A VESA 400×300 mount accepts TVs whose rear mounting holes sit 400 mm apart horizontally and 300 mm apart vertically; brackets that cover a VESA range including 400×300 also fit.
A VESA 400×300 wall mount fits a rectangular hole pattern: 400 millimeters across and 300 millimeters down, measured center to center between the threaded holes on the TV’s back. Any other pattern—400×400, 400×200, 300×300—won’t line up without an adapter, regardless of screen size.
“VESA compatible” on a product page tells you almost nothing. Confirm the exact pattern, the weight rating, and your wall before buying. One table below shows real Sony models whose patterns differ sharply despite similar screen sizes.
What Does VESA 400×300 Actually Mean?
VESA 400×300 describes a physical mounting interface—two horizontal holes 400 mm apart and two vertical holes 300 mm apart, on centers—and says nothing about screen technology, resolution, or brand.
Measure center-to-center, not from the outer edges of the screw recesses; those are wider, and edge-to-edge readings can run 10–20 mm off—enough to make a correct mount look wrong.
Two conventions cause problems. Some manuals label the same interface “VESA hole pitch,” “VESA mounting pattern,” or “screw-hole pattern”—same thing. And a bracket listing a range such as 200×200 to 600×400 can still support 400×300, but the manufacturer’s compatibility chart settles it—not the maximum number on the box.
How Do You Check Whether Your TV Fits?
Confirming fit takes about five minutes with a tape measure and your TV’s manual. Measure first, then verify against the manufacturer’s specs.
- Lay the TV face down on a padded surface with the stand removed.
- Find the four threaded holes in the rear panel, usually in a rectangle.
- Measure horizontally between hole centers—you want roughly 400 mm (about 15.75 inches).
- Measure vertically between hole centers—target roughly 300 mm (about 11.81 inches).
- Look up your exact model number in the manufacturer’s spec page or manual; a suffix difference can change the chassis.
- Check the TV’s weight without its stand against the bracket’s rated capacity.
- Confirm the bracket’s supported VESA list explicitly includes 400×300.
Screen size tells you nothing reliable. Four sizes, four patterns, one product family.
Which TVs Use a 400×300 Pattern?
Large-screen models are the common case, but the only reliable answer comes from the model number. Sony’s documentation confirms several examples.
| Sony Model | Screen Size | VESA Pattern & Weight |
|---|---|---|
| BRAVIA 6 K-77A60 (2026) | 77 in | 400×300 mm; ~55.3 lb without stand |
| BRAVIA 6 K-77A60C (2026) | 77 in | 400×300 mm; ~55.3 lb without stand |
| XH9505 KD-75XH9505 (2020) | 75 in | 400×300 mm; 33.1 kg without stand |
| BRAVIA 6 K-83A60 (2026) | 83 in | 400×400 mm—does not fit |
| BRAVIA 6 K-65A60 (2026) | 65 in | 400×200 mm—does not fit |
| BRAVIA 6 K-55A60 (2026) | 55 in | 300×200 mm—does not fit |
Notice the 83-inch model: bigger screen, wrong pattern. Check your panel’s stand-free figure rather than assuming similar-size TVs weigh the same.
If you’ve confirmed your pattern and want mounts with real weight ratings and hardware kits, this roundup of tested VESA 400×300 wall mounts compares the options side by side.
What Else Must Match Beyond the Hole Pattern?
Screw size, weight capacity, and wall structure each disqualify mounts that look compatible on paper.
Screws. VESA dimensions say nothing about thread diameter or screw length; those come from your TV’s manual and the bracket’s hardware list. Sony warns that on some BRAVIA models the hole spacing matches VESA standards while the number and depth of threaded holes do not—never force a longer screw or skip a supplied spacer.
Weight. Use the stand-free weight, not shipping weight or weight with the stand. A bracket rated below your TV’s actual figure is a hazard, not a near miss.
Wall and anchors. Drywall alone will not hold a 55-pound television. Mount into studs or use masonry anchors rated for the combined load, and follow the bracket maker’s fastener and torque instructions. Sony directs users to a qualified installer when wall construction is uncertain.
Clearance. Tilt and swivel brackets need room behind the panel for cable bend radius, ventilation, and power access. Check the movement range before tightening anything.
Common errors: confusing 400×300 with 400×400 or 400×200, picking a mount by screen size, and trusting a bracket’s maximum VESA figure without seeing 400×300 in its supported range.
Common Questions
Can I use a 400×400 mount on a 400×300 television?
Not directly. A 400×400 bracket’s vertical holes sit 400 mm apart, while your TV’s are 300 mm apart, so the arms won’t reach. Some multi-pattern brackets include slotted arms that bridge the gap, but only if the manufacturer’s compatibility chart explicitly lists 400×300. Verify before buying.
Where do I find the VESA size for my TV?
Check the printed manual, the manufacturer’s online spec page for your exact model number, or a label on the rear panel. Measure hole spacing center-to-center as a cross-check. Regional model suffixes can carry different chassis specs, so match the full US model number rather than the series name.
Does a bigger screen always mean a bigger VESA pattern?
No. Sony’s 2026 BRAVIA 6 range shows the 83-inch at 400×400 and the 77-inch at 400×300, but patterns jump around across the lineup rather than scaling predictably. Screen size and brand never establish compatibility—only the specific model’s documented pattern does.
Sources
- Sony. “Compatible wall-mount brackets and screw hole distance measurements for BRAVIA TVs (2026 models)” Supplies the 2026 BRAVIA model-by-model VESA patterns and weights.
- Sony. “Compatible wall-mount brackets and screw hole distance measurements” Documents VESA measurement conventions and bracket compatibility guidance.
- Sony. “Wall mounting—compatible Wall-Mount Brackets and screw hole distance measurements” Explains screw-hole depth variation and installation cautions.