What Is a Pull Out Microwave? Drawer vs Built-in Explained

A pull out microwave, or microwave drawer, is a built-in unit whose cooking cavity slides out horizontally from the cabinetry instead of swinging open on a hinged front door.

Reaching over a hot door to lift a heavy casserole out of a wall-mounted microwave is the exact moment most people start shopping for something else. A pull out microwave removes that reach: the drawer glides toward you at counter level, the dish sits in a tray you can see into from above, and nothing swings out into a walkway. The catch is that a drawer and a conventional built-in are not interchangeable, and the cabinet opening decides which one you can actually install.

How Does a Microwave Drawer Actually Work?

The drawer mounts below a countertop, inside an island, or under another built-in appliance, and its cavity travels out on a track rather than pivoting on a hinge.

Sharp’s current 24-inch SMD2420MS shows the class standard: 1.2 cubic feet of capacity and 950 watts of cooking power, with automatic drawer opening and closing. Installation options listed by Sharp include islands, peninsulas, standard cabinetry, and mounting beneath another 24-inch built-in appliance. The 950 watts matter more than they sound — that’s a real cooking power figure, not a “warming only” rating, so the drawer behaves like a full microwave rather than a reheating drawer.

Sharp’s spec sheet for the SMD2420MS lays out the numbers a cabinet maker needs:

  • Product size: 23-5/8 in wide × 15-1/16 in high × 23-7/16 in deep
  • Standard cutout: 22-1/8 × 14-13/16 × 23-1/2 in
  • Flush-mount cutout: 23-7/8 × 15-5/16 × 23-1/2 in
  • Electrical supply: 120 V, 60 Hz, 15 A, 1.67 kW
  • Product weight: 72.0 pounds

Notice the product width is 23-5/8 inches while the standard cutout is 22-1/8 inches. That gap is the single most misunderstood part of buying one, and it’s covered below.

A Pull Out Microwave vs a Built-In Microwave: What’s the Difference?

A conventional built-in microwave opens toward you on a hinged front door and drops into a cabinet or wall opening, while a drawer unit opens from the top and slides out horizontally. Those are different physical mechanisms, not just different styling.

Because of that, the two formats are not interchangeable. Cabinet cutouts, door clearance, ventilation, electrical requirements, and mounting hardware are all model-specific. A trim kit made for a front-opening built-in will not adapt a drawer unit into the same opening, and a drawer drop-in won’t rescue a cabinet box cut for a hinged oven. The drawer format earns its price in kitchens where lifting a dish to chest height is genuinely difficult — under-counter runs, accessible layouts, and island setups where a swinging door would block a walkway.

If you’re weighing specific models side by side, our tested pull out microwave roundup breaks down the current options by price and capacity.

What Does Installation Require?

Installation is cabinet work with a hard electrical requirement, and Sharp’s microwave drawer installation manual specifies a 120 V, 60 Hz AC-only supply rated at 15 A or more.

The sequence, per Sharp’s documented steps, runs like this:

  1. Read the full installation manual before anything gets cut.
  2. Set the drawer beside the prepared cabinet opening.
  3. Plug the power cord into the required outlet.
  4. Slide the unit in without pinching the cord.
  5. Keep sliding until the mounting flange sits flush with the cabinet face.
  6. Open the drawer, pre-drill the four mounting holes with a 1/16-inch drill bit, and drive the four supplied screws.

The drawer pulls out and the flange sits tight against the cabinet front. One safety item is easy to skip: the same manual family requires an anti-tip block positioned 14-3/4 inches above the floor the drawer sits on. That’s a requirement, not an optional cabinet feature — a drawer that slides out with weight in it shifts the load forward.

What Do Drawer Microwaves Cost?

Two things to flag before you buy. First, those prices are what Sharp’s US pages display and can change. Second, smart and Wi-Fi features are model-specific — the SMD2479MW sheet lists them while the SMD2420MS and SMD2430MS sheets do not, so don’t assume connected features carry across the line. The SMD2430MS matches the SMD2420MS on capacity, wattage, dimensions, and cutout, which makes it a finish-and-feature decision rather than a performance one. The Deco Series also accepts an optional SKMD24U0ES pedestal accessory.

Which Mistakes Sink a Drawer Install?

Most failures trace back to the cabinet opening, not the appliance.

Reusing an opening sized for another 24-inch appliance without checking the exact model’s cutout is the big one. Confusing product width with required opening width causes the same problem from the other direction. Installing a standard-mount unit into a flush-mount opening — or the reverse — won’t work, and the cutouts differ by nearly two inches in width. Omitting the anti-tip block, routing the cord where it gets pinched, and assuming a conventional built-in trim kit fits a drawer all recur often enough that Sharp’s own documentation addresses each one. Confirm the circuit is a code-compliant 120-volt, 15-amp supply before the cabinet goes in, because rewiring after the fact means pulling the unit back out.

Common Questions

Can a microwave drawer go under a standard countertop?

Yes, provided the cabinet opening matches the model’s cutout. Sharp lists island, peninsula, standard cabinetry, and under-appliance mounting as supported options. The cutout — 22-1/8 × 14-13/16 × 23-1/2 inches on the SMD2420MS — is smaller than the unit’s 23-5/8-inch width, so the cabinet must be built to the cutout spec, not the product spec.

Do drawer microwaves need a dedicated circuit?

Sharp’s installation manual calls for a 120 V, 60 Hz AC-only supply rated at 15 A or more. Whether that circuit must be dedicated depends on local electrical code, so confirm with your electrician or building inspector before the cabinet is closed up. The unit draws 1.67 kW, which is substantial for a shared kitchen circuit.

Is a drawer microwave harder to clean than a built-in?

The cavity is shallower and wider than a typical front-loader — 17-5/16 × 7-1/8 × 16-9/16 inches on the SMD2420MS — so reaching the back corners takes a different motion. The trade is that you look straight down into the cavity with the drawer open, which makes spills easier to spot than in a door-front unit mounted at eye level.

Sources

Scroll to Top