An Xbox One X (model 1787) hides its 1 TB drive under two plastic cases, and a new drive still needs Xbox system software before the console boots.
For the full breakdown, see our best Xbox One X HDD Replacement guide.
A dead 1 TB drive turns an Xbox One X into an expensive doorstop. The repair is a dozen Torx screws; the obstacle is what follows, when the console powers on to a blank screen because the new drive carries no Xbox software. This walkthrough covers how to replace the hard drive in an Xbox One X, model 1787, from the rear sticker to the first successful boot.
Every Xbox One X left the factory with a 1 TB 2.5-inch hard-disk drive. The parts exist and the procedure is documented, so a careful owner can finish it in one sitting — provided you don’t assume any 2.5-inch drive will do.
Xbox One X HDD Replacement: Parts That Actually Fit
That description is the whole compatibility story.
A generic 2.5-inch SATA drive is not plug-and-play here. The plastic bracket and the Xbox-specific connector arrangement have to move across, and the drive needs Xbox system files before the console treats it as storage. No documented maximum capacity exists, and no internal SSD upgrade is officially supported. This is also a different job from plugging an external USB drive into a rear port, which adds storage without opening anything.
Comparing drives before you spend anything makes sense — our tested Xbox One X HDD replacement picks separate what fits model 1787 from what just looks close.
| Stage | Fasteners | What To Watch |
|---|---|---|
| Rear case | 2 × T10 Torx, ~12.6 mm | Hidden under the right-side rear sticker |
| Lower plastic case | None | Hinged ZIF flap on the front ribbon cable |
| Lower metal case | 2 × T10 Torx | Disc drive can lift with the case |
| Drive to upper case | 4 × T10 Torx, ~11.4 mm | Console has to be flipped over |
| Drive bracket | 4 × T10 Torx, ~8.6 mm | Move the Xbox-specific connector across |
Opening An Xbox One X Without Breaking It
The console comes apart in four stages — rear case, lower plastic case, lower metal case, then the drive and its bracket — and every fastener is T10 Torx. iFixit’s Xbox One X hard drive replacement guide is written specifically for model 1787, and the sequence below follows it.
- Unplug every cable, power down, and work on a stable surface. Ground yourself before touching anything inside.
- Peel back the sticker on the right-side rear corner and remove the two T10 screws underneath, about 12.6 mm long.
- Slide the upper plastic case forward until its clips let go, then lift it clear.
- Flip up the hinged ZIF locking flap on the front ribbon cable, then lift off the lower plastic case.
- Remove the two T10 screws holding the lower metal case and lift it away, keeping a hand on the disc drive, which can come up with it.
- Turn the console over and take out the four T10 screws, roughly 11.4 mm long, pinning the drive to the upper metal case.
- Move the disc drive only as far as the job needs, and never pull or sharply bend its cables.
- Pull the hard-drive bundled cable and SATA cable straight upward by their connectors, not by the wires.
- Lift the drive out by its sides, remove the four roughly 8.6 mm T10 bracket screws, and move the bracket plus the Xbox-specific connector to the new drive.
- Reconnect the drive connector, SATA cable, and bundled cable, then reassemble in reverse.
Will The Console Boot After A Drive Swap?
A newly installed drive often refuses to boot on the first try, because it has to be prepared with Xbox system software before the console treats it as its own. iFixit’s guide warns that physical replacement alone may not make the console operational and that additional software tools may be needed.
That warning leaves a gap worth naming. The available documentation does not establish a current Microsoft-supported preparation method, a verified recovery-package version, or a supported-format list. Check Microsoft’s current support pages for console recovery media before you begin, and download anything you need while the old drive can still be read.
Locally stored games, captures, and profiles live on the drive itself, so a failed drive usually takes them with it. Saves that synced to your Xbox account may return when you sign back in, but confirm that with Microsoft rather than assuming it.
Check the warranty position before the screwdriver comes out. Opening the console can damage clips, cables, or components and may affect warranty or service eligibility, so read Microsoft’s current warranty statement first.
Line up three things before you start: a confirmed model 1787 replacement that includes the bracket, a T10 Torx driver, and a plan for the software step. With those in hand this is a screwdriver job. Without them it turns into a refurbished-console purchase.
Common Questions
Can A Standard 2.5-Inch Laptop Drive Work In An Xbox One X?
It can fit and connect, but it is not drop-in. The console expects Xbox system files on the drive, and the plastic bracket plus the Xbox-specific connector have to transfer from the old unit. iFixit’s pre-formatted assembly exists because a bare drive still needs that preparation before the console will use it.
What Happens To My Saved Games During The Swap?
Files stored only on the internal drive stay there, so a dead drive usually means those are gone. Games and saves that synchronized to your Xbox account may download again once you sign in. Confirm that behavior with Microsoft support before you count on it, and back up what you can while the old drive still reads.
Is Swapping The Drive Cheaper Than Replacing The Console?
Cheaper, usually, though not simpler. That money is only well spent if you can also finish the software step, since a swapped drive with no Xbox system files leaves a console that powers on and goes nowhere.
Sources
- iFixit. “Xbox One X Hard Drive Replacement” Step-by-step teardown labeled for model 1787, including screw lengths and cable handling.
- iFixit. “Xbox One X HDD and Bracket” Replacement assembly listed at $59.99, pre-formatted for Xbox One X only.
- iFixit. “Xbox One X Repair” Device overview confirming model details and available repair documentation.