Stackable Washer and Dryer Dimensions and Clearances Explained | Real Numbers First

A full-size stacked washer and dryer typically measures about 27 inches wide, 30 to 33 inches deep, and 77 to 81 inches tall — before you add rear plumbing space, venting, and an open dryer door.

The number that sinks most installations isn’t the one printed on the box. It’s the depth with the dryer door swung open, which reaches 51⅜ inches on LG’s DLE3400W and 59 inches on the DLEX8900B. Cabinet width gets measured; door swing and hose clearance get forgotten. Below are the real figures pulled from LG’s current spec sheets, the clearance rules that actually govern an alcove or closet, and the measurements to take before you buy.

Stackable Washer and Dryer Dimensions: The Numbers That Matter

Full-size stacked pairs cluster around 27 inches wide, and height depends almost entirely on whether the base is a compact heat-pump dryer or a full-size drum. Width is the number buyers fixate on, but depth and door swing decide whether a unit fits a hallway or a closet.

Model / Pairing Key Dimensions Clearances Specified
LG WM4000H washer (stacked) 27 in. wide × 30¼ in. deep; 77½ in. stacked height 1 in. per side, 4 in. behind
LG WM6500H washer (stacked) 27 in. wide × 33⅛ in. deep; 77½ in. stacked height 1 in. per side, 4 in. behind
LG WM5800H washer 27 in. wide × 39 in. high × 33⅛ in. deep; 57¾ in. deep with door open 1 in. per side, 4 in. behind
LG WM8900HBA washer (stacked) 29 in. wide × 32⅞ in. deep; 81⅝ in. stacked height 1 in. per side, 4 in. behind
LG DLE3400W / DLG3401W dryer 27 in. wide × 38 11/16 in. high × 30⅛ in. deep; 51⅜ in. deep with door open Tested with 1 in. side and rear
LG DLEX8900B / DLGX8901B dryer 29 in. wide × 40¾ in. high × 32⅛ in. deep; 59 in. deep with door open Match the paired washer’s spec sheet
LG DLHC1455W compact heat-pump dryer 24 in. wide; 6 in. overhead clearance listed 1 in. side, 5½ in. rear

A compact stack is the real narrow-space option, and our tested roundup of thin stackable washer and dryer picks covers the models that squeeze into 24-inch openings.

How Much Clearance Does A Stacked Unit Really Need?

LG’s stacking guidance calls for 2 inches on each side, 4 inches between the stacked unit and the wall, and 2 inches above the top of the unit to the ceiling.

That 4-inch rear gap is not cosmetic. Hoses, the drain, and the dryer vent all live back there, and pinching them causes vibration, kinks, and airflow problems. Minimum opening sizes scale with machine width: about 27.6 × 70.5 inches for 24-inch machines, 29.5 × 73.6 inches for 25-inch machines, and 31.5 × 75.6 inches for 27-inch machines.

Closets add a second layer of rules. Installations specify ventilation openings of at least 48 square inches up top and 24 square inches low, with the upper opening no lower than 6 feet above the floor and the lower one no more than 1 foot above it. Cover those openings with a shelf or a stack of towels and the dryer runs hot.

Can You Stack Any Washer And Dryer?

No — a washer and dryer can only be stacked when the manufacturer approves those exact models as a pair and specifies a stacking kit or bracket. Matching brand logos on the front is not approval.

The practical sequence the manufacturer’s installation guide lays out:

  1. Confirm the two model numbers are approved for stacking together.
  2. Verify alcove width, ceiling height, depth, door-opening room, and hose or vent clearance.
  3. Use the specified stacking kit — never set a dryer directly on a washer.
  4. Install the brackets or drawer-type stacking frame per the kit instructions.
  5. Secure the assembly as directed; guidance requires the bracket to be attached to a wall.
  6. Level the washer before stacking, then check the finished assembly for wobble.
  7. Hook up water, drain, electrical, gas, and exhaust per each appliance’s documentation.
  8. Run both machines and check for vibration, drainage, airflow, leaks, and door swing.

You’ll know it went right when the stack sits steady during a high-speed spin cycle and the dryer door opens with room to load. If the unit walks across the floor, the washer isn’t level or the bracket isn’t anchored.

The most common measuring mistakes: using nominal width as the cutout width, ignoring baseboards, door trim, and vent elbows, assuming any front-load pair stacks, and mixing brands without explicit compatibility approval.

Which Measurements Should You Take Before Buying?

Measure the opening at its tightest point — baseboard to baseboard, floor to ceiling, wall to front trim — then subtract the door-open depth and the 4-inch rear gap. Write down five numbers: opening width, opening height, opening depth, distance to the nearest doorway or wall, and ceiling height above the floor.

Compare those five numbers against the spec sheet for your exact models, not against a generic 27-inch figure. If your opening is under about 28 inches wide, a compact 24-inch pair is the honest answer, and the dryer typically needs 5½ inches of rear room and a listed 6 inches overhead. When the numbers fit, stacking frees floor space and puts the dryer at chest height — when they don’t, forcing it means pinched hoses, a rattling cabinet, and a warranty conversation nobody enjoys.

Common Questions

How tall is a stacked washer and dryer in feet?

Most full-size stacked pairs land between 77½ and 81⅝ inches, which is about 6 feet 5½ inches to 6 feet 9⅝ inches. Add the ceiling clearance of at least 2 inches on top of that. Compact heat-pump stacks run shorter, so check the specific model’s spec sheet rather than assuming a standard height.

Do stacked units need space behind them?

Yes. The manufacturer specifies 4 inches between the stacked unit and the wall. That gap protects the water hoses, the drain hose, and the dryer vent from kinking or crushing. It also feeds airflow, which a heat-pump or vented dryer needs.

Can I stack a dryer on top of any front-load washer?

No. Stacking requires the manufacturer to approve those two exact model numbers as a pair and to specify a stacking kit or bracket. Front-load designs from different brands or even different model families may not align or bear load the same way. Using unapproved hardware voids coverage and creates a tipping risk, especially since the bracket must be secured to a wall.

Sources

Scroll to Top