What Size Washer and Dryer Risers Do You Need? | Match The Model

Washer and dryer risers typically measure 10 to 15.5 inches tall, 27 to 28 inches wide, and 26 to 29 inches deep, but the right size is the one listed as compatible with your exact appliance model.

The dimensions themselves are easy. The hard part is that laundry pedestals aren’t universal, and a model number match matters more than any tape measurement.

Here’s what the numbers look like in practice, how to check fit before you order, and the sizing mistakes that cost people a second shopping trip.

How Tall Can A Washer Pedestal Be?

That range matters because it’s roughly counter height to shoulder height for an average adult. A 10-inch pedestal keeps the door opening in a comfortable bend-and-reach zone. A 15.5-inch pedestal gets the drum closer to waist level, which is easier on your back but eats more vertical room.

Whirlpool’s representative model, the WFP2715HW, is a 15.5-inch pedestal with storage for front-load pairs.

What Size Washer And Dryer Risers Fit Your Machines?

Pedestals are matched to specific models, not to a size category. Compatibility depends on brand, appliance dimensions, base geometry, attachment points, and sometimes the model year, so a pedestal built for one generation won’t necessarily bolt to the next.

Whirlpool also notes that some Whirlpool and Maytag pedestals cross over between the two brands because the dimensions and designs are similar, but that isn’t a blanket guarantee. Verify by model number every time. Compact washers and dryers may need compact-specific pedestals, and full-size dimensions shouldn’t be assumed to carry over.

Top-load machines are the other exception. Whirlpool states that pedestals aren’t recommended for top-load washers, since the design assumes a front-load base.

If you’re comparing storage styles and drawer layouts, our roundup of tested washer and dryer risers covers how the popular models actually hold up in daily use.

Specification Typical Measurement What It Affects
Pedestal height 10–16 inches (10 and 15.5 common) Reach comfort and total stack height
Pedestal width 27–28 inches Matching the appliance footprint
Pedestal depth 26–29 inches Drawer clearance and rear hose room
Washer/dryer height About 39 inches Combined height with the riser
Combined height Roughly 49–55 inches Overhead cabinet and shelf clearance
Side clearance About 1 inch per side Ventilation and access
Rear clearance About 6 inches Hoses, drain, dryer vent connection
Pedestal weight Roughly 46–51 pounds Installation effort and floor load

How Do You Check Fit Before Buying A Riser?

Pull the model numbers off both appliances first, then confirm the pedestal is listed as compatible with each one. Whirlpool’s support guidance comes down to comparing dimensions, checking the attachment hardware, and verifying the pedestal model against the manufacturer’s documentation rather than relying on physical fit alone.

  1. Record the complete model numbers of the washer and dryer.
  2. Confirm the pedestal’s compatibility list includes both models.
  3. Measure appliance width, depth, base dimensions, and the open floor area.
  4. Add the pedestal height to the appliance height, then check overhead cabinets, shelving, doors, and ceiling clearance.
  5. Keep about 1 inch on each side and 6 inches behind the appliances for ventilation and hose connections.
  6. Verify the mounting brackets and supplied hardware match the appliance base.
  7. Install and level both pieces following the manual for that specific pedestal.
  8. Open the drawer and confirm it clears walls, trim, and the neighboring appliance.

When the pedestal is seated and leveled properly, the appliance sits flush on the platform with no rocking, and the storage drawer slides out freely.

Which Riser Mistakes Cause The Most Trouble?

The most common mistake is buying a “universal” riser without confirming compatibility. A close second is assuming an older pedestal will carry over to a newer appliance, since attachment points and base dimensions can shift between model years.

  • Pairing a washer and dryer pedestal of two different heights, which leaves the set visibly uneven.
  • Ignoring the added 10 to 16 inches and blocking a cabinet or shelf in the process.
  • Skipping rear service space, which makes hose and vent work miserable later.
  • Mounting a pedestal under a top-load washer.

The fix is unglamorous: match the model, measure twice, and confirm the manual before the delivery truck arrives.

Common Questions

Can A Dryer Go On The Same Pedestal As The Washer?

Yes, but only if the pedestal is listed as compatible with both specific models. Whirlpool notes a pedestal may support both a washer and dryer, and the exact model numbers still need checking against the manufacturer’s compatibility information. Never assume a side-by-side pair shares the same base without verifying.

Do Risers Need Extra Room Behind The Appliances?

That space covers the water lines, drain, and dryer vent, and it’s usually the clearance people forget when planning. Leave it even if the riser itself fits the footprint.

Will A 10-Inch Or 15.5-Inch Pedestal Feel Different?

It changes your reach by about 5 inches. The 10-inch version keeps the door lower, which suits shorter users or a low ceiling; the 15.5-inch version lifts the drum toward waist level for less bending. Check overhead clearance first, since the taller option can block a shelf.

Sources

Scroll to Top