A water heater connection kit packages the flexible hot- and cold-water connectors and fittings that tie a storage heater’s ports to your home’s plumbing.
Pulling a heater out of a tight closet with rigid copper ends in a wrestling match. A connection kit replaces that hard-piped run with short flexible connectors that bend around obstructions — and the kit you buy has to match your heater, your pipe material, and your local code. Get the match wrong and you are making a second trip with the water already shut off.
The section below breaks down what actually sits in the box, then the fit rules that decide whether a given kit works on your unit.
What Comes In A Water Heater Connection Kit?
A water-only kit generally holds two flexible connectors, two adapters, and a disconnect clip, with a shutoff valve or sealing tape added in some models. Gas-heater kits swap in a listed flexible gas connector alongside the water parts.
- One hot-water connector and one cold-water connector — Eastman’s electric installation kit lists two 18-inch flexible supply connectors with the box.
- Two compression or threaded adapters — the thread type follows your pipe system, not the heater.
- An integrated cold-side ball valve on many push-to-connect models, so you can isolate the heater without touching the main.
- A disconnect clip — SharkBite’s Max kit includes a U712 clip for releasing the push fitting.
- Sealing tape in some installation kits, like the roll Eastman bundles.
- A flexible gas connector (gas kits only) — a 24-inch gas line appears in Eastman’s gas kit, and it is not interchangeable with a water connector.
SharkBite’s Max kit shows how specific these parts get: it ships two 18-inch, 3/4-inch FIP × 3/4-inch corrugated connectors (models URSS3088FX18 and URSS3088FX18BV), one with a built-in ball valve.
Water Heater Connection Kit Sizes And Compatibility: What Decides The Fit?
Connection size, pipe material, and local code decide whether a kit works — and 3/4-inch is the usual water heater inlet and outlet size in the products documented here.
Check your heater’s nipple size before buying. Then match the other end to what is already in the wall. The cited push-to-connect kits list copper, PEX, CPVC, and PE-RT as compatible pipe, and one page rates its connectors to 200 psi working pressure and 250°F while noting IAPMO listing to ASSE 1061/NSF 61. A gas connector must be approved and rated for gas service on its own.
For gas units, A. O. Smith’s installation guidance calls for 3/4-inch NPT threaded adapters on the hot and cold lines and heat-trap fittings where code requires them. Our tested roundup of water heater connection kits lines up the current options by size and pipe type if you would rather compare than decode specs.
How Do You Install A Water Heater Connection Kit?
The documented sequence runs from shutting off utilities to a leak check, and the connector nut is hand-threaded before any wrenching.
- Shut off the heater’s gas and/or power, then close the water at the appliance valves or the main.
- Inspect the heater nipples for burrs and sharp edges, and clean copper surfaces on sweat connections.
- Hand-thread the connector nut onto the nipple until the seal seats.
- Align and bend the connector without stretching, kinking, or twisting it.
- Restore water and check every joint for leaks.
A threaded joint that weeps gets one more quarter turn. If it keeps leaking, shut the water off, disconnect, clean, and reinstall; a soldered leak means repeating the soldering. The install is done when every joint stays dry through a full pressure check.
Step fidelity note: exact torque figures and adapter types vary by brand, so follow the instructions printed with your kit and the heater maker’s guide. SharkBite documents its push-to-connect procedure on its Max push water heater connection kit page, and Eastman’s electric water heater installation kit page lists the box contents.
Which Kit Fits Your Heater?
Match the kit to the appliance type first, then to the pipe in the wall. Electric heaters need water connectors and adapters only; gas heaters need those plus a listed gas connector. A kit built for rigid copper will not clamp onto PEX without the right push or compression fitting. Skipping the size check is the most common reason a kit gets returned.
Common Questions
Can I reuse the old connectors when replacing a heater?
Often no. Corrugated connectors that have been bent, kinked, or sitting for years may not reseat cleanly, and manufacturers generally call for new connectors on a new install. Check the old connector’s condition and the new heater’s instructions before deciding to reuse anything.
Do I need a shutoff valve in the kit?
Not always, but it helps. An integrated cold-side ball valve lets you isolate the heater for future service without shutting the whole house down. If your kit lacks one, confirm the existing appliance valve works before you start.
Is a gas connector the same as a water connector?
No. Gas connectors are rated and listed for gas service; water connectors are not. Never swap one for the other, and install the gas line per the connector manufacturer’s instructions and A. O. Smith’s guidance for your heater model.
Sources
- SharkBite. “Max Push Water Heater Connection Kit” Documents connector models, sizes, and included disconnect clip.
- Eastman. “Electric Water Heater Installation Kit” Lists water and gas kit contents.
- A. O. Smith. “How Do I Install A Gas Water Heater?” Installation guidance for gas units and adapter sizing.