Jaw width alone won’t tell you if a vise fits your bench or your stock — matching jaw opening, throat depth, and bench thickness decides it.
For the full breakdown, see our best Woodworking Workbench Vise guide.
A vise that clamps a board halfway and stops is worse than no vise at all. The single most common buying mistake is ordering by nominal jaw size — “I want a 7-inch” — and discovering the opening capacity, throat depth, or bench-thickness limit doesn’t match the work actually planned. Size a workbench vise by four numbers together, and the right model picks itself.
Yost Vises’ current woodworking catalog makes a clean working example, because it spans sizes and duty levels with published specs. Here’s what each number actually controls.
What Do The Four Vise Measurements Actually Control?
Jaw width sets how wide a board the jaws grip; jaw opening sets how thick a board slides between them; throat depth sets how far a vertical piece can drop below the jaw line; and mounting depth sets which benches the vise can bolt to. Those are four separate limits, and the smallest one wins.
- Jaw width — the nominal size printed on the box. It limits board width, but it does not predict opening.
- Jaw opening — the maximum gap between jaws. This is the spec that actually decides whether your stock fits.
- Throat depth — how much material can hang below the jaws. Matters for dovetailing, edge work, and tall boards.
- Bench thickness — the maximum bench the vise’s mounting hardware can clamp through.
The 7-inch models in Yost’s line prove the point: the M7WW opens 8 inches with a 3-inch throat, while the heavier 7WW-CA opens 9 inches with a 4-inch throat. Same nominal size, different real capacity.
Which Vise Size Fits Your Bench And Work?
Match the size to the bench and the work, not to a number you saw in a shop tour. A 6.5-inch vise suits small projects and tight benches; 7-inch models cover general furniture work; 9–10-inch vises handle big panels and heavy use, but demand a stout bench.
Yost’s catalog splits the line roughly along those lines.
If comparing the full field side by side helps before deciding, this tested roundup of woodworking vise picks lays the options out with specs and pricing in one place.
| Model And Size | Key Capacity Specs | List Price |
|---|---|---|
| L65WW Hobby, 6.5 in | 4.5 in opening; benches to 2.25 in | $39.99 |
| F9WW Front Vise, 9 in | Cabinetmaker’s front vise | $58.99 |
| F10WW Front Vise, 10 in | Cabinetmaker’s front vise | $89.99 |
| M7WW Rapid Action, 7 in | 8 in opening; 3 in throat; 30,000-PSI cast iron | $109.99 |
| M9WW Rapid Action, 9 in | Rapid-action lever; T-bar handle | $135.99 |
| M10WW Rapid Action, 10 in | Medium-duty rapid action | $166.99 |
| 7WW-CA Ductile, 7 in | 9 in opening; 4 in throat; benches to 2.25 in | $163.99 |
| 10WW-CA Ductile, 10 in | Benches to 3 in; GGG-V-445 Type I Class II | $220.99 |
How Do You Verify Fit Before Buying?
Measure the bench, compare that number against the vise’s stated maximum bench thickness, then check opening and throat against your largest planned workpiece. Every step is a tape measure and a spec sheet.
- Measure bench thickness at the exact mounting spot, not the average.
- Compare it to the vise’s listed limit — exceeding it prevents secure clamping. The L65WW and 7WW-CA cap at 2.25 inches; the 10WW-CA allows 3 inches.
- Check the maximum jaw opening against your thickest stock.
- Check throat depth if you hold tall boards or work near an edge.
- Reinforce the bench underside and use every specified mounting point and its hardware.
- Position the fixed jaw flush with, or slightly above, the benchtop, with the screw turning freely.
Clamp finished surfaces against wood facings or protective liners rather than bare metal jaws. Tighten only enough to hold the work — excess force damages wood, hardware, and the vise. And don’t assume a woodworking vise swaps for a metalworking bench vise; jaw geometry, facings, and load ratings differ. Confirm current Yost specifications on the woodworking vise collection page before ordering, since listed prices shift with sales, shipping, and regional availability.
Common Questions
Is a bigger vise always better?
No. A large vise adds mass and capacity, but it also needs a thicker, stiffer bench and eats more benchtop space. A 10-inch model on a thin bench can flex or tear out its mounting. Choose the smallest vise whose opening, throat, and bench limits clear your biggest planned workpiece.
Why does jaw width not match jaw opening?
Jaw width is the length of the jaw face; opening is how far the sliding jaw travels. Design and screw length set the second number independently. Yost’s 7-inch M7WW opens 8 inches while the 7-inch 7WW-CA opens 9 inches, so the nominal size never predicts capacity alone.
What is throat depth for?
Throat depth is the vertical clearance below the jaw line. It lets tall boards hang down while you work their top edge — useful for dovetailing and edge planing. Shallow throats force awkward repositioning on vertical work.
Sources
- Yost Vises. “Woodworking Vises” Source for all model specs, bench-thickness limits, and listed prices cited above.