An XLR lavalier needs a condenser capsule, the right adapter for your recorder, and phantom power support; comparing sensitivity, self-noise, and maximum SPL matters more than the label on the box.
A “professional lavalier” doesn’t automatically mean an XLR plug on the end of the cable. Plenty of high-end lavs ship with MicroDot, mini-jack, or mini-XLR connectors for wireless bodypacks, and only reach a mixer’s XLR input through a dedicated adapter. Get that adapter wrong and the microphone either won’t power up or will hum through every take. The specs below are what separate a lav that works on a real set from one that fights you.
Does An XLR Lavalier Always Have An XLR Connector?
No. Several respected lavaliers use proprietary or bodypack connectors, and you add the XLR output through an adapter. The DPA 4060 is sold in MicroLock, TA4F mini-XLR, three-pin LEMO, and mini-jack versions; the DAD9001 adapter converts MicroLock to a standard three-pin XLR. The AKG C417 PP uses a standard XLR connector, while the C417 L uses a professional three-pin mini-XLR for AKG wireless transmitters. The Sennheiser ME 2-II is a mini-jack lav built for evolution Wireless SK bodypacks.
That split matters at the buying stage. If you plan to plug into a recorder, mixer, or camera with a true XLR input, confirm the exact connector variant and whether the adapter is included. A mini-jack lav connected straight to a mixer’s XLR input is not equivalent to a balanced XLR run.
Which Specs Actually Change How The Mic Sounds?
Polar pattern, frequency response, and self-noise shape the recording far more than marketing language does. All three models above are omnidirectional pre-polarized condensers with a 20 Hz–20 kHz frequency response, so their real differences hide in the sensitivity and noise figures.
- Sensitivity: DPA 4060 lists 20 mV/Pa (−34 dB re 1 V/Pa, ±3 dB at 1 kHz); AKG C417 states 7 mV/Pa. Lower sensitivity means more preamp gain, which can raise the noise floor.
- Self-noise: DPA 4060 is typically 23 dB(A), max 26 dB(A); the AKG C417 lists 34 dB-A; the Sennheiser ME 2-II page states 36 dB. Quieter is better for soft-spoken dialogue and quiet rooms.
- Maximum SPL: DPA 4060 handles 134 dB peak at 10% THD — useful if you’re miking a loud source.
- Dynamic range and impedance: DPA 4060 is typically 106 dB dynamic range with 30–40 ohm output; AKG C417 is 200 ohms with a recommended 1,000 ohm load.
- Weight and size: DPA 4060 is 7.5 g with cable and connector, 5.4 mm diameter, 12.7 mm capsule length, 1.8 m cable; AKG C417 is 68 g, 15 mm tall, 7.5 mm diameter, 1.5 m cable; Sennheiser ME 2-US is 6.5 mm diameter with a 1.6 m cable.
Power, Adapters, And Compatibility Checks Before You Buy
A condenser lav needs the right bias voltage, and the adapter decides whether your gear can supply it. The DPA 4060 runs on 5–10 V through a DPA adapter for wireless systems; with the DAD6001-BC XLR adapter, P48 phantom power is specified, and the mic will operate from 12 V. Current draw is typically 1.5 mA, or 3.5 mA with the DAD9001-BC XLR adapter.
The AKG C417 mini-XLR version is listed at 2–12 V — check the exact PP documentation before assuming a phantom voltage or adapter wiring. Balanced XLR adapters are designed for balanced microphone inputs; mini-jack bodypack connections are not automatically interchangeable. Match sensitivity to your gain staging too: a very sensitive lav can overload a bodypack or input on a loud source.
Mounting is half the result. Clip the capsule near the chest or upper sternum, keep it clear of fabric, and use the manufacturer’s windscreen where available. Clothing rub is a mechanical problem no spec sheet predicts — but it will ruin a take faster than any noise figure. When you’re ready to compare specific models side by side, the tested XLR lavalier microphone roundup pairs real-world notes with the spec sheets.
| Spec | DPA 4060 | AKG C417 PP |
|---|---|---|
| Connector / adapter | MicroLock, TA4F, LEMO, mini-jack; DAD9001 to XLR | Standard XLR (PP); mini-XLR (L) |
| Power | 5–10 V via DPA adapter; P48 with DAD6001-BC | 2–12 V listed for mini-XLR (verify PP) |
| Sensitivity | 20 mV/Pa (−34 dB, ±3 dB) | 7 mV/Pa |
| Self-noise | 23 dB(A) typical, 26 dB(A) max | 34 dB-A |
| Max SPL | 134 dB peak (10% THD) | Not stated |
| Impedance | 30–40 ohms | 200 ohms (1,000 ohm load) |
| Weight / size | 7.5 g; 5.4 mm dia.; 1.8 m cable | 68 g; 7.5 mm dia.; 1.5 m cable |
Availability And Warranty Notes
Some models simply aren’t orderable new. Sennheiser’s US page marks the ME 2-II as no longer available to purchase, which makes it a used-market or spare-parts search rather than a new purchase. DPA and AKG each publish their own warranty terms by region, so confirm coverage for your country before relying on the box copy — and confirm regional availability, since connector variants and supplied adapters can differ by market and kit. None of the official product pages listed here showed a current US price, so any figure you see elsewhere deserves a fresh check at the retailer.
A final word on the DPA 4060’s environmental limits: −40 °C to 45 °C (−40 °F to 113 °F) and up to 90% relative humidity.
Common Questions
Can I plug a mini-jack lavalier into an XLR input with a simple cable?
A passive mini-jack-to-XLR cable will not provide the bias voltage a condenser lav needs, and it usually creates an unbalanced connection that is not equivalent to a balanced XLR input. Use a manufacturer adapter designed for that specific microphone, such as DPA’s DAD9001 for MicroLock models, and confirm the required voltage first.
Is a lower self-noise rating always better for a lavalier?
Lower self-noise means less electronic hiss when the preamp gain is high, which helps on quiet dialogue. The DPA 4060 lists 23 dB(A) typical against 34 dB-A for the AKG C417 and 36 dB for the Sennheiser ME 2-II. On loud sources, maximum SPL and gain staging matter just as much.
Why do the same lavaliers come in so many connector variants?
Lavaliers are often sold to fit specific wireless systems, and each brand uses its own bodypack connector. DPA lists MicroLock, TA4F mini-XLR, three-pin LEMO, and mini-jack variants of the 4060. Buy the variant that matches your transmitter, or budget for the adapter that converts it to XLR.
Sources
- DPA Microphones. “4060 Lavalier Microphone Kit — Product Manual.” Supports the 4060 specifications, adapter options, and connector variants.
- Sennheiser. “ME 2-II — Product Page.” Supports ME 2-II specs, compatibility, and discontinued status.
- AKG. “C417 Series — Product Page.” Supports C417 PP and C417 L specifications and connector differences.