifies ripping chain and first-cut platforms as the pieces that produce good results, and its C2 package pairs slabbing rail brackets with customer-supplied 2×4s to build that platform.
- Assemble and clamp per the included instructions, then check every fastener and bar clamp for tightness.
- Set the cut depth for your first board and keep the chain sharp and well oiled.
Milling loads a saw hard and continuously. Use the specified ripping chain, inspect clamps and fasteners often, and wear proper chainsaw protective gear — take the PPE checklist from your chainsaw maker or OSHA/ANSI guidance, since the mill pages do not provide one. For the widest, highest-power frames, confirm your saw’s oiler keeps up; a helper oiler solves most of it.
Common Questions
Can I use a laminated bar with the Granberg Small Log Mill?
No. Granberg states the G777 requires a solid-steel bar and will not work with laminated bars. If your saw came with a laminated bar, factor a solid-steel replacement into your budget.
Is a longer mill always the better choice?
No. A longer mill adds weight, cost, and power demand, and can be awkward to transport. Choose the smallest configuration that safely covers your actual logs, then step up only when a bigger frame earns its keep.
How much does a ripping chain add to the setup cost?
Prices vary by length and spec, so check the current listing for your bar and gauge. Granberg names ripping chain as one of the two pieces — with a first-cut platform — that produce optimal results, so treat it as required, not optional.
Sources
- Granberg. “Alaskan Mill” Lists current MK IV frame sizes, prices, bar and saw requirements, and cut widths.
- Granberg. “G777 Alaskan Small Log Mill” Documents the 16–20-inch bar, 50–70 cc saw requirement, and solid-steel bar only restriction.
- Granberg. “G778-56 Alaskan MK IV Chain Saw Mill” Specifies single- and double-ended bar limits and the 120 cc requirement.