Wear the sensor on top of the wrist, a finger’s width above the wrist bone, snug enough that it cannot slide but not tight enough to pinch.
An optical heart rate sensor reads blood flow through your skin, so anything between the sensor and your capillaries — a loose band, a smudge of sunscreen, a cold wrist — shows up as a wrong number. The fix is placement and fit, not a new device. Apple, Garmin, and Polar publish nearly identical guidance, and the rules below pull from all three.
Where Should the Sensor Sit on Your Wrist?
Position the device at least one finger’s width above the wrist bone, on the top or outer side of the wrist, so the sensor stays in constant contact with skin. Polar’s guidance is the most specific: tighten the band firmly enough that the sensor cannot move off the skin, then move it slightly farther up the arm during training.
Fit matters as much as location. Polar suggests pushing the band upward from both sides of the watch — the sensor should not lift away, and you should not see the green LEDs peeking out from under the case. If either happens, the fit is too loose.
For workouts, Apple recommends tightening the band and loosening it afterward; Garmin wants a snug, comfortable fit that does not shift while you run. Overtightening is its own problem: Garmin warns it can irritate skin without improving readings.
| Fit Problem | What It Does to Readings | The Fix |
|---|---|---|
| Band worn on or below the wrist bone | Sensor loses steady skin contact and drops out | Move it one finger’s width above the wrist bone |
| Band loose enough to slide or bounce | Motion creates erratic or missing readings | Tighten until the LED test passes |
| Band cranked painfully tight | Skin irritation with little accuracy gain | Loosen one notch after training |
| Sensor sitting over a tattoo | Light absorption shifts and readings fail | Shift position or switch wrists |
| Lotion or sunscreen under the sensor | Blocks the optical window | Wear the device on clean, dry skin |
| Starting hard exercise with cold hands | Low blood flow delays a stable signal | Warm up 10–15 minutes first |
| Sweat, dirt, or scratches on the lens | Weak or noisy signal | Rinse with fresh water after workouts |
What Prep and Warm-Up Steps Improve Accuracy?
Start with a clean, dry wrist and a clean sensor so the optical window sees skin clearly. Garmin advises cleaning and drying your arm before putting the watch on and keeping sunscreen, lotion, and insect repellent away from the area underneath the device. After workouts, Garmin recommends a fresh-water rinse; Polar advises mild soap and water with a full dry before charging.
Warmth is the step most people skip. In cold conditions, Polar notes that reliability depends on blood flow to the wrist and recommends keeping hands warm and the wrist covered.
Skin needs a few minutes to adapt as well. If readings stay stubbornly wrong, wear the device on the other wrist. Tattoos are a known complication: both Polar and Garmin flag them as a cause of inaccurate or unavailable readings.
Sensor hardware and band design vary a lot; our roundup of the best wrist heart rate sensors for training covers the models that hold contact best.
What Does a Wrist Sensor Measure — and Where Does It Fall Short?
Optical wrist sensors use photoplethysmography: green LEDs shine into the skin and photodiodes detect changes in blood flow, which the watch converts into a heart rate.
Apple says plainly that even under ideal conditions readings may occasionally be unreliable or unavailable, and substantial arm movement — especially with a loose band — degrades the data. Garmin advises a compatible chest strap when accuracy is critical or wrist measurement is problematic; wrist sensors and chest straps are not interchangeable.
A displayed heart rate is not a medical diagnosis; for chest pain, fainting, severe shortness of breath, or an unexpectedly extreme reading, seek medical care rather than trusting the watch. Keep the device clean and dry with a reasonable fit to prevent skin irritation.
The full routine, in order: clean wrist, correct position above the wrist bone, a firm band you can tighten for training, a warm-up before you start the timer, and a loose band afterward.
Common Questions
Should I tighten the band during exercise?
Yes. Apple and Polar both recommend a tighter fit for workouts, because motion is the biggest cause of dropped readings. Tighten until the sensor cannot shift, then loosen the band afterward so your skin can breathe. Avoid going so tight that it pinches.
Can a wrist sensor read through a tattoo?
Often it cannot. Both Polar and Garmin identify tattoos as a possible source of inaccurate or missing readings, since ink changes how light passes through the skin. If your sensor sits directly over a tattoo, shift it slightly or wear the device on the other wrist.
Why is my heart rate wrong at the start of a run?
Cold skin and sudden motion both disrupt the optical signal. Warm up for 10–15 minutes before starting the workout timer, keep your hands and wrist warm in cold weather, and give the sensor a few minutes to lock on before you judge the number.
Sources
- Polar. “Troubleshooting optical heart rate measurement” Source for wrist-bone placement, the band-tightness test, warmth, and tattoo guidance.
- Apple. “Heart rate monitoring on Apple Watch” Source for photoplethysmography, the 30–210 bpm range, and fit guidance.
- Garmin. “Wearing the Device and Heart Rate” Source for placement, warm-up timing, cleaning, and chest-strap advice.