Woods Finish Mower Parts Diagram | Start At The ID Plate

Order Woods mower parts by matching your machine’s ID plate model and serial number to the part number in that model’s illustrated breakdown.

Two blades can carry the same 21-inch length, the same 2.5-inch width, and two different part numbers, because one is built for a center deck and the other for a wing. Reading a Woods finish mower parts diagram correctly starts with the machine, not the component: the identification plate names the exact model, and the model decides which illustrated breakdown applies.

Woods builds eight current finish mowers across two families, and parts rarely cross between them. Knowing which family your machine belongs to turns a plate reading into a part number.

Which Number On The ID Plate Decides The Part?

The model designation does — TK60.20, TK72.20, TKP72.40, TKP84.40, TBW12.20, TBW12.40, TBW15.40, or TBW17.40 — and the serial number pins down the revision built behind it. Write down both, along with deck configuration and any date or revision marking, before you open any manual.

The prefix tells you more than the width. TK models are TurfKeeper finish mowers; TBW models are Turf Batwing mowers with three decks instead of one. Within each family, the middle number separates standard machines from professional ones, and that gap is where most wrong orders begin. A standard TurfKeeper runs a cast-iron spindle housing with lubed-for-life bearings; a professional TKP model runs ductile-iron housings with triple greasable ball bearings. Those housings can look interchangeable on a bench and still not bolt up.

Warranty tables follow the same split. A standard model covers the mower for one year residential or 90 days commercial, the spindle for one year, and the gearbox and seals for six years. Professional TKP and TBW models run three years on spindles, ten on gearboxes, and two on structure, with up to ten years including parts, labor, and seals on applicable models.

Woods Finish Mower Parts Diagram: Where The Part Numbers Live

Each model has its own product page with a Download User Manual link, and the illustrated parts breakdown inside that manual is the only place a part number should come from. The Woods finish mower model pages list all eight machines, so you can open the exact one your plate names.

From there:

1. Open the product page for your model, not the general finish-mower category.
2. Download the manual, then find the assembly you need: deck, spindle, blade, belt, sheave, caster, hitch, gearbox, hydraulic cylinder, shielding, or hardware.
3. Copy both the item number off the drawing and the Woods part number beside it. The item number shows where the part sits; the part number tells the dealer what to pull.

Deck position matters on batwing models. The belt shield on a TKP84.40 lifts off without tools, which puts the sheaves, belt, and spring-loaded idler in reach for a check against the drawing.

Belt and sheave orders go the same way. Belt length, section, and idler hardware are matched to the deck, so a belt that measures close is not the same belt.

What To Confirm Before You Pay

Confirm tier, deck position, and assembly spec against the serial number, then order through a Woods dealer or authorized parts channel. Parts that look alike can differ in hole pattern, shaft dimensions, belt length, bearing arrangement, blade rotation, or deck position — none of which a photo shows. Ordering by appearance, deck width, or blade length is how the wrong part gets shipped twice.

If you’d rather line up specific components before calling a dealer, this tested roundup of Woods finish mower parts puts the common replacements side by side.

1. Record the complete model suffix and serial number.
2. Note the tier: standard lubed-for-life spindle or professional greasable ductile-iron spindle.
3. Mark center versus wing deck on any blade, spindle, or belt order.
4. Check the machine requirements those parts serve.
5. Match the complete assembly spec for belts, blades, bearings, and sheaves — belt section and caster type included, whether solid rubber or the 15 × 6-6 and 18 × 9.5-8 pneumatics.
6. Read the number back to the dealer with the model and serial attached.

Woods directs operators to run and service every machine according to its supplied operator’s manual, and that manual carries the diagram a part number has to come from.