What Safety Shoe Standards and Certifications Mean (EN ISO 20345)?

EN ISO 20345 is the European product standard for safety footwear with protective toe caps; US workplaces reference ASTM F2413 instead.

The marking line printed inside the tongue is the part product photos never show. It is a base class code plus optional symbols for the hazards the shoe survived in testing. Miss it and a pair that feels armored can still fail the job you bought it for.

What Does EN ISO 20345 Actually Certify?

EN ISO 20345 sets minimum requirements and test methods for safety footwear with protective toe caps, covering mechanical, slip, thermal, and ergonomic risks. It is a European standard, not a US certification, and says nothing about appearance.

The current edition is ISO 20345:2021, published December 17, 2021, replacing ISO 20345:2011. An amendment, ISO 20345:2021/Amd 1:2024, arrived in 2024, so the edition year matters when comparing stock.

Class I covers leather and other materials, excluding all-rubber and all-polymeric builds. Class II is entirely molded rubber or polymeric footwear. The 2021 edition also defines a hybrid category between the two.

The standard does not cover high-visibility properties. Visibility depends on clothing, dirt, mud, and light in the work area, so a hi-vis claim is separate from toe-cap compliance.

Safety Shoe Standards And Certifications: What Decides The Outcome

The printed code decides it, not the toe-cap material. Steel, composite, or aluminum describes the cap; the class marking describes what the whole shoe was tested to do.

SB is the floor: basic safety-footwear requirements, including a protective toe cap. Every higher class adds tested properties on top of SB.

Marking What It Adds Watch For
SB Basic safety footwear with a protective toe cap No slip or sole-puncture claim attached
S1 Closed energy-absorbing heel area, antistatic behavior, fuel-oil resistance Still no water or sole-puncture protection
S2 S1 properties plus resistance to water penetration and upper absorption A water-resistant upper is not waterproof footwear
S3 S2 plus sole penetration resistance and a cleated outsole Says nothing about electrical, heat, or chemical hazards
S4 Class II molded footwear with SB-level protection and S1-type properties Rubber and polymeric builds only
S5 S4 plus sole penetration resistance and a cleated outsole Same electrical and chemical limits as S3

Slip resistance changed in the 2021 edition: the old SRA, SRB, and SRC markings were replaced by SR and Ø, so 2011-edition shoes can carry labels not found on current stock.

Anything past the class code — electrical resistance, heat resistance, metal-free construction, chain-saw protection — must be specifically marked and verified. The manufacturer’s declaration controls, not the shelf tag. Match the model name and exact version on that paperwork to the shoe in your hand before you pay.

If you are comparing pairs now, our tested picks for safety work shoes spell out the marking each model carries, so you can match code to hazard instead of guessing from photos.

Do EN ISO 20345 And ASTM F2413 Mean The Same Thing?

No. They are separate regional standards with separate marking systems, and a shoe certified to one is not automatically certified to the other.

The US reference is ASTM F2413; the current protective-toe specification is ASTM F2413-24, published in 2024. It covers impact and compression resistance and can add optional properties such as metatarsal protection, conductive footwear, electrical-hazard resistance, static dissipation, puncture resistance, chain-saw cut resistance, and dielectric insulation.

OSHA’s foot-protection rule, 29 CFR 1910.136, recognizes footwear built to the incorporated ASTM F2412-2005 test methods and ASTM F2413-2005 performance specification, older ANSI Z41 editions, or footwear shown to be at least equally effective. It applies where workers face falling or rolling objects, objects piercing the sole, or electrical hazards that remain after other controls.

ASTM F2413-24 warns that aftermarket footbeds or inserts, or resoling, can break compliance and invalidate the ASTM marking. European-certified footwear carries the same caution, since structural changes put the conformity claim in question.

Before you buy:

  1. Assess the hazard first. Falling objects, sole puncture, electrical exposure, heat, and slip risk each point toward different markings.
  2. Identify the governing market. Europe means the EN ISO 20345 marking plus conformity paperwork; the United States means the ASTM marking.
  3. Read the whole marking, including the edition year and every optional symbol.
  4. Check fit and condition. A compliant toe cap guarantees nothing about comfort, ankle support, or chemical compatibility.

Common Questions

Is EN ISO 20345 Accepted In The United States?

It is not a US certification, and no federal rule requires it. OSHA’s foot-protection rule points employers to ASTM F2412 and ASTM F2413, older ANSI Z41 editions, or footwear shown to be at least equally effective. A European-marked shoe can qualify under that equal-effectiveness clause, but the employer must document why it does.

What Protection Does An S3 Rating Actually Confirm?

S3 starts with SB-level toe-cap protection, then adds S1 features (closed energy-absorbing heel, antistatic behavior, fuel-oil resistance), S2 water-penetration and upper-absorption resistance, and sole penetration resistance with a cleated outsole. It does not confirm electrical-hazard, heat, chemical, or chain-saw protection — those need their own markings.

Can I Add Insoles To Certified Safety Shoes?

Ask the manufacturer first. ASTM F2413-24 warns that aftermarket footbeds or inserts, and resoling, can cause footwear to fail the standard and void the ASTM marking. The same caution applies to European-certified pairs. Insoles sold as compatible with that exact model are the lower-risk pick.

Sources

Scroll to Top