Worx Battery Charger Compatibility Guide: Which Batteries Fit Which Chargers | One Charger, Most Packs

Worx PowerShare and PowerShare PRO 20V batteries all charge on the same 20V MAX chargers, so a PRO pack never needs a special charger.

Two packs that look different on the shelf, a sticker that says PRO, and a charger in the garage that may or may not be the right one — that mismatch is the usual reason a battery sits at zero. The short answer for the Worx PowerShare line is that the charger side is almost never the problem. The tool side is where people get burned, and one wrong pairing there can cost you a battery or a tool.

Below you’ll find the charger models Worx lists, what each one does to charge time, and the voltage rules that decide whether a pack works in your tool at all.

Do PowerShare PRO Batteries Need A Different Charger?

No. Worx states that PowerShare PRO batteries charge on all existing Worx 20V MAX chargers, including the WA3742, WA3764, WA3770, WA3881, WA3884, and WA3835 models. The PRO label changes the cell quality and capacity, not the charging interface.

The WA3881 20V 2A quick charger covers the full spread: 1.5Ah, 2.0Ah, 4.0Ah, 5.0Ah, 6.0Ah, and 8.0Ah packs, with listed battery model numbers running from WA3520 and WA3525 through WA3575, WA3578, WA3512, WA3512.1, WA3522, WA3544, and WA3671.

One distinction matters here. Charger compatibility and tool compatibility are separate questions. A charger that happily tops up an 8.0Ah pack says nothing about whether that pack will run a given saw. Worx makes this explicit: batteries should be used with tools of the corresponding voltage.

How Long Does Each Battery Take To Charge?

Charge time scales with capacity, and Worx’s own figures put a 2.0Ah pack at about an hour on the WA3881 and a 4.0Ah pack at roughly two hours on the same charger. The 6A rapid charger cuts that down considerably, though the listing Worx publishes for it is a European one.

Here is how the packs and chargers line up, using the specifications Worx publishes on its US product pages.

Battery / Charger What Worx Lists Approximate Charge Time
WA3881 20V 2A Quick Charger All PowerShare and PRO packs, 1.5Ah–8.0Ah 1 hr for 2.0Ah; 2 hr for 4.0Ah
WA3867 6A Rapid Charger All 20V PowerShare batteries (European listing) 25 min for 2.0Ah; 45 min for 4.0Ah; 70 min for 6.0Ah
WA3742 / WA3764 / WA3770 / WA3884 / WA3835 PowerShare PRO packs confirmed Varies by output; check the label
WA3575 20V 2.0Ah Battery Two units combine for 40V equipment About 1 hr on WA3881
WA3669 20V 2.0Ah Battery Sold in kit with WA3881; works in 40V and 80V setups Full charge in 1 hr
WA3674 20V 4.0Ah PRO Battery Fits 20V, 40V, and 80V PowerShare tools; charger not included About 2 hr on WA3881
WA3678 20V 8.0Ah PRO Battery Fits 20V and 40V, plus designated 80V products; charger not included Longest of the range

The two PRO bare packs, WA3674 and WA3678, are worth flagging: Worx says plainly on both product pages that the charger is not included. If you own no 20V MAX charger yet, the combo kits bundle one, and a standalone charger is the cheaper add-on. Our tested Worx battery charger roundup covers which output suits a garage full of packs.

Which Voltage Setup Does Your Tool Actually Need?

A single 20V pack runs 20V tools. Two 20V packs run compatible 40V tools. Designated 80V equipment takes its own battery count, and Worx says to follow that specific tool’s installation instructions rather than improvising a combination.

This is the rule people break. The 40V platform is built around two matched 20V packs working together, which is why a WA3575 or WA3669 pairs up cleanly while a single pack in the same slot does nothing.

Confirm three things before you charge anything: the battery carries the PowerShare or PowerShare PRO marking, the charger is a listed Worx 20V MAX model, and the tool’s required voltage matches your pack count.

Common Questions

Can I Charge A Worx 20V Battery On A 40V Charger?

Worx does not list cross-voltage charging as supported. Its 20V MAX chargers, such as the WA3881, are the documented match for 20V PowerShare and PowerShare PRO packs. Use the charger rated for the battery’s own platform, and check that both pieces carry the matching PowerShare marking before you connect them.

Is The WA3867 Rapid Charger Available In The US?

The published specifications for the WA3867 6A charger come from Worx’s European site, which lists it as compatible with all 20V PowerShare batteries. US buyers should verify local electrical ratings, model availability, warranty coverage, and price on the US site before ordering, since the European listing may not match the US version.

Why Does My 4.0Ah Battery Take Two Hours To Charge?

Because capacity drives charge time on a fixed-output charger. Worx rates the WA3881 at roughly one hour for a 2.0Ah pack and about two hours for a 4.0Ah pack. An 8.0Ah battery on the same charger will take longer still. A higher-output charger shortens the wait, but the manufacturer times are approximations.

Sources

Scroll to Top