A YT7B-BS replacement must match 150 × 65 × 93 mm, the same terminal layout, and at least 120 cold-cranking amps.
A battery can match the label exactly and still refuse to drop into the box. Case height, terminal corners, and hold-down clearance cause nearly all of that frustration, and none of it shows up in a seller’s fitment chart.
The three figures that settle the physical side — 150 mm long, 65 mm wide, 93 mm tall — are what any yt7b-bs battery cross reference and compatibility guide is really pointing at, and they outrank the model name on the sticker.
What follows is the verified Yuasa spec sheet, the codes sellers cross it to, and the checks worth running before you hand over money for a near-miss.
What Does A YT7B-BS Battery Cross Reference To?
The direct cross reference is the YT7B-BS designation itself. Aftermarket sellers also list equivalents as ST7B-BS or Parts Unlimited 2113-0218, and those codes are handy in a search box — they are not proof that a battery fits.
Yuasa builds the YT7B-BS as a 12-volt sealed AGM in its Fresh Pack, maintenance-free family, with cast lead-calcium plates and a listed weight of 5.9 lb. Yuasa’s figures put it at 6.5 Ah at the 10-hour rate, 6.8 Ah at the 20-hour rate, and a recommended charge current of 0.7 A.
| Yuasa Model | Size (L × W × H) | Capacity / CCA |
|---|---|---|
| YT7B-BS | 150 × 65 × 93 mm | 6.5–6.8 Ah / 120 CCA |
| YT9B-BS | 150 × 69 × 105 mm | 8.0–8.4 Ah / 120 CCA |
| YT12A-BS | 150 × 87 × 105 mm | 10–10.5 Ah / 175 CCA |
| YT12B-BS | 150 × 69 × 130 mm | 10–10.5 Ah / 210 CCA |
| YTX7A-BS | 150 × 87 × 93 mm | 6–6.3 Ah / 105 CCA |
| YTX7L-BS | 113 × 70 × 130 mm | 6–6.3 Ah / 100 CCA |
Rating standards explain the odd spread you’ll see in listings. Yuasa’s YT7B-BS product listing rates it at 120 cold-cranking amps, while a Yuasa technical data sheet published for the UK market states 110 A at −18°C.
YT7B-BS Compatibility: What Decides Whether It Fits
Dimensions and terminal layout decide fit; displacement and cranking amps decide whether the bike starts happily afterward.
Work through these checks in this order:
- Case size inside 150 × 65 × 93 mm, with a millimeter or two of slack for the hold-down.
- Terminal posts in the same corners, positive and negative the same way round.
- Cable reach with the battery seated on the tray, not held above it.
- Cranking amps at or above 120 CCA.
- An AGM-compatible charger waiting on the bench.
One mismatch catches people late: the hold-down tab. A battery 12 mm taller can sit on the tray and still foul the seat pan or the tool kit, and a case 4 mm wider can bind against a frame rail. Test-fit the dry battery before you fill or charge anything, because returns get harder once acid goes in.
Vehicle-specific fitment has to come from the owner’s manual or an official application guide. Aftermarket listings market this battery for Suzuki DR-Z400 E/S/SM models from 2000 to 2017 and BRP DS450 models from 2008 to 2015, but a listing is a claim about a range of vehicles, not a promise about your trim or your market.
Lithium is the other trap. A pack advertised as a YT7B-BS replacement is not chemically interchangeable — lithium needs a charger built for it, its own battery-management electronics, and usually the manufacturer’s sign-off before a swap.
A straight swap is simpler: match the three dimensions, match the terminal corners, hit 120 CCA or better. Our tested YT7B-BS battery roundup covers the sealed AGM options that measure out correctly.
Charging And Installing A Fresh Pack Without Damage
A Fresh Pack YT7B-BS may ship dry and need acid filling, sealing, and an initial charge before it holds anything. Yuasa’s regional listings put the acid fill at roughly 0.30–0.33 L. Some aftermarket equivalents arrive sealed and pre-charged, so read the box before assuming.
Charge with an AGM-compatible motorcycle charger at about 0.7 A for this battery. Never install an unactivated fresh-pack battery and hope the bike’s charging system finishes the job.
AGM batteries are sealed and spill-resistant, not inert. Keep sparks and flames clear, wear eye and hand protection, avoid bridging the terminals with a wrench, and take the old battery to an authorized US collection point for recycling.
Before the cables come off, run this order:
- Confirm the vehicle’s specified battery in the owner’s manual.
- Measure the old case against 150 × 65 × 93 mm.
- Match terminal corners and polarity to the original.
- Check for 120 CCA or higher on the new label.
- Activate or charge per the battery’s own instructions first.
- Negative cable off first; going back on, positive first and negative last.
Common Questions
Can I Use A YT9B-BS Instead?
No on most bikes. The YT9B-BS measures 150 × 69 × 105 mm, so it is 4 mm wider and 12 mm taller than the YT7B-BS, and it carries the same 120 CCA despite the bigger case. It may fit a bay designed for it, but the extra height usually fouls the seat pan or the hold-down bracket.
Do I Need A Special Charger For An AGM Motorcycle Battery?
Yes — use a charger with an AGM or sealed-lead setting. Yuasa specifies roughly 0.7 A for the YT7B-BS, and a charger pushing too much current can cook a small 6.5 Ah battery. A smart charger with an AGM mode and an output of 1 A or lower covers it; a car-style fast charger is the wrong tool.
What Happens If I Install A Battery With Reversed Polarity?
Best case, nothing powers up. Worst case, reverse current runs through the rectifier, regulator, and ECU, and the repair bill dwarfs the battery. Compare the positive and negative terminal corners against the old battery before the cables go on, and stop if the layout is mirrored rather than treat it as a labeling error.
Sources
- Yuasa Battery USA. “YT7B-BS” Source for the 12 V AGM construction, 6.5 Ah/6.8 Ah capacity, 120 CCA, dimensions, weight, and 0.7 A charge current.
- Yuasa UK. “YT7B-BS Technical Data Sheet” Lists the alternative 110 A rating at −18°C that explains regional CCA differences.
- Taiwan Yuasa. “Motorcycle Batteries” Source for the electrolyte volume and acid-included weight figures.