How to Size a Tankless Hot Water Heater for a Mobile Home? | GPM Math

Sizing a tankless unit for a mobile home takes two numbers: peak hot-water flow in gallons per minute and the rise from your coldest inlet water.

Square footage and bathroom counts tell you nothing. A 900-square-foot mobile home with two showers running can out-demand a 2,500-square-foot house with one tap open.

Get the flow wrong and the heater cycles cold every time a second fixture opens. Get the rise wrong and it never reaches the setpoint. Sizing starts with two measurements and ends at a manufacturer’s performance chart.

Sizing A Mobile Home Tankless Heater: The Numbers That Decide It

Peak simultaneous flow and temperature rise decide whether a unit keeps up. A headline gpm rating means nothing until you know what rise it was measured at.

  1. Pick the outlet temperature. The Department of Energy’s tankless measure guideline treats 120°F as the typical household target. Every degree above adds rise and scald risk.
  2. Find the coldest inlet water. Ask the local water utility for its winter minimum. The annual average undersizes the heater in the month you notice most.
  3. Add the fixtures that genuinely run together — the realistic overlap, not every tap. DOE’s typical ranges are in the table below.
  4. Read a performance chart. Manufacturers publish capacity at specific flow rates and temperature rises. That chart sizes the heater, not the box.
  5. Check activation flow. Most tankless heaters need about 0.5 gpm of draw to fire. A low-flow showerhead or weeping valve can sit under that and hand you cold bursts.

The Department of Energy’s measure guideline for tankless water heaters runs the same sequence and explains why a maximum-flow figure alone misleads.

Fixture Typical Hot-Water Flow
Bathroom sink 0.5–1.5 gpm
Showerhead 1.5–2.5 gpm
Bathtub 2.0–4.0 gpm
Kitchen sink 1.0–2.5 gpm
Dishwasher 1.0–3.0 gpm
One shower plus one sink (common one-bath example) About 2–3 gpm

What Temperature Rise Do You Actually Need?

Temperature rise is the target outlet temperature minus the coldest incoming water, and it shrinks usable capacity.

Drawing 40°F groundwater and aiming for 120°F at the tap means an 80°F rise. A unit rated 6 gpm at a shallow rise might deliver well under that at 80°F.

DOE’s Building Science Education material on gas-fired tankless units reports that residential gas models generally heat more than 5 gpm at a 60°F rise — often enough for two showers — and puts gas near 5 gpm and electric near 2 gpm at a 70°F rise. Cold regions land lower because inlet water runs colder.

A second shower, dishwasher, and washing machine at once usually means a larger gas unit or staggered loads. Some heaters also throttle output when the requested temperature can’t be held at the flow you opened; DOE documentation describes that behavior. You get warm water at the tap, not a fault light.

Mobile Home Installation Checks That Decide The Model

A correctly sized heater still fails if the home cannot feed it, vent it, or house it legally.

  • Listing and code. The unit must be listed for the location and fuel type and installed per its manual, local building code, and mobile-home requirements.
  • Gas capacity. Traditional tankless burners commonly run 150,000 Btu/h or more. Verify line size, regulator capacity, combustion air, and control power.
  • Electrical service. Electric models can demand high voltage and amperage. Confirm breaker, conductor, and panel capacity first — many mobile-home services can’t carry the load.
  • Venting. Cold climates call for sealed-combustion direct-vent or power-vented equipment, terminating above expected snow level and separated enough that exhaust frost cannot block the intake.
  • Freeze and service access. Insulate piping, fit isolation valves, respect manual clearances, and plan for scale control.
  • Scald protection. A thermostatic mixing valve belongs on any system above 120°F, and code may require one.

Replacing an existing gas tank heater is the moment to measure the gas line, since a tankless burner pulls far more Btu/h than the tank it replaces. Run the checks in order: winter inlet temperature, realistic simultaneous gpm, performance at that rise, activation flow, then gas or electrical capacity. A unit that clears all five fits; one that misses any is the wrong heater, whatever the box claims. Our tested tankless picks for mobile homes starts from models that clear them.

Common Questions

Can A Tankless Heater Handle Two Showers In A Mobile Home?

Usually yes with gas, rarely with electric. DOE reports gas tankless models generally heat more than 5 gpm at a 60°F rise, covering two standard showerheads, while electric units land near 2 gpm at a 70°F rise. Check your winter inlet temperature first, because colder groundwater cuts delivered flow.

Does A Mobile Home Need A Different Tankless Unit?

Sometimes. The heater must be listed for the installation and approved under its manual, local code, and mobile-home rules, and the home’s gas supply, venting, and electrical service have to support it. Electric models are the usual sticking point, since a mobile-home service often lacks the amperage a large electric tankless unit draws.

Why Does Tankless Water Go Cold Then Hot Again?

The usual cause is draw below the activation threshold. Most tankless heaters need about 0.5 gpm to fire, so a low-flow showerhead or partly closed valve can shut the burner down mid-shower. Some units also reduce flow when they can’t hold the set temperature at the volume you opened.

Sources

Scroll to Top