Rotary Tool Bits and Attachments Explained | Match Bits To Material

Rotary tool bits do the cutting, grinding, and polishing, while attachments control depth, reach, and angle — and the right pairing depends on your material, shank size, and max RPM.

Bits and attachments are the interchangeable parts that turn a rotary tool into a router, a sharpener, or a precision drill, and matching each one to the material and the tool’s speed range is what keeps the workpiece intact and your hands safe. The sections below sort the accessory families, the shank and collet sizes that hold them, and the attachments that change how the tool behaves.

What Do The Main Accessory Types Actually Do?

Dremel groups rotary accessories into cutting, grinding, carving, sanding, brushing, polishing, and drilling — and each family has a job it does better than the rest. Pick the family first, then the specific bit.

  • Cutting wheels: thin abrasive or fiberglass-reinforced wheels slice metal, plastic, wood, and drywall. Dremel’s 710-08 kit includes EZ456 and EZ476 1-1/2-inch fiberglass-reinforced wheels.
  • Grinding stones: aluminum-oxide stones handle ferrous metals; silicon-carbide stones take on stone, glass, and ceramics. The 710-08 kit carries 932 and 952 aluminum-oxide stones plus 84922 silicon-carbide stones.
  • Carving and engraving: high-speed cutters remove wood, plastic, and soft metal. Dremel’s 115HP Max Life cutter has a titanium-nitride coating, a 1.5-inch overall length, and a 1/8-inch shank, sold two to a pack.
  • Sanding: drums and bands shape surfaces; discs finish them. The 710-08 kit spans 60- through 240-grit.
  • Brushes and polishing: carbon-steel brushes strip rust, nylon brushes clean gently, and felt wheels with compound bring up shine.
  • Drill bits: small bits handle light precision drilling — kit 733-01 includes the model 150 1/8-inch bit.

Shanks, Collets, And Mandrels: What Holds The Bit?

A collet grips the accessory shank, and the collet size must match that shank or the bit will wobble or slip. Dremel lists four collet sizes — 0.8, 1.6, 2.4, and 3.2 mm — and tightening the collet nut both centers and grips the accessory.

Some accessories have no built-in shank, which is where mandrels come in. Model 401 uses a small screw to hold sanding discs and felt wheels; model 402 is the screw mandrel for thin cut-off wheels. EZ Lock is Dremel’s quick-change system for compatible cutting wheels, sanding discs, and polishing pads.

How Fast Should You Run Each Bit?

Speed follows the material and the accessory, and the accessory’s published maximum RPM is a ceiling, not a target. Low RPM suits polishing, plastic, and soft wood; too much speed burns the workpiece.

Material Recommended RPM (115HP bit)
Wood 20,000–30,000
Soft metal 15,000–25,000
Hard metal 15,000–20,000
Plastic 15,000–20,000
Soft stone or shell 20,000–30,000
Kit 733-01 / 726-01 max 35,000

For controlled cuts and clean edges, the attachment matters as much as the bit. Dremel’s plunge-router attachment (model 335-01) adds depth adjustment for inlays and edging, while the drywall/wood cutting guide gives a stable base and depth control. If you are weighing which machine to pair with these accessories, this roundup of tested woodworking rotary tools covers the models worth buying.

Which Attachments Change How The Tool Handles?

Attachments extend reach, relieve hand fatigue, or add routing and sharpening capability the bare tool lacks. The multi-vise (2500-01) holds the project or the tool at different angles, and a circle cutter makes adjustable circles in drywall, wood, or laminate. A sharpening set adds guides for lawnmower blades, chainsaw blades, scissors, and garden shears.

Before any bit goes in, check three things: shank size against the collet, the accessory’s max RPM against your setting, and whether the material calls for an abrasive or a cutter. Dremel’s guide to rotary tool accessories spells out the collet and speed pairings for each family.

Common Questions

Can I Use One Bit For Both Wood And Metal?

A cutter can often handle soft metal after wood, but a grinding stone rated for ferrous metal will clog or glaze on plastic and wood. Match the abrasive to the material, and use the recommended RPM range for the harder of the two.

What Happens If The Collet Size Is Wrong?

A mismatched collet either won’t grip the shank or won’t let it seat, and the bit vibrates or slips under load. Confirm the shank size against Dremel’s four collet sizes — 0.8, 1.6, 2.4, and 3.2 mm — before tightening.

Do I Need A Mandrel For Every Accessory?

No. Mandrels are only for accessories without an integrated shank, like sanding discs and thin cut-off wheels. Bits with a built-in 1/8-inch shank go straight into the collet.

Sources

Scroll to Top