A triangle screwdriver bit (TA bit) fits three-sided security screws that block Phillips, slotted, and hex drivers, locking down safety covers on electronics, appliances, and toys.
A triangle-drive screw looks like a manufacturing mistake until you try everything in your toolbox and nothing bites. The recess is a small three-pointed triangle, and it exists on purpose: it keeps casual hands out of enclosures the maker never intended you to open. Knowing which bit matches which recess saves the screw from being rounded out by a Phillips that almost fits.
Below is what the bit is, the sizes that actually exist, how to seat one without damage, and where the job stops being a screwdriver problem and becomes a safety problem.
What Is A Triangle Screwdriver Bit?
A triangle bit has a three-sided, three-pointed tip that seats into a matching triangular recess on a security screw. McMaster-Carr describes these as “unique three-point bits” for triangle-drive screws, commonly used to fasten safety covers on electronics.
The bits are ordinary tool steel with a standard shank. McMaster’s triangle power bits run 2 inches overall with a 1/4-inch quick-change hex shank, which locks directly into power tools and hand drivers that accept 1/4-inch hex bits.
Sizes are labeled TA, followed by a number tied to the triangle’s measured length. McMaster lists TA18 at 0.07 inch, TA20 at 0.083 inch, TA23 at 0.09 inch, and TA27 at 0.1 inch. Metric-labeled sets use the same idea in millimeters.
What Are Triangle Bits Used For?
Triangle-drive screws show up wherever a maker wants a fastener that resists casual tampering — the fastener is a mild deterrent, not a lock. Common homes for them include safety covers and enclosures on electronics, appliances, toys, and HVAC equipment.
The tamper resistance is the whole point. A homeowner with a Phillips set cannot get in, so the cover stays on unless someone deliberately buys the matching bit. That is also why the bits are sold in sets rather than singly — you rarely know the size until you look.
For a reader who has already checked the recess and wants a specific pick rather than a whole set, the tested triangle bit roundup covers individual options with real fit notes.
What Size Triangle Bit Do You Need?
The tip size and the shank size are two separate measurements, and confusing them is the most common buying error. A bit can wear a 1/4-inch hex shank and still carry a TA18, TA20, or 2.3-mm triangle tip — the shank tells you what tool it fits, the TA number tells you what screw it fits.
Match the tip to the recess by seating it dry, before you turn anything. The bit should drop fully into the triangle without rocking or sitting proud. Sizes across the common range:
| Size Label | Triangle Length | Typical Source |
|---|---|---|
| TA14 | Small end of the range | TEKTON DZZ92002 set |
| TA18 | 0.07 inch | McMaster, TEKTON set |
| TA20 | 0.083 inch (part 5941A12) | McMaster, TEKTON set |
| TA23 | 0.09 inch | McMaster, TEKTON set |
| TA27 | 0.1 inch | McMaster, TEKTON set |
| 1.8–3.0 mm | Five metric diameters | Five-piece S2 steel set |
| TA30 | Largest in the 10-piece set | Triangle-Bit-Set-10Pack |
One caution on the labels: the cited product pages do not establish a single industry-wide numbering standard, so TA sizes from two different makers may not measure identically. Check the manufacturer’s own measurements before trusting a number.
Steel quality matters less than fit, but it still matters. Both are retailer listings, so treat the prices as snapshots rather than market rates.
How Do You Use One Without Stripping The Screw?
Steady pressure and low speed get the screw out; force and impact drivers get it rounded. Seat the bit fully, keep the driver aligned with the screw axis, and turn slowly with moderate downward pressure.
A short sequence that avoids most damage:
- Confirm the recess is a true triangle, not a tri-wing. Tri-wing screws have three wings radiating from a center and take a completely different bit — a triangle bit will not work.
- Test-fit the bit dry. If it rocks or will not bottom out, go up or down one size rather than forcing a near-fit.
- Lock the 1/4-inch hex shank into a hand driver, bit holder, drill, or power screwdriver that accepts 1/4-inch hex bits.
- Turn at low speed with steady pressure. On small screws, a manual driver gives better feel than a drill.
Stop the moment the bit slips. Reusing a Phillips or flathead because it seems to catch is what rounds the recess and turns a two-minute job into a drill-out.
A magnetic tip helps hold the screw but is not a guarantee — stainless, dirty, and damaged screws often will not hold. McMaster also notes its steel bits suit dry environments, since moisture causes rust.
One boundary worth stating plainly: a triangle bit removes fasteners. It does not make an enclosure electrically safe. Unplug or disconnect power before opening electronics, appliances, toys, or HVAC equipment, follow the manufacturer’s service instructions, and know that opening a product can expose electrical, mechanical, thermal, or stored-energy hazards and may void the warranty.
Common Questions
Is a triangle bit the same as a tri-wing bit?
No. A triangle bit has a three-pointed tip that seats into a triangular recess, while a tri-wing bit has three wings radiating from a center and fits a different screw head entirely. The two are not interchangeable, and forcing one into the other’s recess usually damages the screw.
Can I use a Phillips bit on a triangle screw?
You should not. A Phillips tip may seem to catch on the triangle’s corners, but it does not seat properly and tends to round out the recess under load. Once the triangle is stripped, removing the screw usually requires drilling, so use the correct TA size from the start.
Will a 1/4-inch hex triangle bit fit my drill?
Yes, if your drill or bit holder accepts standard 1/4-inch hex shanks, which most quick-change chucks and multi-bit drivers do. Remember that the 1/4-inch figure describes the shank only — the triangle tip itself may be a TA18, TA20, or another size entirely.
Sources
- McMaster-Carr. “Triangle Power Bits” Confirms the three-point tip design, 1/4-inch hex shank, 2-inch length, and steel construction.
- McMaster-Carr. “TA20 Screwdrivers” Supports TA size-to-triangle-length figures and part number 5941A12.
- Lowe’s. “TEKTON Tamper Star/Triangle Security Torx Screwdriver Bit Set, Model DZZ92002” Source for the five-bit TA range, 8660 steel, HRC 55–58 rating, price, and lifetime warranty.